The hour meter will still count below 1900 rpm, the label was indicating the calculated range per every 60 minutes. It's a mechanical gear train driven counter, so even if it was turning 1rpm, it would eventually register hours.
A thoroughly enjoyable video demonstrating a quality service and Diagnostics for this 1 half-century-old machine! I'm assuming you guys got to tighten that fan belt. Do you have any suggestions for locating a micro excavator in decent condition or even new? Much thanks for all you guys do, be well and abundantly blessed
Correct. It will just take a bit longer to reacht the hour counter up one. 160 hours on the meter shows the engine did 1900 RPM X 160 H X 60 Minutes = 18,240,000 revolutions.
I think the dozer refresh or rebuild videos are the best. I also like how you show the entire process in one video, instead of breaking it up and showing bits as you go. Thanks again for the videos Clint.
Just watching you problem solve and banter with ol' sausage fingers is awesome. Your ability to problem solve equipment is impressive Clint, love your channel!
I’m a retired mechanic, (not heavy equipment). At 70 I’ll likely never operate a dozer, let alone need to work on one. Yet I still love watching and learning from Clint and the boys. Crazy or what??
I love how you are teaching young Mason along with Hunter and Tucker, you and Kevin have a ton of knowledge between you so if he pays attention he should do quite well for himself in life, thanks for the video Clinton. I think around your state most heavy equipment users would watch your channel just to see what they can buy and just how good it is, I know I would.
@ My Cancer Journey I hope you have success in your fight with Cancer and your You Tube Channel, my wife has lung cancer and fought ovarian cancer and was surgically cleared, so keep your hope up she would not let it beat her and is so far still staying strong against the lung cancer.
Cancer is a three bladed problem. The state of California has a list of things that cause cancer and birth defects. Vitamin D the sunshine vitamin regulates each of the energy producing mitochondria in each cell. The last is body charge. -10 mev is goal. You can get sheets that ground you, put bear skin on wet soil, grab hold of a tree, get in salt water, or exercise really hard like your near puking. If you are off in any area cancer can start! 2 and it can spread!
I believe the hour meter will read no matter what the RPM is. It's just that at 1900 RPM for 60 minutes it works out to an hour on the meter. If it ran at 1700 RPM it may have to run for 65 minutes to make an hour on the meter.
Likely the opposite. Lower RPM should turn the meter slower and higher RPM turn the meter faster. Makes sense as the meters a measure of engine usage, and higher RPM's equal more "wear", and more frequent PM's. The meter could internally calculate that.
@@ravenbarsrepairs5594 The meter works off of a geared system that has an "X" number of revolutions equaling one hour. It doesn't matter how fast or slow the engine is turning, the number of revolutions that equals one hour on the meter stays the same. At 1900 RPM's, the meter just happens to turn over one hour in sixty minutes. A slower RPM than 1900 and the meter will turn over one hour in over 60 minutes, a higher than 1900 RPM and the meter will turn over an hour in less than 60 minutes.
@@armyranger9346 I don't think you quite understand how the meter works. if you are running less than 1900 rpm it will take longer than 1H to get a 1count on the service meter. all the tag said is at 1900 rpm 1 unit of the service meter is equal to 1H. if you idle for 2H at 950 rpm you will see only 1 unit on the service meter.
@@mog5858 Read my posts. That is exactly what I said. 1900 RPM for 60 minutes (one hour) equals one hour on the meter. 1700 RPM (slower RPM) may take 65 minutes (one hour and five minutes) to show one hour on the meter.
omg.. kevin's remark at the front... "all that cat *oop" i spilt my coffee lmao .. i love this channel! perfect blend of timelapse, work, explanations and humour. thanks as always Clint!
I wish people selling used vehicles would be as conscientious as you guys... the world would be a better place! Thank you for all you do and showing the world how it should be done! 👏🏽 👍🏼☺ Keep'em Coming!
These kinds of videos are the best, from the purchase, to C&C's always diligent (no short cuts!) works, to (what is usually an immediate) sale of a great machine! Well done Clint, Kevin and the boys. Hopefully we get to see it going to its new owner and of course seeing the results of "Randy's Valet Shop" too !
