I keep putting the pressure on the rep for hard switches or wireless stomp buttons. There is a hard switch on the control box I'm sure it would not be hard to tap. Holding force solid. 👍
Love them just installed them. Issue it is impossible to snake them through my motor engine tube. The connects are way too big. Can you cut the lines drill holes in the boat an pull them through an install them like most people do standard power poles. An splice the lines back together. Looks like to me there’s several wires in the line but looks like only two wires that are ran to the connector the ground and positive. Can this be done?
@@johnburris5927 To me wires are wires, good splice and waterproof connection would work. However reaching out to support first is never a bad move just to play it safe.
Had a thought while driving to work. Here is a better option. Disconnect the wires from inside the box. Then run the wire from the poles to the box and all you would need to do is crimp on new ends and they would be in the waterproof box. Saves you a point of failure. Instead of cutting "mid-wire"
@@Mitz-RI heading to headwaters fla looking for installing bobs 6 inch jack plate and poles glad I seen these This is what I’ve been looking for no hyd 10 foot are they ready
I have had mine on the boat for the entire season and they work well. Very easy to setup and use. I've also been in contact with my rep and they are dedicating a lot of time into these units Including adding new features and accessories. Should see a lot more from them over the next few months. I'll also be posting a end of the year video summary in a week or 2.
@@davidstottlemyer try this link www.lippert.com/lewmar-quick-release-mounting-bracket-2023043513?srsltid=AfmBOorpQovj1J4kY_6CKfr3-XeoZjPTv20MJHiC8kmGHWllHUGNN3g5BuE
Side note on this. I'm wrapping up the install and I have them both wired with the inline fuse and tied to individual fuses on a dedicated accessories panel. Each were tied to a 10amp and if the SWA was up and you hit up again it would pop both 10s. Jump to 20 and no issues while testing. PS inline never tripped. Definitely more testing to do!
I can't see why not, it would come down to the bolt pattern of your jack plate. The left to right on center are 3 11/16" top to bottom on center are 4 11/16". I can reach out to my contact and see if they have any official stance.
@chrism8013 @marvinmckemy7213 I just heard back from my contact. I asked him two questions. Is there a Jack Plate option, and is there a wireless "Stomp" Button option? He replied "Yes and Yes. Also said most common mounts have the same bolt patterns."I'm now working on getting images and pricing!
I just bought two of these and had my boat service guys install them for me. For some reason they couldn't synchronize the two SWAs with one key fob for latching operations. Is there a trick to this step?
Hi! There was a bit of playing around to make it work. This weekend, I started the video on mounting them to the boat. I'm also going to create a short video on how to sync the remote. Are you in a rush? Hopefully, I should have the video up this week.
@bmiller1672 The new video is done just going to take some time to edit before posting. SO here is what you need to do. 1. CLEAR All Settings (Press and hold mode for 3 sec. Light will go solid then flash then turn off). 2. Next on both at the same time Press and hold program button for 3 seconds while both lights are solid 3. Press the UP arrow. Then wait don't touch anything until the light flashes quickly and turns off. It should then work for both Anchors. Video should be up sometime this week.
A bit but the echo in the garage doesn't help. I had one set up in the basement, and it wasn't that bad. Next video, they will be installed on the boat, and I'll get a true outside test. Will keep you posted!
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Thanks for the video. Is a hard Mount switch available for a dash panel? And hows the continues pressure or down force on the floor bed?
Thanks again
I keep putting the pressure on the rep for hard switches or wireless stomp buttons. There is a hard switch on the control box I'm sure it would not be hard to tap. Holding force solid. 👍
Love them just installed them. Issue it is impossible to snake them through my motor engine tube. The connects are way too big. Can you cut the lines drill holes in the boat an pull them through an install them like most people do standard power poles. An splice the lines back together. Looks like to me there’s several wires in the line but looks like only two wires that are ran to the connector the ground and positive. Can this be done?
@@johnburris5927 To me wires are wires, good splice and waterproof connection would work. However reaching out to support first is never a bad move just to play it safe.
Had a thought while driving to work. Here is a better option. Disconnect the wires from inside the box. Then run the wire from the poles to the box and all you would need to do is crimp on new ends and they would be in the waterproof box. Saves you a point of failure. Instead of cutting "mid-wire"
Can you sync 2 to one remote and control them individually?
The manual switch on the box will override remote. The remote either one or both.
What’s the warranty
I have an old 2000. 520 and no room this just might make me change my mind very soon
Is there a jack plate brackets?
