Badass build! Thx for sharing your build secrets. Also like your explanations on everything as I'm still learning my RC Craft. I was looking at that rear link riser and you convinced me its worth trying.💚👍👌🤙
Pretty simple. A friend of mine gave 1/4" nitro fuel line. I measured the correct distance that the driveshaft needs to be and I cut some fuel line for both sides to make it correct length. If you take the driveshaft out, the middle metal piece slips out. Just cut 2 equal pieces on both sides and put that into the driveshaft then insert the metal piece, and install it.
Awesome build.....I'm doing an element based v3 next and might put a element trans in my current rig because I think I like brushed systems better than outrunner I'm using but will see.
Thanks a ton for such detailed description of your rig. This definitely will help me with mine. I have a question about the piece you’re using in the rear part to rise the links connection/bolt…what is this for??? Thanks again
Thanks for checking out my build video. The rear upper link riser changes the geometry of the rear links. By positioning the rear upper links higher, it helps to increase anti-squat, meaning that the front tires will stay planted a bit longer, and thus giving my Enduro more front end bite when climbing. On a steep climb, as you press the throttle, the rear wheel will push down, thus lifting the front end. The geometry change helps the front stay planted a bit more.
Unless you want absolute best performance, other options might be better. Check out this video where I compared it to Element Stealth-X transmission with 25% OD installed vs. 2.Low. ruclips.net/video/OGpoH_FdAxc/видео.html
Few questions. Will scx10 and stealth x go on same skid plate? And I’m either gonna buy sendroHD, or builders kit?????? Can’t pull trigger what you think brother. Is it worth the $125 for electronics, body and wheels???? I’m thinking not. But just can’t decide.
Great question. I believe the SCX10.2 and Element Stealth X use the same bolt pattern so they are interchangeable...but I am not sure on SCX10.1, so might want to confirm...I believe they use the same but will be good to check. Since you are building a custom rig, I would recommend the builder's kit and you can add electronics of your choice...if going for cheaper build, just use HW1080 ESC and HH Crawlmaster Sport 550 in either 10T or 12T, you should be good to go. A cheaper brushless setup might be going with HW Fusion 1800kv. Good luck.
Hi bro...i need your opinion... Im planing to get a element enduro builders kit 2 as a donner to gspeed chassis... Is it worth...? And how about the plastic gear on stealth x transmission...is it durable?
It’s a great way to go. I have never had any issues with plastic gears. It’s been fool proof for me. When my friends were getting into LCG, I told them to pick up Enduro Builders Kit. Build with regular chassis, then mod it to their delight. Run it for a while, then do the gspeed conversion to really see the difference. This is a great way to go in my opinion and now they fully understand the performance gained. Good luck with your build.
love seeing that notification of a new BigSung Hobbies upload 🥳🙌🏻
Thanks and more to come ;)
Also, next upgrade.. for science.. put a small, lightweight outrunner..
This build will stay brushed setup, so no outrunner. My future builds will have brushless setup though.
nice job! i just finished my enduro but now i want a gspeed.
You should! It definitely takes Enduro to next level of performance.
A big THANKS As I'm building pretty much the same rig. This answered a few questions that I had. Great job on the vid.
BG from Alberta
You are welcome, and glad to hear that the info will be helpful.
Awesome! Great information.
Glad it was helpful!
Badass build! Thx for sharing your build secrets. Also like your explanations on everything as I'm still learning my RC Craft. I was looking at that rear link riser and you convinced me its worth trying.💚👍👌🤙
Thanks 👍 and you are welcome! It's definitely worth trying out.
Looks like a nice setup. Thank you for sharing.
Thanks, and hopefully it will help with your setup.
Sung.. I need to understand your trick for extending the driveshafts
Pretty simple. A friend of mine gave 1/4" nitro fuel line. I measured the correct distance that the driveshaft needs to be and I cut some fuel line for both sides to make it correct length. If you take the driveshaft out, the middle metal piece slips out. Just cut 2 equal pieces on both sides and put that into the driveshaft then insert the metal piece, and install it.
@@BigSungHobbies Hell yeah thank you
Awesome build.....I'm doing an element based v3 next and might put a element trans in my current rig because I think I like brushed systems better than outrunner I'm using but will see.
Thanks! Brushed works well, and you can't go wrong with Element based build.
Thanks a ton for such detailed description of your rig.
This definitely will help me with mine. I have a question about the piece you’re using in the rear part to rise the links connection/bolt…what is this for???
Thanks again
Thanks for checking out my build video. The rear upper link riser changes the geometry of the rear links. By positioning the rear upper links higher, it helps to increase anti-squat, meaning that the front tires will stay planted a bit longer, and thus giving my Enduro more front end bite when climbing. On a steep climb, as you press the throttle, the rear wheel will push down, thus lifting the front end. The geometry change helps the front stay planted a bit more.
@@BigSungHobbies thank you so much!!!!
I'm going to have to try soa at somepoint!
You should. I really like SOA for this build.
Awesome video,,great information,,I want a 2 low trans but I do not comp ,,I like your advise sir!
Unless you want absolute best performance, other options might be better. Check out this video where I compared it to Element Stealth-X transmission with 25% OD installed vs. 2.Low. ruclips.net/video/OGpoH_FdAxc/видео.html
Few questions.
Will scx10 and stealth x go on same skid plate?
And I’m either gonna buy sendroHD, or builders kit??????
Can’t pull trigger what you think brother.
Is it worth the $125 for electronics, body and wheels???? I’m thinking not.
But just can’t decide.
Great question. I believe the SCX10.2 and Element Stealth X use the same bolt pattern so they are interchangeable...but I am not sure on SCX10.1, so might want to confirm...I believe they use the same but will be good to check. Since you are building a custom rig, I would recommend the builder's kit and you can add electronics of your choice...if going for cheaper build, just use HW1080 ESC and HH Crawlmaster Sport 550 in either 10T or 12T, you should be good to go. A cheaper brushless setup might be going with HW Fusion 1800kv. Good luck.
Thanks so much!!
Knew where to go for in depth advice and how to.
🍻🙏
Glad that I can help out.
Hi bro...i need your opinion... Im planing to get a element enduro builders kit 2 as a donner to gspeed chassis... Is it worth...? And how about the plastic gear on stealth x transmission...is it durable?
It’s a great way to go. I have never had any issues with plastic gears. It’s been fool proof for me. When my friends were getting into LCG, I told them to pick up Enduro Builders Kit. Build with regular chassis, then mod it to their delight. Run it for a while, then do the gspeed conversion to really see the difference. This is a great way to go in my opinion and now they fully understand the performance gained. Good luck with your build.
Thanks for the advice bro...btw love your channel.. So many things for me to learn from your build... 🙏🏼🙏🏼🙏🏼
What company twist nuts did you use to mount the front of your Cliffhanger body???
I bought it from Amain - alnk.to/a3YChWQ
Thx Brah!👍
You are welcome!
Hello Sir, do you use stock grey Element springs?
Yes, I am using stock springs.
Bad ass
Thank you. It works well.