Clint, your diagnostic skills are incredible. back in my day we didnt have computerized anything. It took experience. diagnostic skills like listening to moving parts with a large screw driver in your ear. We shifted our gears in the 10 speeds by the pyrometer. How about your metallurgical skills? They're perfect. Being able to see a product that has to be made then actually making and installing it is extraordinary. I wished I'd have a plasma cutter, we cut everything with a torch
When Kevin said he wasn't pregnant, I nearly spilt my coffee. 🤣😂🤣 Shame they didn't leave that dozer blue in the navy colour, would have liked so smart. Nice job again Clint, always look forward to you dozer re builds. 👍🤗
That D7F seems like it is a pretty nice machine. It looks like it hasn't been abused or butchered. The panels all seem pretty straight and it doesn't look like it has had a bunch of popcorn weld repairs.
Clint, you guys may not be Kitty Cat mechanics but you're sure working towards becoming one. I really enjoy your episodes when Y'all work on them. Nice to see Mason working with you getting some shop learnin' and experience. Whoever buys that Cat can rest assured it's gonna be reliable as usual. C & C definitely goes beyond a cheap pain job. It ain't leaving your shop unless it's 100 percent dirt moving ready.
I love this D 7 repairs. This is a testament to your auction knowledge. This Cat is going to make someone a very nice machine. Your business will always grow because customers trust you and that’s the best advertising you can get.
Re hour meter, back in the 1950s, neighbor had an IH British built Diesel tractor with the same type of hour meter on the injection pump and it was clocked to the engine running at 1650 RPM which was the engine speed that gave the standard 540 PTO RPM. So if you ran the tractor engine at 1650 RPM the hour meter would record 1 hour for every clock hour. Run the engine at a slower RPM the hour meter would take more than 1 clock hour to record an hour, faster than 1650 RPM would record more than 1 hour in a clock hour.
The most importent always is: Gaskets, oil & filters + clean fuel and now howe, then & do it All the time! Bigger engine even moore important! From Peter Eriksson Sweden Europe 😊😊😊! A good Turbo guy is Not bad either to have in house, or.....?😊😊😊 we have Super Turbo guy, Glenn you are No 1 in Sweden! 😊😊😊
Actually they weren't that good of a machine, I'd sooner have a D7E or a G. That 6 cylinder motor lead to lots of transmission and final drive failures. My dad owned 8 D7E'S and 2 F's, once warranty ran out he got rid of the F's
I love seeing these big dozers. The fact that they are retired military makes it even better. I’d love to see one in fresh blue paint! Great video as always.
Those were a good old machinery! My old boss he hade a d8 and a 9 . Both were Good units. I was 15 then and I thought they were huge. Learned alot form him. Good guy! Love your vids clint
…this is a fantastic machine C&C • whoever buys it will have huge benefit from and through it • point being, its a reliable and rock solid piece of engineering ~ not too big, most definately NOT too small, just dead right in power to weight configuration Gotto have a ripper attachment fitted though, for to be a complete unit⁉️ Thanks again really enjoyed this view To follow each additional step of the way ex ZA…👊❗️ 🔥 🥂 🪖
Keep doing what your doing, I really enjoy your videos,, you letsdig, and dirt perfect are my go-to videos if I want to see informational videos, like yours since I was a mechanic for 40 years, the new stuff kicks my ass
I live right by where you went to get parts for that CAT. My mom was a project manager on that site when they built it. Pretty awesome facility really.
What’s the blood wound on the left side of your head by your eye bud? 🤔 Hi from Texas “momma” CEO! The boy did not say yes ma’am did he? Be thankful she didn’t use a cast iron skillet like ours do. Always enjoy your videos. Keep it coming and hi from Texas
I think in my opinion you should paint it back to navy blue it would look very cool but that's just me I love watching you all keep up the great work and videos
C&C Equipment +: Have been 'out-of-pocket' for a wee bit here, so... That said, another of this channel's excellent videos, as is almost always the case. Accordingly, it earns the standard _YT_ 'thumbs-up' ree-ward . These are always looked forward to and enjoyed. Well done, guys! And keep 'em coming!
Why not purchase from auctions if you have opportunity and knowledge Clints knowledge brings old & new back original if not better conditions. Brother-in-law learned his knowledges in marine core.. Tech from American Airlines called him help trouble shoot repair. He is heavy mechanic, not airplane tech. Clint your best!
