From what I can see, this guy is amazing. Almost everything in his wood shop, be built himself. Very impressive. To say the least. Craftsman like this almost dont exist anylonger.
Dude, there are hundreds of channels that do this same stuff with equipment they built out of wood. You can multiply that with people who don't have channels that do this. Probably hundreds of thousands of people are like this.
I was planning to buy a sharpening jig, then I remember the scissors had to be sharpen too. Then here comes you video, a nice jig for knife and it works for scissors too. A simple and very useful design. Now I'll DIY instead of buying one. Thank you for your effort. Just subscribed.
I made this in an afternoon. I used poly carb plastic scrap in place of the steel knife alignment and scissor clamp. Getting the stainless sharpening rod down to exactly 3/8” took the most time. Try to find a rod that is the exact diameter or a tiny bit smaller. I also made a second rod about 6 inches longer which works better for me. A stop nut on the back of the rod is also helpful. Bottom line is that the design works great and is made for next to nothing cost wise. I then bought stones from Gritomatic for another $80. You will also need a digital angle finder.
I really like your method of holding the knife. Clamps will never get in the way like this, and the whole clamp assembly will never have any play or movement.
That second to last cut with the rolled paper, wow. That is scary sharp! Fantastic work sir! Just, wow. I've seen $1500 sharpening systems not get close to that level of sharp. That has to be like 25 or 40 on the sharpness index. I can't express how impressed I am. Really well done.
It's the fixed angle combined with a fixed location for the blade that allows perfect consistency on the sharpening. It's not so much the concept as the design and work he did to make it that's so impressive.
@@МаксимПустовалов-ь1б С хренали ты решил что у меня нет нихрена, ты меня знаешь что б такое заявлять?, а так наверное у каждого мужика в квартире стоит цыркулярка , сверлильный станок и т.п. умник...
I made the device that holds your angle grinder and all I have to say it's been the most used tool used for cutting. Thanks for the ideas and videos you provide for everyone.
I saw that when I watched this video and I have an old angle Grinder that I don't' use that much anymore. I'm going to make one too. I don't have it yet and I already know it's going to be useful.
Пока дошёл до изготовления деревянных тисков. Думаю, через годик другой, все-таки сделаю точилку....А если серьёзно- спасибо за труд и чертежи. Обязательно повторю!
A drop of 3 and 1 or any oil on metal as your drilling into it works wonders. You drill faster and keeps heat down so bits last longer. Someone tipped me this years ago so I'm paying it forward.
The diamond plates, the grinding stone and the leather plates all have different thicknesses. So I assume the angle while sharpening hast o be adjusted depending on the tool you use. Do you also do this?
Ah, ok. I also thought about the option to bring them all on the same level. But it seems also to be easy to adjust the angle by the threaded stud as seen on TSPROF video. Thanks a lot for your answer.
Tell me in what world is a home woodworking shop a manufacturing facility? 😂😂 stop crying about it and just do the work with simple tools it’ll just take more time.
@@renejosueiriaschavarria897 I just thought the same in the first cut he does on the saw, the main commentary must be watching the video on braille mode or so
Very impressive and thanks in advance for the plans, just a question and hopefully if not you someone can answer what are the actual things to sharpen the knives called?
Лайк за ваш вариант универсальной точилки! Для кухонного ножа у вас угол выдерживается в пределах 25 - 30 градусов. Но, по моему мнению, лучшей заточкой кухонных ножей была бы радиусная заточка поверхности лезвия, которая в разы повышала бы стойкость остроты лезвия ножа. Ведь тонкая режущая кромка при "малой" твердости материала ножа заворачивается, при "большой" твердости выкрашивается. Радиусную заточку поверхности в зоне режущей кромки можно получить с помощью рычагов на точилке. Я уверен, вы сможете сделать и многим ваша конструкция сможет пригодиться. Здоровья вам и удачи!
Easy to make a homemade copy of an in-use design. Quite another thing to start with a blank sheet of paper. Do you find the Sawing method works better than Out vs In? I did enjoy the video.
Hi. What is the advantage of tilting the support of the knife as compared as to just positioning the knife completely horizontaly and giving the total angle to the rod?
С помощью телефона - скачайте любое приложение с угломером. Кладу на верхнее основание, обнуляюсь, переставьляю на деревянные зажимы - показывает половину угла.
