my bms clip thorn apart can i solder the nickel sheet from battery directly to my metal bms i cannot folding cause it has thorn apart . is it still working
I have an iPhone that will keep showing the old data at 88%, I have tried connecting a different battery, rebooting and reconnecting the new battery with the transfered bms board again but to no avail. The new data won't show up whatever I do, have you come into this? I have done many replacements without issues with the same tag on. Thanks in advance for your reply
you should flash the device which would also flash the battery. You can use 3utools and select quick flash and then once u press flash it would prompt u to flash the battery health percentage which u tick off. Make sure the device is backed up as the flash would erase all data off the phone, and have icloud details on standby for when u restore the phone.
@@phonerepairmaster9787 I'm pretty sure your soldering work isn't strong enough to keep the leads together. When someone drops their phone and the impact causes one of the leads to disconnect you'll have a lot of unhappy customers...
@Phone Repair Master Hello, nice job! can you please confirm if this will work: started with bought a new battery with bms, old battery with original bms coded to iphone. When I switch the bms between them (welded) and connect the new battery with the original bms using jc flex to the phone (cycles 0 and health 100 set to JCID V1S) and then I would use the old battery with the bms from the new battery to reset the phone. And finally connected the new battery with origo bms and jc flex, will it be there 100%? Will this work please? Thanks
With the tag on flex installed and old battery board swapped, boot the phone with an iPhone charging cable. Then after it loads it should show 100% in health. If you do not start the phone with the lighting cable for the first boot it won't work.
I was wondering about that too but i think you need to do it for it to like not read anything cz the batt is dead (the old one). And when he put the new one It can read 100% with no prblm
my bms clip thorn apart can i solder the nickel sheet from battery directly to my metal bms i cannot folding cause it has thorn apart
. is it still working
After i do all of this can i remove the jc flex cable? And will the percentage remain 100?
Yes 100% , no remove jc flex
What is the liquid u used before soldering plz? 12:03
12:23
Soldering acid
What’s the acid name?
I have an iPhone that will keep showing the old data at 88%, I have tried connecting a different battery, rebooting and reconnecting the new battery with the transfered bms board again but to no avail. The new data won't show up whatever I do, have you come into this? I have done many replacements without issues with the same tag on. Thanks in advance for your reply
you should flash the device which would also flash the battery. You can use 3utools and select quick flash and then once u press flash it would prompt u to flash the battery health percentage which u tick off. Make sure the device is backed up as the flash would erase all data off the phone, and have icloud details on standby for when u restore the phone.
@@rtafadar this terms only use on ios 17.4 and above right?
Shouldn't you spot weld the bms? soldering seems kinda risky for the long term.
🤔
@@phonerepairmaster9787 I'm pretty sure your soldering work isn't strong enough to keep the leads together. When someone drops their phone and the impact causes one of the leads to disconnect you'll have a lot of unhappy customers...
Hi, is tag on flex reusable?
Yes
@Phone Repair Master
Hello, nice job!
can you please confirm if this will work:
started with bought a new battery with bms, old battery with original bms coded to iphone. When I switch the bms between them (welded) and connect the new battery with the original bms using jc flex to the phone (cycles 0 and health 100 set to JCID V1S) and then I would use the old battery with the bms from the new battery to reset the phone. And finally connected the new battery with origo bms and jc flex, will it be there 100%?
Will this work please?
Thanks
With the tag on flex installed and old battery board swapped, boot the phone with an iPhone charging cable. Then after it loads it should show 100% in health. If you do not start the phone with the lighting cable for the first boot it won't work.
The blue little board what is it called?
Welding Sleeve Set Battery Repair Clamping
Battery Cable Layout Mold
@@phonerepairmaster9787 thanks
Spot walding ko soldoring iron sa kesa nekal sakta haa ?
Ya too galat ho naa.
Don't understand
Why u used the another battery before??
I was wondering about that too but i think you need to do it for it to like not read anything cz the batt is dead (the old one). And when he put the new one It can read 100% with no prblm
who can i by this
Magnifique 👍
What if you dont have a second battery to false start
then fail to do with procentage
Good
Good job.😊
😊
😮 you should have put plastic on the balancer first and then you forgot to cover it 😂
Bhai mra v battery chense krwana tha ho gyega iPhone 11 k
Bahi aap ka experience kafee kam hai video se pehili ap acha sekli per video banao
I changed mine and didn’t show the percentage is that mean not original?
Yes
Wilson Brenda Thompson Jason Miller Robert
hard to watch...
Now u know why they don't charge just 10€ / battery change.