Since it used to be Navy how about painting it back Navy and none of that sand crap. I think you know what I mean that weird off blue color 1 color paint. Just looked it up Navy Seabee color that covers vietnam-era to the 90s, someone mentioned a glossy green. Check it out again that was off somebody's Business site.
The knuckles where the blade and the push arms come together are backwards. The push arm pin should be in front of the blade pin. That’s why blade angle is way off.
The F350 looks good I finally got the F350 Dually home I bought over a month ago I’m going to be sending the injection pump out to area Diesel service to get them to work there magic
Maybe a very Late F cross over to a G There are some 977L's which have outboard Top Roller Turrets as the former 977K's had , these were late K's crossover to L's
Interesting bluish color. I was not in the Seebee's but that almost looks like a Navy machinery gray color. Machinery gray had a blueish tint that we used on pumps and other equipment in the fireroom.
No that is simply the rpm that the counter is calibrated to. It still reads at low rpm but at a lesser rate. After being a Cat dealership mechanic and working 20 years as a heavy eq. lead mechanic, I remember why I am grateful for retirement.
I think the blue paint might be Air Force blue. I was in the Navy Seabees, and we used to get Air Force hand me downs all the time. They would get the new equipment, and the Seabees would get their old junk.
Clint, since its made in england, it might be hours measured in British units.. hence hours and times different in their measuring.... I know a hour is a hour but it may be their way of measuring it. So its still measuring the hours but say its ran at fifteen hundred rpms instead of nineteen hundred rpms, that number would take longer for the hour meter to register the hour. As I say that, it makes no absolute sense as to a hour being a regular hour of wear. This is just a guess
If you remember back in the auction when they got it started, they got it started on the can once you get started on the can it’s hard to come down from it and cats are known to huff lol
The biggest thing I see is that if anyone buys a piece of equipment from you they can be confident it is the best they can get. 😊
Damn skippy
Just ask perfect dirt I mean dirt perfect lol! Because of him we have your channel or I’m here
You guys put a lot of effort into your repairs and it shows you care to sell a good product!
The hour meter will still count below 1900 rpm, the label was indicating the calculated range per every 60 minutes. It's a mechanical gear train driven counter, so even if it was turning 1rpm, it would eventually register hours.
I was thinking along similar lines myself…thanks for that. 👍🇺🇦👍🇺🇦
Agree.
A thoroughly enjoyable video demonstrating a quality service and Diagnostics for this 1 half-century-old machine! I'm assuming you guys got to tighten that fan belt.
Do you have any suggestions for locating a micro excavator in decent condition or even new?
Much thanks for all you guys do, be well and abundantly blessed
Correct. It will just take a bit longer to reacht the hour counter up one. 160 hours on the meter shows the engine did 1900 RPM X 160 H X 60 Minutes = 18,240,000 revolutions.
@@roelrobbers7004 I agree (within non-fractional quantities)
I think the dozer refresh or rebuild videos are the best. I also like how you show the entire process in one video, instead of breaking it up and showing bits as you go. Thanks again for the videos Clint.
Glad you like them!
Just watching you problem solve and banter with ol' sausage fingers is awesome. Your ability to problem solve equipment is impressive Clint, love your channel!
I’m a retired mechanic, (not heavy equipment). At 70 I’ll likely never operate a dozer, let alone need to work on one. Yet I still love watching and learning from Clint and the boys. Crazy or what??
I love how you are teaching young Mason along with Hunter and Tucker, you and Kevin have a ton of knowledge between you so if he pays attention he should do quite well for himself in life, thanks for the video Clinton. I think around your state most heavy equipment users would watch your channel just to see what they can buy and just how good it is, I know I would.
@ My Cancer Journey I hope you have success in your fight with Cancer and your You Tube Channel, my wife has lung cancer and fought ovarian cancer and was surgically cleared, so keep your hope up she would not let it beat her and is so far still staying strong against the lung cancer.
Cancer is a three bladed problem. The state of California has a list of things that cause cancer and birth defects. Vitamin D the sunshine vitamin regulates each of the energy producing mitochondria in each cell. The last is body charge. -10 mev is goal. You can get sheets that ground you, put bear skin on wet soil, grab hold of a tree, get in salt water, or exercise really hard like your near puking. If you are off in any area cancer can start! 2 and it can spread!
I believe the hour meter will read no matter what the RPM is. It's just that at 1900 RPM for 60 minutes it works out to an hour on the meter. If it ran at 1700 RPM it may have to run for 65 minutes to make an hour on the meter.