In my case the the rod end bearing has to be drilled to an diameter a bit bigger than 8mm since the steel shaft of my old printer has a diameter of also 8mm and I wasn`t able to mount the shaft in the bearing. And for sharpenning it should glide really smoothly. Think it`s easier to open the bore instead of grinding the shaft...;-) Did you have the same problem?
No, I used a roller from an old inkjet printer - it fits perfectly. The printer can be bought very cheaply on bulletin boards, cheaper than the shaft alone. I haven't tried it, but I think it's really impossible to grind the shaft - it's hardened, you'll only ruin it without special equipment.
The grinding worked perfect. At the end it was easier than bringing the bore of the bearing to 8.01 or so. I just clamped the shaft into the drilling maschine and worked the diamter smootly down with a 800 grid sand paper at the end. Now it slides smoothly through the bearing. The surface is not that smooth than before, but it is ok. Thank you very much again for your videos. Well done.
Could you provide a link to those sharpening stones? I've found some on Aliexpress, but not going very high grit, and definitely not a leather one for final polishing.
@@ВладимирГорев-э5й из покупного там не только токарный по дереву)) +сверлильный, дрели, болгарки… точилка конечно интересная, впервые вижу крепление на магнитах, но затрачено ого-го, у наших «мастеров» видел дешевле и проще, да и сделаны реально «на коленке»😅
@@ВячеславАрефьев-ь9д Сверлильный тоже самоделка, а дрели болгарки, ножовки, напильники и прочий инструмент как то сложно считать не легко доступным. Точилка и в правду несколько замудрёная))
Are all your tools hand made for the most part? Table saw,planer I can see the thing that holds the angle grinder is are the rest similar? The look to he for the most part
There is no doubt you can get an edge on any blade! I don't think I could build this cause I don't happen to have a broke printer, I guess I will have to stay with bench grinder. Thanks tho, you did an amazing job!
Кстати о напылении - когда-то имел возможность покрыть электроискровым методом карбидом вольфрама по одной режущей кромке на нескольких ножах.Они давно потеряли товарный вид, используются в подсобных работах, но никогда не точились! За счёт разной твердости кромок затачиваются при использовании.
Простая, добротная конструкция без излишеств. Особенно понравились упоры обуха для симметричной заточки лезвия с обеих сторон. Скажите, для чего нужна стальная пластинка спереди (13:05)?
Amazing construction, congratulations. One thing is not clear, sorry if this is a stupid question: what is the purpose of the vertical plate at the front?
I like the jig you built also very much and I had the same question. Do you use diamond plates or sharpenning stones? And to which grain size do you sharpen before you use the leather. What paste do you use on the leather? Thanks in advance for your answer. By the way I also love the style you do your videos. Great. Thanks a lot for inspiring.
А я думал, чего мне дома нехватает... Оказывается токарника, гриндера, циркулярки с торцевой, чтоб не тратить 25 баксов на китайскую радиусную заточную систему, а слепить ее самому 🤣
Лайк то я поставил но вопросы остались, почему при наличии распиловочного станка фанеру под углом надо пилить ручной пилой? Когда делал пропилы ножовкой по металлу, я подумал нет УШМ как в следующим кадре работает болгаркой, при наличии УШМ скосы на металле делаются на гриндире. Замысловатый весьма подход к контенту.
Your shop is fantastic! All the homemade jigs, clamps, fences, etc...
The sharpening jig is awesome!
Жю
Юююю
,,..,.,.........,.....,............,.😊😊😅😅😅😊😊😊😊😊..ю...........................................................................................................................................................................................................
Жю
Юююю
,,..,.,.........,.....,............,.😊😊😅😅😅😊😊😊😊😊..ю...........................................................................................................................................................................................................
Просто супер. Автор молодец. Спасибо за труд. Спасибо за чертежи.Дай Вам Бог здоровья и счастья в жизни добрый человек
From what I can see, this guy is amazing. Almost everything in his wood shop, be built himself. Very impressive. To say the least. Craftsman like this almost dont exist anylonger.
Dude, there are hundreds of channels that do this same stuff with equipment they built out of wood. You can multiply that with people who don't have channels that do this. Probably hundreds of thousands of people are like this.
I was planning to buy a sharpening jig, then I remember the scissors had to be sharpen too.
Then here comes you video, a nice jig for knife and it works for scissors too.
