I've wound a few of these for high power flyback converters, I recommend you sandwich the primary between the layers of the secondary, it decreases leakage inductance.
@@picanazo420 bread on the top and bottom and ingredients on the middle. here the bread is the primary coil and the ingredients is the secondary. half primary on bottom and other half on top.
sir do u know how to run an ignition coil with mosfet since it do not have the center tap wire for zero potential ground wire in the middle of primary :( plzzz tell me how to run ignition coil with the same mosfet ????????
Thank you for this video. Just a question. Will this detonator work if the last cycle was incomplete? I mean, I made 9 cycles of 100 and the wire ran out. The last cycle was not completed. Will the process succeed or not? Thank you.
I have made the transformer,but the plasma does not appear in the high voltage cable,but it appears between the wire windings that are in the transformer screw.How do i handle it?
Sugianur Sugi use insulated wire, unless you already did. Enabled copper wire. If you can’t figure that out I highly suggest you don’t do something as dangerous as this
aa... how to winding secondary coil? free winding or how to? i make it like that, i always fail. the noise very high but nothing plasma arc like that. please tell me how to make second coil
Not free winding. One side to other side. Example right to left or left to right. So different potential wires will not touch each other. If touch then can be short circuit.
@@apocaloptigon9988 here, the tape have many thickness to choose.. but i dont know about that in your place.. my sugestion for you.. try to use tafelone tape/piping thrade tape. Its better..
I tried this and using tv flyback transformers and different mosfets, bjts, opamp square wave, and square wave inverter I made and still nothing! so frustrating for some reason none of my circuits ever work uggh! thanks for the video though
The thing is you use 100 mega ohm resistor...not 1k..regarding to the transformer you better wound only ONE-TWO LAYERS of insulating tape..not selotape
I made it exactly like this but it is not working in power of 2 AA batteries(3 V) Do i need 3.7 V..... It is working slow in mobile 3.7 V battery........ Plzzz tell me the POWERSUPPLY
I've wound a few of these for high power flyback converters, I recommend you sandwich the primary between the layers of the secondary, it decreases leakage inductance.
What did You mean with sandwich?
@@picanazo420 bread on the top and bottom and ingredients on the middle. here the bread is the primary coil and the ingredients is the secondary. half primary on bottom and other half on top.
thank you. i have learned alot.
can I use D880 trans.. and 120 ohm resistence
Can I increase the spark gap using high voltage ceramic capacitor parallel to the secondary.
You are creative
whats the output voltage sir?
Could you can use 12v battery?
Hello. 1k resistor is too big if you use mosfet. 100ohm resistor is enough. Or 220ohm resistor for 1500 winding secondary.
uma dúvida, cada camada do fio mais fino deve ser enrolada na direção oposta a camada anterior??
Can we use normal transformer from CFR bulb
will wire from clock work also will d882 npn transistor work
Nicely crafted, nice video, I currently know almost zero about Electronics. There was a lot of information here for me. I'm a subscriber.
+Death Becomes
Thank you very much
Death Be6vof pm mmes You >00 kg; 6v
Which size core use
Hi
i have put 5 layers of transparent tape. but my plasma arc is generating inside the transformer. what can i do?
First winding ke ketne turns hai ye nhi bataya apne sir?????
Can I use IRF3205 ??????
sir do u know how to run an ignition coil with mosfet since it do not have the center tap wire for zero potential ground wire in the middle of primary :( plzzz tell me how to run ignition coil with the same mosfet ????????
Circuit diagram?
Thank you for this video. Just a question. Will this detonator work if the last cycle was incomplete? I mean, I made 9 cycles of 100 and the wire ran out. The last cycle was not completed. Will the process succeed or not? Thank you.
Sir hamein bhi shock lag sakta hai kya
Can we keep 700 turns sir plz replay me🙏
verey nice
Set mujhe 240 volts se cigrete push Batan se jalane ka circite Kaiser banta hai bats dijiye plz.
Very nice
I have made the transformer,but the plasma does not appear in the high voltage cable,but it appears between the wire windings that are in the transformer screw.How do i handle it?
Sugianur Sugi use insulated wire, unless you already did. Enabled copper wire. If you can’t figure that out I highly suggest you don’t do something as dangerous as this
aa... how to winding secondary coil? free winding or how to? i make it like that, i always fail. the noise very high but nothing plasma arc like that. please tell me how to make second coil
Not free winding. One side to other side. Example right to left or left to right. So different potential wires will not touch each other. If touch then can be short circuit.
Niece work
Hi, my FET burns up after just few moments, im not sourcing current continuously but rather switching it.
Sounds like you set your gate backwards
Niec pic video
+Dilip Rajbhar
Thank you
How to make the primary coil?
+Sugianur Pemanen Sawit
16 + 16 turns of 0.5 m.m enameled wire.