@@jchensley1 jack plate is a standard bolt pattern. Anything from those "poles" should work. Warranty I would say to jump on the site just to confirm.
Did I hear you say 8 foot ?
@@jchensley1 8ft unit secures in up to 7ft, pretty sure there is a 10ft ready to go this season.
@@Mitz-RI heading to headwaters fla looking for installing bobs 6 inch jack plate and poles glad I seen these
This is what I’ve been looking for no hyd
10 foot are they ready
@jchensley1 saw it online at one of the boat shows. I can reach out to my rep Monday to check and see if it's on the market. 👍
I would love some reviews from actual people that have these installed. I cant find any. Im ready to buy these but would like actual feedback.
I have had mine on the boat for the entire season and they work well. Very easy to setup and use. I've also been in contact with my rep and they are dedicating a lot of time into these units Including adding new features and accessories. Should see a lot more from them over the next few months. I'll also be posting a end of the year video summary in a week or 2.
any 10 foot models in the future
Not that I have heard in 2023-24 but they do have a bunch happening in the background. I'll poke my contact and see if I can get any insight!
@davidstottlemyer , I did hear back and was told "yes"; it is currently in development! So, I guess they are further along than I thought!
where did you get the quick disconnect mount at ?
@@davidstottlemyer try this link www.lippert.com/lewmar-quick-release-mounting-bracket-2023043513?srsltid=AfmBOorpQovj1J4kY_6CKfr3-XeoZjPTv20MJHiC8kmGHWllHUGNN3g5BuE
What's the amperage of the inline fuse? Also, if you know by any chance, what's the amperage draw?
Inline Fuse is a E37 K 05A Ignition Protection Fuse. Actual draw I can test when I do the boat install this coming week.
Appreciate the info, i'll looking forward to the install!
I also would like to add that even the 5A fuse is a really impressive number to get down to, where as competition uses a 40A fuse with 33A-36A draw
@@traceroberts3455 gear driven vs hydraulic pump al lot less work on the motor. Let me reach out to my contact and see what they say. 👍
Side note on this. I'm wrapping up the install and I have them both wired with the inline fuse and tied to individual fuses on a dedicated accessories panel. Each were tied to a 10amp and if the SWA was up and you hit up again it would pop both 10s. Jump to 20 and no issues while testing. PS inline never tripped. Definitely more testing to do!
Is it jack plate mountable, or just transom mount?
I can't see why not, it would come down to the bolt pattern of your jack plate. The left to right on center are 3 11/16" top to bottom on center are 4 11/16". I can reach out to my contact and see if they have any official stance.
@@Mitz-RI Thanks!! A word from an official rep would be great. Bob's & Atlas adapters would be really nice.
Any answer on this yet? I sure would like to see a Jack plate mount or adapter that could be used with existing Jack plate mounts.
@@Pimpdaddy4791 I will reach out to the rep I dealt with today and see what I can find. 👍 I know there is a lot in development.
@chrism8013 @marvinmckemy7213 I just heard back from my contact. I asked him two questions. Is there a Jack Plate option, and is there a wireless "Stomp" Button option? He replied "Yes and Yes. Also said most common mounts have the same bolt patterns."I'm now working on getting images and pricing!
I just bought two of these and had my boat service guys install them for me. For some reason they couldn't synchronize the two SWAs with one key fob for latching operations. Is there a trick to this step?
Hi! There was a bit of playing around to make it work. This weekend, I started the video on mounting them to the boat. I'm also going to create a short video on how to sync the remote. Are you in a rush? Hopefully, I should have the video up this week.
@@Mitz-RI just got back from Spring Break. Look forward to seeing your video on how to sync two rf modules to one remote.
@bmiller1672 The new video is done just going to take some time to edit before posting. SO here is what you need to do. 1. CLEAR All Settings (Press and hold mode for 3 sec. Light will go solid then flash then turn off). 2. Next on both at the same time Press and hold program button for 3 seconds while both lights are solid 3. Press the UP arrow. Then wait don't touch anything until the light flashes quickly and turns off. It should then work for both Anchors. Video should be up sometime this week.
@@Mitz-RI appreciate the follow-up and will try this out and let you know the outcome. Thanks.
@@BluntTruth7we connect two of them regularly. If you still have trouble ask to speak to your local rep. Where are you located?
Really loud isn't it????
A bit but the echo in the garage doesn't help. I had one set up in the basement, and it wasn't that bad. Next video, they will be installed on the boat, and I'll get a true outside test. Will keep you posted!