A simple and very useful design. Now I'll DIY instead of buying one.
Thank you for your effort. Just subscribed.
how did it go? did you make one?
U gave a new meaning to home made as i know some small factories that have less equipment ,resources,and skill power than u do. Nice job
Not to mention that all of his tools appear to be shop made!
Amazing ! The possibility of accurate knive position is the best of all. Incredible workshop setup too !! Congrat from France !!
Осталось дело за малым, сделать кучу вспомогательных станков и после сделать приблуду для заточки ножей. Элементарно, Ватсон.
И еще принтер купить и разобрать!))))
За станки отдельное уважение ✊
I'M W/ U ON THAT 1 MY FRIEND 👍🏿 BUT THE MACHINE= THE MAN HIMSELF 😀 4 MAKING/BUILDING ALOT OF HIS TOOL'S N HIS SHOP 👍🏿👍🏿👍🏿👍🏿
The best DIY sharpening jig I've seen on RUclips, there are many similar builds but this one has a sturdier precision build .
Key word "I've seen" and you seen not so much.
Pretty relaxing to watch your videos... Love your self made tools! Great content
I made this in an afternoon. I used poly carb plastic scrap in place of the steel knife alignment and scissor clamp. Getting the stainless sharpening rod down to exactly 3/8” took the most time. Try to find a rod that is the exact diameter or a tiny bit smaller. I also made a second rod about 6 inches longer which works better for me. A stop nut on the back of the rod is also helpful. Bottom line is that the design works great and is made for next to nothing cost wise. I then bought stones from Gritomatic for another $80. You will also need a digital angle finder.
I really like your method of holding the knife. Clamps will never get in the way like this, and the whole clamp assembly will never have any play or movement.
Wow that seems to work really well. A friend spent a fortune getting a hunting knife sharpener but this looks equally good
That second to last cut with the rolled paper, wow. That is scary sharp! Fantastic work sir!
Just, wow. I've seen $1500 sharpening systems not get close to that level of sharp.
That has to be like 25 or 40 on the sharpness index. I can't express how impressed I am. Really well done.
It's the fixed angle combined with a fixed location for the blade that allows perfect consistency on the sharpening.
It's not so much the concept as the design and work he did to make it that's so impressive.
Конечно своими руками так сможет каждый, ведь у всех есть эта артилерия профессиональных инструментов......
Ты хоть заметил,что вся артиллерия инструмента так же самодельная? Ктож виноват что у тебя нет нихрена?
@@МаксимПустовалов-ь1б С хренали ты решил что у меня нет нихрена, ты меня знаешь что б такое заявлять?, а так наверное у каждого мужика в квартире стоит цыркулярка , сверлильный станок и т.п. умник...
@@МаксимПустовалов-ь1б Ага, и токарный станок тоже самодельный.
@@МаксимПустовалов-ь1б
И лишнее помещение для циркулярки ,шлифовалки,сверлилки и прочего инструмента...😂😂😂
Кто-то берет и делает, а кто-то сидит и ноет инструмееента профессионального нет))))
Красивая получилась и точит хорошо.
I made the device that holds your angle grinder and all I have to say it's been the most used tool used for cutting. Thanks for the ideas and videos you provide for everyone.
I saw that when I watched this video and I have an old angle Grinder that I don't' use that much anymore. I'm going to make one too. I don't have it yet and I already know it's going to be useful.
Papp
Пока дошёл до изготовления деревянных тисков. Думаю, через годик другой, все-таки сделаю точилку....А если серьёзно- спасибо за труд и чертежи. Обязательно повторю!
Spectacular work, I am assuming that if the knife holder is at 15 degrees, the bar that holds the whetstone is parallel to the table?
Обожаю когда пишут своими руками🧐👍только потом нужно ещё 3 станка,фрезер и ещё опыт 20лет👍
7 лет тому сделал с поворотным механизмом. Понадобилась для ее изготовления ножовки по металлу и дереву, дрель и две руки. Работает не хуже заводских.
Не нужно. Такое говно делается в гараже отвёрткой, дрелью и лобзиком.
У вас золотые руки и конструктивное мышление
A drop of 3 and 1 or any oil on metal as your drilling into it works wonders. You drill faster and keeps heat down so bits last longer.
Someone tipped me this years ago so I'm paying it forward.
Dude this is awesome. Your workshop is brilliant. I'd love one of those
Well done. How are you judging the edge angle?