Likely the opposite. Lower RPM should turn the meter slower and higher RPM turn the meter faster. Makes sense as the meters a measure of engine usage, and higher RPM's equal more "wear", and more frequent PM's. The meter could internally calculate that.
@@ravenbarsrepairs5594 The meter works off of a geared system that has an "X" number of revolutions equaling one hour. It doesn't matter how fast or slow the engine is turning, the number of revolutions that equals one hour on the meter stays the same. At 1900 RPM's, the meter just happens to turn over one hour in sixty minutes. A slower RPM than 1900 and the meter will turn over one hour in over 60 minutes, a higher than 1900 RPM and the meter will turn over an hour in less than 60 minutes.
@@armyranger9346 I don't think you quite understand how the meter works. if you are running less than 1900 rpm it will take longer than 1H to get a 1count on the service meter. all the tag said is at 1900 rpm 1 unit of the service meter is equal to 1H. if you idle for 2H at 950 rpm you will see only 1 unit on the service meter.
@@mog5858 Read my posts. That is exactly what I said. 1900 RPM for 60 minutes (one hour) equals one hour on the meter. 1700 RPM (slower RPM) may take 65 minutes (one hour and five minutes) to show one hour on the meter.
Good afternoon guys
omg.. kevin's remark at the front... "all that cat *oop" i spilt my coffee lmao .. i love this channel! perfect blend of timelapse, work, explanations and humour. thanks as always Clint!
Glad you enjoy it!
Keep the "Old Iron" coming boys , we love it .👍🇭🇲
I wish people selling used vehicles would be as conscientious as you guys... the world would be a better place!
Thank you for all you do and showing the world how it should be done! 👏🏽 👍🏼☺
Keep'em Coming!
These kinds of videos are the best, from the purchase, to C&C's always diligent (no short cuts!) works, to (what is usually an immediate) sale of a great machine! Well done Clint, Kevin and the boys. Hopefully we get to see it going to its new owner and of course seeing the results of "Randy's Valet Shop" too !
I have watched every episode of the show u put out from the start up to date
Somebody bought a really good dozer. Those older caterpillars, they are the best.
Clint, your diagnostic skills are incredible. back in my day we didnt have computerized anything. It took experience. diagnostic skills like listening to moving parts with a large screw driver in your ear. We shifted our gears in the 10 speeds by the pyrometer. How about your metallurgical skills? They're perfect. Being able to see a product that has to be made then actually making and installing it is extraordinary. I wished I'd have a plasma cutter, we cut everything with a torch
Thanks for reading my comment and responding. I know you must be busy. God bless you and your family and friends
When Kevin said he wasn't pregnant, I nearly spilt my coffee. 🤣😂🤣 Shame they didn't leave that dozer blue in the navy colour, would have liked so smart. Nice job again Clint, always look forward to you dozer re builds. 👍🤗
That D7F seems like it is a pretty nice machine. It looks like it hasn't been abused or butchered. The panels all seem pretty straight and it doesn't look like it has had a bunch of popcorn weld repairs.
Nice job guys as always. They just don't make them like that anymore.
Clint, you guys may not be Kitty Cat mechanics but you're sure working towards becoming one.
I really enjoy your episodes when Y'all work on them.
Nice to see Mason working with you getting some shop learnin' and experience.
Whoever buys that Cat can rest assured it's gonna be reliable as usual.
C & C definitely goes beyond a cheap pain job.
It ain't leaving your shop unless it's 100 percent dirt moving ready.
I love this D 7 repairs. This is a testament to your auction knowledge. This Cat is going to make someone a very nice machine. Your business will always grow because customers trust you and that’s the best advertising you can get.
Wow! I’ve finally found a true mechanic that doesn’t wear latex gloves! And doesn’t mind getting his hands dirty!
Love them old D7 and D 8s love to see them get a litter love.. They built The Interstate highway systems 🎉🎉🎉
Re hour meter, back in the 1950s, neighbor had an IH British built Diesel tractor with the same type of hour meter on the injection pump and it was clocked to the engine running at 1650 RPM which was the engine speed that gave the standard 540 PTO RPM. So if you ran the tractor engine at 1650 RPM the hour meter would record 1 hour for every clock hour. Run the engine at a slower RPM the hour meter would take more than 1 clock hour to record an hour, faster than 1650 RPM would record more than 1 hour in a clock hour.
