Very thankful for your video. I followed your video and replaced one wheel on my Ecovacs Ozmo T8. However, during the process of putting it back together, 2 identical springs (4 mmOD x 5mm) accidentally dropped out. I couldn't figure out where they came from so I couldn't put them back. Now when I try to put the vacuum back in service, I get the message that the anti-drop covered with dust. what did i do wrong? Please help!
Good tutorial! I replaced both wheels. But in the first clean robot stopped during the process and is not showing as online. Is it possible to give it to you for service or how to get in touch with you?
I totally just replaced the left wheel on my deebot. Thank you for your excellent tutorial. Did I have a screw leftover that I don't know where it goes? Yes, yes I do. But my deebot is fixed and no longer travelling in circles like a dog chasing its tail. Thank you 🙏
Thanks a lot for the great video! My X1 Omni won’t return to the station as it backs up more to one side. I turned it upside down like you said and I found the resistance between two sides are very minimal. Should I replace the wheels or there’s anywhere I should check? I’ve only used it sparingly for 15 months. Thanks!
Hello, I had issues with my deebot 950 - spinning around all the time. So I checked wheel and it was burnt as you mentioned in video. I replaced wrong wheel and robot is doing well in begining of cleaning, cause Issue still persist after one cycle of cleaning. Replaced wheel is once again stucked. I noticed that off / on always help. Wheel is released and moving normally. But I do not want to do it after each cleaning. Can you help me?
Where can I find a motor assembly for a deebot ozmo t8+? I followed your steps and was able to clean the motor assembly which was very dirty, I also cleaned all the gears and reapplied silicon grease. After putting back i can hear the sound of the motor turning but the gear is not totally in contact with the next gear making a high frequency clicking sound.
Hi, We're very thankful for your videos. We've just replaced the wheels on our ozmo 950 and still getting 'driving wheel malfunction' error. Our front bumper appears to be sticking on the right hand side. Could this be contributing to the error as the device is pushing up against furniture when it errors. Appreciate any advice.
thanks a lot of the video! I managed to open my deebot ozmo 950, but can't put the new wheel back to make it " jumping", could you please suggest how to do it on ozmo 950 model specifically? it is quite different from the one you show? and my be also how to open another wheel? it also looks quite different, at lest on 950. Thanks in advance!
@ecovacstechnicalsupport5278 thanks for this detailed tutorial. I've successfully changed the wheel, and the vacuum is working fine for a little, and then the wheel is stuck again (hard to rotate). I turn it off and on, and then it is working fine again, for few minutes, and then it repeats itself. It seem like I have a bigger issue. What could it be? Is there other component that controls the wheel that might be defective? I would appreciate your help
can someone help me? i while turning it upside down, a small part just fell out of the robot. (t8), it is around a centimeter big and has two square holes in it. it says A4 on the part. i just cant figure out where this part belongs... help :D
Great video, but is there any way to change only the motor? I have soldering skills, but I can't find the same motor anywhere. Do you know any compatible motor for the wheel (do you know voltage and rpm)? Here in my country a complete wheel cost almost half the price of the robot! 😢
Just remove the motor..all details printed outside the motor assembly... motor same is quite difficult..but Carbon brush u can try to replace... hopefully will fix the issue...
Had the same problem! Because it was predominantly moving in a right circular motion, I replaced the R wheel drive (this was suggested in Ecovacs service videos on RUclips). This did not solve the problem however. I then checked the L wheel drive and found one of the two wires leading to the wheel revolution sensor on the L wheel drive had broken. This was resoldered and solved the erratic motion and 'check wheel drive' error. Hope this helps someone.
Hi I ned help on my X1 omni the pad not spinning , looks like some thing are loose, have a video haw to open for ceck inside at X1 omni thanks for help
Yes sure...plz bring at given address...Amara residence block A, floor 19, unit 06. Once reach rhere you have my contact no. Can call me I'll be there to receive
Travi Error 6: Device Stuck or Trapped Device may be suspended in air. Move it to a new position close to the original position and try again. If the device is still unable to start, clean the edge sensor and try again. please help sir
@@ecovacstechnicalsupport5278 hi again i fixed the “please clean my anti drop sensors” after making sure all the wires were connected, but now sometimes the bumper gets stuck
Very thankful for your video. I followed your video and replaced one wheel on my Ecovacs Ozmo T8. However, during the process of putting it back together, 2 identical springs (4 mmOD x 5mm) accidentally dropped out. I couldn't figure out where they came from so I couldn't put them back. Now when I try to put the vacuum back in service, I get the message that the anti-drop covered with dust. what did i do wrong? Please help!
Good tutorial! I replaced both wheels. But in the first clean robot stopped during the process and is not showing as online.
Is it possible to give it to you for service or how to get in touch with you?
ใช้งานดีไหมประเทศไทยไม้มี
Very thankful for your videos!! Congrats!
Welcome
I totally just replaced the left wheel on my deebot. Thank you for your excellent tutorial. Did I have a screw leftover that I don't know where it goes? Yes, yes I do. But my deebot is fixed and no longer travelling in circles like a dog chasing its tail. Thank you 🙏
Thanks a lot for the great video!
My X1 Omni won’t return to the station as it backs up more to one side. I turned it upside down like you said and I found the resistance between two sides are very minimal. Should I replace the wheels or there’s anywhere I should check? I’ve only used it sparingly for 15 months. Thanks!