That turned out nice.I should'nt have been such a good off in shop class.Learned more aboutsmoke
Nice. Real Nice. What grit sandpapers do you use??
Just a tip. Only stroke your stone downward then lift and stroke downward again. Very impressive jig!
Worked perfect the way he did 😊
@ pulling up against the knife can chip it if the stone grabs the edge..
On my to do list. What is the plywood material you used? Available in US?
Brilliant jig, just one thing, I dont understand how those plates hold the knife down?
That looks a very handy jig for making sharp knives. I need one!
It's not about just putting a keen edge on the blade but putting the correct edge for what's being cut and an edge that will last more than 3 cuts.
The diamond plates, the grinding stone and the leather plates all have different thicknesses. So I assume the angle while sharpening hast o be adjusted depending on the tool you use. Do you also do this?
I made it easier - I finalized everything to one thickness. At the same time, the sharpener allows you to adjust the angle due to the threaded stud
Ah, ok. I also thought about the option to bring them all on the same level. But it seems also to be easy to adjust the angle by the threaded stud as seen on TSPROF video. Thanks a lot for your answer.
When you have a medium sized manufacturing facility at home I dont think you should use the term home made.
I see your point, but everything he did is doable with the most basic tools right? Hand drill, anglegrinder and a handsaw will get you there.
Tell me in what world is a home woodworking shop a manufacturing facility? 😂😂 stop crying about it and just do the work with simple tools it’ll just take more time.
If you see all the video, you will notice that all his machines has components made by him, you can watch other videos to do tools like him
@@renejosueiriaschavarria897 I just thought the same in the first cut he does on the saw, the main commentary must be watching the video on braille mode or so
He has far less in the video that I have in my shed, and I'm just an old jackass.
Brother, your jig and tooling game is impeccable! You've earned a new sub.
Я конечно,с уважением.но использовать такой инструмент,жара.автору респект.
Very impressive and thanks in advance for the plans, just a question and hopefully if not you someone can answer what are the actual things to sharpen the knives called?
Sharpening stones. Those look like Venev brand ones.
Лайк за ваш вариант универсальной точилки! Для кухонного ножа у вас угол выдерживается в пределах 25 - 30 градусов. Но, по моему мнению, лучшей заточкой кухонных ножей была бы радиусная заточка поверхности лезвия, которая в разы повышала бы стойкость остроты лезвия ножа. Ведь тонкая режущая кромка при "малой" твердости материала ножа заворачивается, при "большой" твердости выкрашивается. Радиусную заточку поверхности в зоне режущей кромки можно получить с помощью рычагов на точилке. Я уверен, вы сможете сделать и многим ваша конструкция сможет пригодиться. Здоровья вам и удачи!
Линзовидную заточку на тонком (сведении)ноже делать по моему мнению без толку!
@@АндрейГ-ь6ж Если угол 25 - 30 градусов, то линза будет работать, если меньше угол, то не стоит делать.
@@opytkulikova дело не в угле заточки а в сведении, зачем делать линзу при сведении например 0.2? там и разницу не почувствуешь
@@АндрейГ-ь6ж Да, вы правы!
Задолбали вы своими градусами! Самому не смешно?
Профи из себя корчите. Исчезни!
Красивый результат! 🎉🎉🎉🎉🎉
Where did you get the small ball socket that you feed the rod through
Так сложно, черезмерно замудрено. Терпения не хватит досмотреть до конца, а сделать такое чудо тем более.
What did you use for the magnetic-base..?
A plastic magnet? Seems neodymium strong ... or is the strength just a product of its size?
It's a Neodymium magnet Ø20×3 with hole
More info here - FREE plans mazaydiy.com/diy-knife-sharpening-jig-2-0/
Easy to make a homemade copy of an in-use design. Quite another thing to start with a blank sheet of paper. Do you find the Sawing method works better than Out vs In? I did enjoy the video.
Шикарно, умница!!!
Love ❤❤❤❤❤ your content so much. I wish dearly I had cross your clips way sooner. Your clips are pure GOLD. God bless you and God bless Israel. ❤❤❤❤❤
Quick tip: band saws are great for cutting light gauge metal like that, and you almost certainly have one already.
Hi. What is the advantage of tilting the support of the knife as compared as to just positioning the knife completely horizontaly and giving the total angle to the rod?