The most importent always is: Gaskets, oil & filters + clean fuel and now howe, then & do it All the time! Bigger engine even moore important! From Peter Eriksson Sweden Europe 😊😊😊! A good Turbo guy is Not bad either to have in house, or.....?😊😊😊 we have Super Turbo guy, Glenn you are No 1 in Sweden! 😊😊😊
Funny I had been watching you guys and didn’t realize you were located in Indiana. Until I saw MacAllister in the into. I’m a tech in the shop.
Another great video... gettin' close to 100K!
So close!
Ready for another 50 years of service!
Very interesting to watch these older pieces of equipment being made ready for sale. Good to see too, that you run an truly honest Company Clint.
Great video Clint. The old D7F were bullet proof. Great machine to operate.
Actually they weren't that good of a machine, I'd sooner have a D7E or a G. That 6 cylinder motor lead to lots of transmission and final drive failures. My dad owned 8 D7E'S and 2 F's, once warranty ran out he got rid of the F's
Clint - your knowledge is amazing rebuilding the old iron! Love watching you guys! Jim
I love seeing these big dozers. The fact that they are retired military makes it even better. I’d love to see one in fresh blue paint! Great video as always.
That cat came from the Navy Blue Angel's in Pensacola Florida. Home of the blue Angel's..you have a rare pcs. Of history there..
Time to do a C&C Service and bring this king back to life. Still has a 100 years of working life in it👏👍
Congratulations on reaching 100k subscribers! Well done Clint.
Those were a good old machinery! My old boss he hade a d8 and a 9 . Both were
Good units. I was 15 then and I thought they were huge. Learned alot form him. Good guy! Love your vids clint
Always hit the like button for great videos!! Thank you for bringing us along on your journey!!!
Our pleasure!
That's one sweet kitty! Another great auction find - even though it needs a little TLC. It's in the right place for that. 👌
It's yellow (very) and not quite ordinary but Clint and Kevin are here and the old machine will come back to life.
That’s a nice dozer love the old iron y’all do great work c&c mint 👌🏼
…this is a fantastic machine C&C
• whoever buys it will have huge benefit from and through it
• point being, its a reliable and rock solid piece of engineering
~ not too big, most definately NOT too small, just dead right in power to weight configuration
Gotto have a ripper attachment fitted though, for to be a complete unit⁉️
Thanks again
really enjoyed this view
To follow each additional step of the way ex ZA…👊❗️
🔥
🥂
🪖
Keep doing what your doing, I really enjoy your videos,, you letsdig, and dirt perfect are my go-to videos if I want to see informational videos, like yours since I was a mechanic for 40 years, the new stuff kicks my ass
I live right by where you went to get parts for that CAT. My mom was a project manager on that site when they built it. Pretty awesome facility really.
Well, I’m home sick. I feel like crap watching your video makes the time go by a lot faster.
Get better soon
I'm really impressed with your knowledge of all these different cat machine.
Excellent video in typical C&C fashion. Love this type of content.
Another great video! Love to see those old Cats.
At 44 minutes it's sound pretty good running! From Peter Eriksson Sweden Europe 😊😊😊!
What’s the blood wound on the left side of your head by your eye bud? 🤔 Hi from Texas “momma” CEO! The boy did not say yes ma’am did he? Be thankful she didn’t use a cast iron skillet like ours do. Always enjoy your videos. Keep it coming and hi from Texas
4:15 the HP fuel pump has left the chat
5:36 quick squirt of love juice
5:40 HP fuel pump back in chat
it's good when spare parts are at hand!!!!
Dang. That's a really sweet machine. Another job. Well Done. OUTSTANDING 🇺🇸
I think in my opinion you should paint it back to navy blue it would look very cool but that's just me I love watching you all keep up the great work and videos
I would have loved to have started working at a place like this after highschool and learned everything and then start my own business later in life
Really enjoy your Auction trip's, & enjoy seeing what you get, even other's benefit from your Knowledge of machinery.
Thanks 👍
100 thousand is getting close. Pretty nice tractor.
Sure is!
Nice old cat, they sure sound good. Keep smilin
Nice machine and I really like the sound of that engine. It still sounds new!
