How to replace the clutch on a 2014 Chevy spark, with out pulling the engine!!!
HTML-код
- Опубликовано: 8 сен 2024
- In this video I'm going to show you how to remove the clutch in you 2014 Chevy spark, thanks for watching.
i am not liable for anything that happens or occurs while you are working on your vehicle, this video is only for a entertainment , and you may need more information to properly do the work. I am not liable for any injuries or death due to your work done on your vehicle done at your own risk
check out the facebook
/ fixergood351w
Great video! Only tip, axles DO NOT have to come out of the hub, just pop them out and hang them with a ratchet strap. Saves the trouble of having to mess the axle nut 😊
thanks for watchin really apreciate it, and the tips
Thanks for this video it was a help.
R.E About the drive shafts; Use two screwdrivers 180 degrees apart and wiggle from side to side until it pop's. Even better is the screwdriver type pry bar with the bent end on it. Two of these work great.
Also try not to pry on one side of it as it binds it up even worse.
Thanks for watchin glad it was helpfull br sure to like and sub for more tips and tricks.
Thank you for the great video, correct model in the description, is very clear. It is so time-consuming having to search through incorrectly named descriptions, such a pleasure to find videos like yours. Makes me want to know more, lol.
The question on my mind now is, if the centre clutch bearing is incorrectly seated cause a whine on the gearbox, even a rumble/grind when driven, stops when the clutch pedal is put in?
And should there be a noise when the clutch pedal is up, but stops when you put peddle in?
if you have a rumble noise it sounds like a bearing of some sort, usually I wheel bearing makes this kind of noise
@@fixergood pilot release bearing?
Wheel bearings were done a year agp
This video was super helpful for me since no one appears to offer an aftermarket teardown book for this car.
Does anyone know how to replace the Gear oil, the video doesn't cover it, and I'm kinda at a loss?
Thanks!
I'm not sure I did not drain the oil on mine, on some models you take the reverse sensor out and fill from there but I'm not sure thanks again fir watchin.
Very helpful thank you very much
Thanks for watchin besure to like and subscribe fir nore tios and tricks
About how many miles did you have on the factory clutch? And how did you know you needed a new clutch? Just trying to get a ballpark of when to change my Chevy Sark clutch. Thanks for the video, earned a new Subscriber!
Thanks really apreciate it I think it had 90,000 on it but it all depends on the driver, some clutches last 200,000 miles it just depends. For the most part you'll get a heads up before it goes out like it slips in 4th gear, or it gets stuck in gear. Thanks again.
Right now my Chevy Spark 2013 manual 1.2L is at the mechanic workshop.
he said that the Flywheel needs rebalancing smoothing by chiseling it.
also , he is replacing my clutch disc and pressure plate to one that is called PHC Valeo Kit and he said that it is even better than the factory one that i have right now who's manufactured in china.
i wanted to ask what do you think about the claim that the Valeo kit is better than the factory one , and also what is the name of the factory that makes the original one.
Thank you !
Was there a certain way to put the tone ring back in I am having a problem with the crank sensor not working now after a motor change.
The tone ring is part of the of the flywheel and its keyed to fit a certain way on the crank shaft. If you did a engine swap from a diffrent year its possable the tone ring is diffrent qhich they like to change alot. Thanks for watchin really apreciate it.
@@fixergood thanks so much I was told it was the exact same year it looks identical except the new motor had some kind of spacer on the crank shaft where the flywheel went I just assumed it was maybe for a automatic transmission but I didn’t reuse it because my flywheel for the clutch wouldn’t bolt up with it. Maybe that’s my problem idk
How long did it take in the end
Took me 5 hours, 1 hour was just on the starter motor 🤣
In this video of the 2014 manual clutch replacement: DID you find it easier to remove without taking the engine and the tranny out? or did it take the same estimated time? Thanks for the video Very helpful
I did it this way because when you remove the engine asembly it books at like 12 hrs.thanks for watchin really apreciate it.
What is the reason for removing thr shift fork shaft
Great info, Fck that I'll leave it on the side of the road😂
Thanks for watchin
Would this process work for 2013 Chevy Spark Manual Trans?
I'm not sure but I would assume so thanks for watching and besure to like and subscribe , thanks again for watching.
@@fixergood Thank You Sir, Keep up the awesome work
Just about to do one now 🙈 without a ramp/lift.
How long did it take doing it your way. I might just drop the engine.
Yes same thing
Hey! Do you maybe have any tips on how to remove the starter motor? I need to change it on a chevy spark 2011 but I cant reach the bolts from under or above the spark engine 😅
From underneath, use 1/4 drive ratchet and extension
Chevrolet Cruze 2012 manual transmission 6speed clutch kit what diameter
how to you bleed the clutch
2006 Chevy spark clutch vibrates when you change gears, what could that be?
so I don't think I should attempt this with no real tools, no shop, and no experience. Mine needs a new clutch...
thanks for watchin it is a big job
never did show how to change the throw out bearing
seeing the sonic has a hydraulic clutch im surprised to see a non hydraulic setup in the spark.
yeah it's interesting they would choose too use older tech for somthing like that, but maybe its lighter and gives better mpg's .
Then why does he mention and show a "slave cylinder" at 3:38?
@@phiksit its not part of the throw out bearing like it is on my sonic, so if you just have a slave cylinder issue its an easy fix on this spark.
That was automatic or manual transmision?
It was a manual transmission, thanks for watchin
@@fixergood i am going to change one on monday for the same 2014 model. Thank you for video!
How do you know the clutch plate went out and what codes came up
I've never had a code come up for a clutch going bad, or usually you can tell it's bad by it slipping in 4th gear and not moving very well or smelling like burnt clutch.
Thanks for watchin really appreciate it , besure to like and subscribe for more tips and tricks and check out facebook and instagram and give it a like for more help in the future
Very difficult to follow
stop the talk n go do it,,,,,
You skipped over the part where the throwout/release bearing was such a giant cluster F to get back in. The other influencers did as well. Now we know why. 2 hours and a f ton of mollt grease later. Still going. How did you get past it?
Personally didn’t have issue with mine? Came on and off in less than a minute.
If you are going to make instructional video. Make the entire process, especially don't emit the video parts please. Makes this useless.
Very helpful thank you
thanks for watchin really appreciate it.