Your adjustment rod does not have to be as tall.
Beautiful work. What is the piece that came in the little green box called?
They are called Heim joints or spherical rod ends.
Отлично у вас получилось,на заказ делаете?
Outstanding video and your collection of shop made tools and jigs is excellent!
Большое спасибо. А ссылочку можно на линейный подшибник ?
Is there any particular 📐 angle that the wedge is at ? No one says what degree to cut or set the knife rest
Подскажите, какого размера магниты вы использовали и какое у них сцепление?
Приветствую! Скажите пожалуйста, как Вы вычисляете угол заточки?
С помощью телефона - скачайте любое приложение с угломером. Кладу на верхнее основание, обнуляюсь, переставьляю на деревянные зажимы - показывает половину угла.
@@MazayDIY Благодарю Вас! Будьте здоровы!
Подскажите, какие магниты и где приобрести? Я имею ввиду силу самих магнитов.
0:01 - 0:04
Those cuts make my traditional stone sharpening look like the work of a novice...
What do you call that part that lets the rod move freely.
Мастерская ,,РАЗСКАЗАЛА ВСЁ о тТебе ,, ☝😕😁👍👏👍 !!! ЗАЧЁТНЫЙ ЛАЙКОС 👍✊🙋 !!!
Hey Mazay. Great video. thanks for sharing.🍁👍👍
Hi is possible buy in of this sharpener by you ? What’s the grades of stones that you use ?
Nicely done! @3:56 is why I’ll never take up metal work as a hobby. The sound of a file going over metal. It disturbs me greatly. Never knew why.
Просто oxyeннo... смотрел с удовольствием..👍
In my case the the rod end bearing has to be drilled to an diameter a bit bigger than 8mm since the steel shaft of my old printer has a diameter of also 8mm and I wasn`t able to mount the shaft in the bearing. And for sharpenning it should glide really smoothly. Think it`s easier to open the bore instead of grinding the shaft...;-) Did you have the same problem?
No, I used a roller from an old inkjet printer - it fits perfectly. The printer can be bought very cheaply on bulletin boards, cheaper than the shaft alone. I haven't tried it, but I think it's really impossible to grind the shaft - it's hardened, you'll only ruin it without special equipment.
The grinding worked perfect. At the end it was easier than bringing the bore of the bearing to 8.01 or so. I just clamped the shaft into the drilling maschine and worked the diamter smootly down with a 800 grid sand paper at the end. Now it slides smoothly through the bearing. The surface is not that smooth than before, but it is ok.
Thank you very much again for your videos. Well done.
Could you provide a link to those sharpening stones?
I've found some on Aliexpress, but not going very high grit, and definitely not a leather one for final polishing.
Could you please share the dimensions of the grinding machine?
With such a set of tools, machines and equipment, is it called your own hands? Funny. This is a real factory.
Не подскажете какой длины у вас вал от принтера ?
Отличный станочек, 🛠️⚙️🔩
Excellent job!
Merci beaucoup pour la vidéo et les plans
Точилка и плюс маленький цех ценой в тысячу точилок.
если внимательно посмотреть, то почти весь цех он сделал сам. из покупного там только токарный по дереву.
@@ВладимирГорев-э5й из покупного там не только токарный по дереву)) +сверлильный, дрели, болгарки… точилка конечно интересная, впервые вижу крепление на магнитах, но затрачено ого-го, у наших «мастеров» видел дешевле и проще, да и сделаны реально «на коленке»😅
@@ВячеславАрефьев-ь9д Сверлильный тоже самоделка, а дрели болгарки, ножовки, напильники и прочий инструмент как то сложно считать не легко доступным.
Точилка и в правду несколько замудрёная))
Kinda think I’d be happy with half his talent
How do you set the blade angle? Is it the height of the guide on the threaded rod?
That's right - the bottom nut allows you to accurately set the sharpening angle
Здравствуйте, подскажите пожалуйста как называется деталь что на шпилька надета,по которой ось с камнем скользит ,и где её купить ?
Are all your tools hand made for the most part? Table saw,planer I can see the thing that holds the angle grinder is are the rest similar? The look to he for the most part
Yes, I did all this myself. Watch my other videos on the channel - most of the machine tools have drawings so you can repeat
There is no doubt you can get an edge on any blade! I don't think I could build this cause I don't happen to have a broke printer, I guess I will have to stay with bench grinder. Thanks tho, you did an amazing job!