Freaking awesome video thank you love any and all your content fantastic channel
Agree with you
Boy do I miss Tennessee!👍🇺🇸
Clinton and Kevin great video! Thanks for sharing! Kevin
Thanks for watching!
C&C Equipment +: Have been 'out-of-pocket' for a wee bit here, so...
That said, another of this channel's excellent videos, as is almost always the case. Accordingly, it earns the standard _YT_ 'thumbs-up' ree-ward .
These are always looked forward to and enjoyed. Well done, guys! And keep 'em coming!
Really Glad Mike Simon gave you a Shout-out !!
Even though he Drives Chevys and Uses Black and Decker Tools !!! LoL !!
Paint it Navy blue on the way out the door!
Why not purchase from auctions if you have opportunity and knowledge Clints knowledge brings old & new back original if not better conditions. Brother-in-law learned his knowledges in marine core.. Tech from American Airlines called him help trouble shoot repair. He is heavy mechanic, not airplane tech. Clint your best!
You guy knows your stuff. It’s fun to watch.
Congratulations on reaching 100k!
Thank you!!
looks like boss got ahold of you clint
Yep
If I were buying a used dozier and all of your repairs are like i saw on your channel I would surely buy from you.
Love them old girls would love to get one one day will have to make do with my old d6b for the time being love watching your channel
Thanks for a good show
Our pleasure!
Since it used to be Navy how about painting it back Navy and none of that sand crap. I think you know what I mean that weird off blue color 1 color paint. Just looked it up Navy Seabee color that covers vietnam-era to the 90s, someone mentioned a glossy green. Check it out again that was off somebody's Business site.
The knuckles where the blade and the push arms come together are backwards. The push arm pin should be in front of the blade pin. That’s why blade angle is way off.
Another GREAT video, you guys work your magic fer sure !!
God job
Kev's purse hand got the best of that old drain plug.
I really enjoy watching the old Cat dozer videos !!
Great job servicing the cat guys
The F350 looks good I finally got the F350 Dually home I bought over a month ago I’m going to be sending the injection pump out to area Diesel service to get them to work there magic
Good deal
Be sure to mention us
Maybe a very Late F cross over to a G
There are some 977L's which have outboard Top Roller Turrets as the former 977K's had , these were late K's crossover to L's
Great job fixing the rams guys
That is a nice dozer now that it has been 100% serviced nice purchase!👍🏻✅👍🏻
Congratulations on 100K Subscribers! Well Deserved!
You sure know your machines and you know how to pick 'em at the auction. Well done.👍
Thanks 👍
Great video Clint and crew
Really enjoy watching your videos !
Interesting bluish color. I was not in the Seebee's but that almost looks like a Navy machinery gray color. Machinery gray had a blueish tint that we used on pumps and other equipment in the fireroom.
What a nice old machine. Wish i could buy it.
No that is simply the rpm that the counter is calibrated to. It still reads at low rpm but at a lesser rate. After being a Cat dealership mechanic and working 20 years as a heavy eq. lead mechanic, I remember why I am grateful for retirement.
Good show Kevin tell Clint you want to rebuild a D10 cat
If you have honesty and integrity, nothing else matters. Looks like it would be worth the drive to buy equipment at C&C!
You would not believe how much I miss operating and being around the old equipment Thanks for showing it
Dang, that's a real nice looking black Ford pickup. Very nice purchase on the D7 that's a really clean tractor👍
Looks brand new
Like to see it in the Navy colors...
You boys do good work !
I think the blue paint might be Air Force blue. I was in the Navy Seabees, and we used to get Air Force hand me downs all the time. They would get the new equipment, and the Seabees would get their old junk.
Fascinating content. Oil and filters on a grand scale.
Clint, since its made in england, it might be hours measured in British units.. hence hours and times different in their measuring.... I know a hour is a hour but it may be their way of measuring it. So its still measuring the hours but say its ran at fifteen hundred rpms instead of nineteen hundred rpms, that number would take longer for the hour meter to register the hour. As I say that, it makes no absolute sense as to a hour being a regular hour of wear. This is just a guess
Love dem CATs!!!! Thanks Clint. Ye Ole Caterpillar Cowboy
I like the fact you always have a manual on the tractor your working on , let’s folks that buy it know its done right….
If you remember back in the auction when they got it started, they got it started on the can once you get started on the can it’s hard to come down from it and cats are known to huff lol