Thank you
I don't think that 50 layers of tape plus 10 layers winding will fit in such small ferrite core.
I made around 5 layers and it works
@@apocaloptigon9988 here, the tape have many thickness to choose.. but i dont know about that in your place.. my sugestion for you.. try to use tafelone tape/piping thrade tape. Its better..
If i have broken ferrite transformer. Can I duct tape it to work? Or once broken it will be uneffcient? Or not working at all?
It will work but not perfectly
@@TechIdeasAG Thanks. I'll order few. seems like they are exremelly cheap.
I tried this and using tv flyback transformers and different mosfets, bjts, opamp square wave, and square wave inverter I made and still nothing! so frustrating for some reason none of my circuits ever work uggh! thanks for the video though
if i had the compoments u're quoting i could make 50 million voltage out put sparks with a 9 volt bettery. i need stuff but its all quarantined
Please i want the équivalent of the MOSFET z44
Wich z44 transistor equivalent? Can i use 13007?
yes but use 100 ohm in the base :)
diagram please
Can i use a TK15H50C MOSFET ???
Hmm,
It's 250v 15A N - ch MOSFET. It will work fine. But don't let it run when it's too hot.
Thank you
Wow !!
Pls tell the correct diameter of wire used in primary I don't think it's 1mm
ABHILASHA MORE yes i also want to know
it
0.3- 0.1 has worked for me
0.5
Why didn't my detonator work?
Can I use 0.2mm wire for secondary windings?
Yes. But impossible to fit in core for more windings. 0.05mm -0.1 mm is better.
0:35 what is 707...? please Mr Tech Ideas explain , not clear enough :( how you get 4 wires on primary coil?
@@crescendo7357 THNX SO MUCH !
like 7 turns clockwise then 7 turns anticlockwise
Sir please tell 1mm = ?? gauge and no. Plzz sir reply
Google the math. Length and awg matter
What happened when I winding less then 100 ???
My boy XPLUS NOTHING BRO.. ITS MIGHT REDUCE OUTPUT VOLTAGE LEVEL... ANY WAY IT WIL SURE TO WORK
Thanks for reply
Are you sure this isn't alien technology 🤔
The thing is you use 100 mega ohm resistor...not 1k..regarding to the transformer you better wound only ONE-TWO LAYERS of insulating tape..not selotape
Can I use there d882 transistor ?
No, we need a power mosfet
@@TechIdeasAG Thanks sir
V.V.V.V.V.V.V.V.Very ggood
Sir yasma lm 317 ic lagauda hunxa
No way
I use a D313 & it work's
Antonius Putra its a transistor, or mosfet?
i use a small transistor
With transistor works?
100% work, depends on wire coil number, the more coil winding number bigger result of the plasama light u get
I used a d880 and it was not very powerful, I think it's better with mosfet
I want to meet you... and I want to see how you look in real life!
Oh, really?☺️👍
Yes!!! I have been watching you for a year now... and you have inspired me to create my RUclips channel!!!😁😁
I donr have enough coil can i join two end of a coil
Yes, you can do that but remember to insulate the joint very well
Thank you very much
For reading my coment give you thumbs up
Can u use this as a taser
Yes, ofcourse
I am from police. I want to know your location.
@@physicsisawesome696 jock of a student
@@malluworld3534 I was jocking 😂😂
@@physicsisawesome696 that i said.
I subcribe u just now
No1
I made it exactly like this but it is not working in power of 2 AA batteries(3 V) Do i need 3.7 V..... It is working slow in mobile 3.7 V battery........ Plzzz tell me the POWERSUPPLY
Yes, needs 3.7v to 4.2v for MOSFET. And the MOSFET needs about 1.5 to 2 amps power.
So why mobile battery is not working???? It is 3.7 V. But I don't know how much amps it supply.
Do you have a multimeter? then measure the battery voltage when the circuit is on. It needs to be around 3.7v.
Can I use 👉18650 Battery 2200 mAh 3.7 volt Rechargeable Lithium Cell Li ion battery 2.5 aH
Yes, ofcourse
Awesome but to hard thinks
+Hassan Iad
Thank you.
can i use the 13003 transistor instead mosfet
where is your serkit diagram
chandaneswar bhunia why do you need a schematic for something as simple as this, are you 5?
can it run a cfl of how many watt please tell me
+Prateek banwari
It's not designed to drive a CFL. it's output current is very low but voltage is around 10k.
In my its working but mosfet its very hot
Guys where can i get empty transformer
Shafiq Ahmed Vlogs scrap one from a disposable camera
You can find it in cfl bulb.
Pretty much anywhere. Just boil it in water for like 15 mins and then pull the top and bottom off, then take stuff off the windings and reuse.
i got one from a vhs
l love you 😍😍😍😍😘😘
Or you can just take a mosquito bat's circuit
Mosfet doesnt last long.
You need Heat sink
U did well but u r not a gud tuotier