You can easily but stainless steel rods that size for a few dollars/euros on Amazon
Посмотрел, оценил наличие инструмента, достал надфиля с напылением и поправил все ножи до уровня бритвы.
Вся эта заточка ножей из нержавейки потеря сил и времени, до первого огурца... достаточно иметь качественный мусат.
Кстати о напылении - когда-то имел возможность покрыть электроискровым методом карбидом вольфрама по одной режущей кромке на нескольких ножах.Они давно потеряли товарный вид, используются в подсобных работах, но никогда не точились! За счёт разной твердости кромок затачиваются при использовании.
Да можно хоть о дно блюдца точить! 😆 Вы понимете вообще смысл таких точилок?
Простая, добротная конструкция без излишеств. Особенно понравились упоры обуха для симметричной заточки лезвия с обеих сторон. Скажите, для чего нужна стальная пластинка спереди (13:05)?
Спасибо! Пластина предназначена для закрепления ножниц
@@MazayDIY Понятно, благодарю за ответ.
this is a nice jig 👍
hadé pisan euuuy... urang nyieun ah...
why the vertical steel axis is not in the middle but at the edge ?
the length of the swiveling thingy puts the horizontal rod in the center of the jig.
Как понять какой угол заточки ножа если он у вас изначально закреплён под наклоном?
Да по%%й какой! Примерно выбрал, на кухне попробовал - если удобно, таким и остальное точишь.
магниты какие нужны,почему то у меня не держат нож?
Неодимовые бери - самые мощные.
Amazing construction, congratulations. One thing is not clear, sorry if this is a stupid question: what is the purpose of the vertical plate at the front?
Sharpening scissors. He show it here 14:25
@@sulumbekdolkh4705Thanks. I found out in the meantime.
Outstanding 👏
Which sharpening stones do you use, do you have a link for them?
Thanks!
I like the jig you built also very much and I had the same question. Do you use diamond plates or sharpenning stones? And to which grain size do you sharpen before you use the leather. What paste do you use on the leather? Thanks in advance for your answer. By the way I also love the style you do your videos. Great. Thanks a lot for inspiring.
Здравствуйте. Замечательное приспособление аж хочется самому зделать . Немогли бы вы поделится чиртижом если он есть ?
Hi, I'm from Colombia, do you have it for sale? I'm interested in a knife sharpener. Thank you.
От чего этот шарнир?
Продаётся на али, на озоне тоже есть. Искать "шарнир точилка".
А я думал, чего мне дома нехватает... Оказывается токарника, гриндера, циркулярки с торцевой, чтоб не тратить 25 баксов на китайскую радиусную заточную систему, а слепить ее самому 🤣
"гриндер" 🤣🤣🤣 "Хи-фи, Клюева!" - вот вы из таких же деревенщин. Grinder - читается как ГРАЙНДЕР.
Здравствуйте, зачем с одной стороны резьба сточена?
Have watched several timed and do not see how the blade is clamped to the jig What am I missing?
at the top of the jig are round neodymium magnets. Perhaps the plans will help you figure it out, it's free, a link to them is in the description
@@MazayDIY Thank you.
Лайк то я поставил но вопросы остались, почему при наличии распиловочного станка фанеру под углом надо пилить ручной пилой? Когда делал пропилы ножовкой по металлу, я подумал нет УШМ как в следующим кадре работает болгаркой, при наличии УШМ скосы на металле делаются на гриндире. Замысловатый весьма подход к контенту.
Почему была выбрана точилка, а не телескоп?
Готовится выживать.
Как называется эта штука с шарнирной втулкой в которой сама ось с камнем ходит?
Это подшипник скольжения сферический TSF 8, в описании видео точилки есть ссылка чертежи с размерами и перечнем комплектующих
great Video!
Чудесно ! Ножницы газету мокрую режут ? Спасибо.
Тебе зачем мокрую? Плачешь, когда читаешь о себе заметки? 🤣
what angle is set
When you say HOMEMADE, sounds like it´s in my home, man i have no the kiand of equipments like a Workshop
Своими руками)))) на заводе сделал!
Pl provide various dimensions/measurements. Thanks
Pradeep Shukla, check video description for free plans with dimensions
I like one best in know hands ., but i am used to stones double sided sharpener