I know you don't want to redrill 6 holes that hold the front or rear frame down, but the side bars are important for bracing your rack - fore and aft. Alternatively you could put some spacers in the gaps on the side bars and then bolt through, so that you can do up the two flanges on each end of the side bars. I'd hate to see the roof top tent on the ground on a gnarly steep track or serious congregations.
Hello, after some advice. RE the mounting bars on the roof top tent - we are struggling to align the base of the roof top tent with the tub rack because the mounting bars are not wide enough. When we tried to adjust them to fit the width of the tent's bars on it's base, there wasn't a way to secure the cross bars back onto thee rack. Does that make sense? Help! (basically, keen to know if you had to drill new holes to the base of the tent)
Hey, I didn’t need to drill new holes in my tent but I did drill new holes into tub rack as I saw it didn’t align. Drilling holes into rooftop tent will cause water and condensation leakage!
We bought one a d have it installed. My question is with the ladder. Instructions say it should be at a specific angle. Tho the kings store say it doesn't as its not a support for the tent. Do you know if it matters its at (I think) a 35degree angle? Only ask cuz we need to fit 2 self inflating mattresses in our 4 person Annex
Hi mate - I’m the middle of building my own and also find gaps between the brackets for the ones on the side. What’s the correct way of building so you don’t have the gaps? Cheers 👍
Drivetech lift man, 2 inch front and rear but rear is 350kg constant. Will be dropping a new video on a rundown soon so make sure to stay tuned for it!
Ha! First thing I thought when I opened the instructions was these are fkn useless 😂. Thanks for the vid, very helpful
Hahah glad it wasn’t just me!
I know you don't want to redrill 6 holes that hold the front or rear frame down, but the side bars are important for bracing your rack - fore and aft. Alternatively you could put some spacers in the gaps on the side bars and then bolt through, so that you can do up the two flanges on each end of the side bars. I'd hate to see the roof top tent on the ground on a gnarly steep track or serious congregations.
I agree mate, spacers have been made. Appreciate the honesty!
You able to do a lil video or explanation on you’re tonneau cover on how you cut around the kings rack would love to know cos I’m in the predicament.
Hello, after some advice. RE the mounting bars on the roof top tent - we are struggling to align the base of the roof top tent with the tub rack because the mounting bars are not wide enough. When we tried to adjust them to fit the width of the tent's bars on it's base, there wasn't a way to secure the cross bars back onto thee rack. Does that make sense? Help! (basically, keen to know if you had to drill new holes to the base of the tent)
Hey, I didn’t need to drill new holes in my tent but I did drill new holes into tub rack as I saw it didn’t align. Drilling holes into rooftop tent will cause water and condensation leakage!
We bought one a d have it installed. My question is with the ladder. Instructions say it should be at a specific angle. Tho the kings store say it doesn't as its not a support for the tent. Do you know if it matters its at (I think) a 35degree angle? Only ask cuz we need to fit 2 self inflating mattresses in our 4 person Annex
No doesn’t matter what angle the ladder is at, as long as it touches the ground
Hey mate , do you know the height of the highest point from the ground with that setup . ?
Hi mate - I’m the middle of building my own and also find gaps between the brackets for the ones on the side. What’s the correct way of building so you don’t have the gaps? Cheers 👍
You need to assemble all the pieces before placing on car. So put everything on the rack that’s included and then place on car
Hey is was that the lowest setting in the tub rack how heigh was it compare to your roof height ?
Hey mate. Yes that was the lowest and was about 5cm off the roof height
Hi Mate, when ya cut around the tonneau cover, did it rip any more or did it stay after a bit of use?
Stayed like that man didn’t rip anymore
@@SammySharpp What Tonneau Cover do you have man? My EGR cover wont work with the tub rack so need a new one
How many bolts did you put in on the tub near the cab
Yeah figuring that out for myself right now. MQ Triton aswell.
Hey bud,
This is off track, bud whats the brand of suspension are you running front and rear.
Drivetech lift man, 2 inch front and rear but rear is 350kg constant. Will be dropping a new video on a rundown soon so make sure to stay tuned for it!
What did you cut around the cover with?
Just a Stanley knife and side cutters man
Did you used bolts in the tub where the chrome roll bars needer the cab
Cute haircut
Thanks mate
So useless video to see where and what part the rtt rails are mounted on 🤦♀️
Thanks mate appreciate the kind words!