Hello, I had issues with my deebot 950 - spinning around all the time. So I checked wheel and it was burnt as you mentioned in video. I replaced wrong wheel and robot is doing well in begining of cleaning, cause Issue still persist after one cycle of cleaning. Replaced wheel is once again stucked. I noticed that off / on always help. Wheel is released and moving normally. But I do not want to do it after each cleaning. Can you help me?
Amezing video as usual 👍👍
Welcome
Great video!! Thank you
Where can I find a motor assembly for a deebot ozmo t8+? I followed your steps and was able to clean the motor assembly which was very dirty, I also cleaned all the gears and reapplied silicon grease. After putting back i can hear the sound of the motor turning but the gear is not totally in contact with the next gear making a high frequency clicking sound.
Thanks à lot for this video
I've fixed my wheel problem with it
Hi,
We're very thankful for your videos. We've just replaced the wheels on our ozmo 950 and still getting 'driving wheel malfunction' error.
Our front bumper appears to be sticking on the right hand side. Could this be contributing to the error as the device is pushing up against furniture when it errors.
Appreciate any advice.
Plz WhatsApp me a video clip at 00601137973018...let me see the video then I'll reply...now I'm in hospital for dressing..next is my turn 😅
Super helpfull
Thank you very good video
thanks a lot of the video! I managed to open my deebot ozmo 950, but can't put the new wheel back to make it " jumping", could you please suggest how to do it on ozmo 950 model specifically? it is quite different from the one you show? and my be also how to open another wheel? it also looks quite different, at lest on 950. Thanks in advance!
In this week I'll upload video about Ozmo 950 sir at ur request
that would be awesome, thanks a lot!
@@ecovacstechnicalsupport5278 hello! do you think you will have time to make this video during upcoming days? Thanks and happy new year! :)
Where can we buy the spare parts ?@@ecovacstechnicalsupport5278
@ecovacstechnicalsupport5278 thanks for this detailed tutorial. I've successfully changed the wheel, and the vacuum is working fine for a little, and then the wheel is stuck again (hard to rotate). I turn it off and on, and then it is working fine again, for few minutes, and then it repeats itself. It seem like I have a bigger issue. What could it be? Is there other component that controls the wheel that might be defective? I would appreciate your help
I keep getting the off the floor error message after cleaning my Deebot Neo. Any advise on how to fix?
Hello do you have the goat g1 lawn ? I got a problem with it
Sorry don't have
Good news, now i know to dismantle the wheel. Bad news. I have to open everything 😮😢
can someone help me? i while turning it upside down, a small part just fell out of the robot. (t8), it is around a centimeter big and has two square holes in it. it says A4 on the part. i just cant figure out where this part belongs...
help :D
Great video, but is there any way to change only the motor? I have soldering skills, but I can't find the same motor anywhere. Do you know any compatible motor for the wheel (do you know voltage and rpm)? Here in my country a complete wheel cost almost half the price of the robot! 😢
Just remove the motor..all details printed outside the motor assembly... motor same is quite difficult..but Carbon brush u can try to replace... hopefully will fix the issue...
Because In motor always carbon brush burn that's all
Had the same problem! Because it was predominantly moving in a right circular motion, I replaced the R wheel drive (this was suggested in Ecovacs service videos on RUclips). This did not solve the problem however. I then checked the L wheel drive and found one of the two wires leading to the wheel revolution sensor on the L wheel drive had broken. This was resoldered and solved the erratic motion and 'check wheel drive' error. Hope this helps someone.
Hi I ned help on my X1 omni the pad not spinning , looks like some thing are loose, have a video haw to open for ceck inside at X1 omni thanks for help
For omni X1 not yet done videos...but now soon I'll start about Omni issues
hi, i have checked the driving wheel and none are stucked inside.. may i know if i can send my deevot to tou for fix? thanks
Yes sure...plz bring at given address...Amara residence block A, floor 19, unit 06. Once reach rhere you have my contact no. Can call me I'll be there to receive
Perfect timing since my wheel broke yesterday
Welcome
Boa tarde! Como eu desmonto o n78
So is the only reason the larger battery can't be used in the N8+ is because of the metal weight cover being different?
Not Only the Mattel plate..place of battery also designed accordingly..other models can not fit
where you are ? I am in INDORE want to repair my Ecovacs
Hi..I'm living in batu caves Malaysia..if you are in Malaysia you can contact through WhatsApp 00601137973018
where can i find this wheel?
Please check online sellers like Ali Xpress Amazon etc
Travi
Error 6: Device Stuck or Trapped
Device may be suspended in air. Move it to a new position close to the original position and try again. If the device is still unable to start, clean the edge sensor and try again. please help sir
Plz WhatsApp me a video clip so I can confirm what's the issue...00601137973018
hi i replaced both wheels but now it is saying after i put everything back “please clean my anti dust sensors”
Plz check have you fix the all the wires....or plz check weather sensors got any rust sign...
How to replace anti drop Sensors ... video available.can get help from that
@@ecovacstechnicalsupport5278 ok thank you will try
@@ecovacstechnicalsupport5278 hi again i fixed the “please clean my anti drop sensors” after making sure all the wires were connected, but now sometimes the bumper gets stuck
never mind i fixed it. Thank you so much for these videos. My deebot ozmo 920 is nearly 3 years old now.
P r o m o S M
Just buy another one.🤣😅😂