Hello, you set the tester to 36V and test a 32V LED plate, but for the other LEDs (12V - 1.8V) you change the setting or once set to 36V this tester no longer needs to be adjusted and you can test any LED with a lower value without the risk of it burning out.?
I got a question Were you adjusting the voltage every time when testing different lights ?? Because this buck converter needs to be adjusted manually and I think this adjustment doesn't happen automatically !!
Resistor drop voltage amps, so don't worry, this method is used in LED backlight where led strip is 32 or 42 or 60v but input voltage from circuit are 90-120v with some resistors in between these resistors drop volts
это повышающий и он не может выдать 2 вольта, если только аккумулятор не разряжен полностью, есть ещё понижающе-повышающий преобразователь тоже на микросхеме xl6009, но на нём 2 дросселя
@@vitos3076а я не знаю почему я два вольта написал, там просто в ответе есть, что он понижающий 🤷🏼 а так всё правильно 2 вольта и другие напряжения, это напряжение падения на светодиодах
Very very helpful....Thank you sooooo much
I‘d add a switch because these converters often draw some current even if there‘s nothing at the output.
Yes
Wow.. Great idea ❤❤ very impressive
Thankx
@@TARIQLAB most welcome Bro❤❤
Vibhai moj kar de
Bohat zabardast cheez bnai he bhai ya circet kahan sy mily ga is ka name kya he agr ya apsy mangwana ho to kya triqa hy
Main Pakistan mahi hon abhi, electronics parts ki shop se mily ga, name, dc-dc booster 4v to 37v
Wow nice project, I tried and it works osm, thanks sir you saved me Rs700.🙏👍👌
Great 👍
NICE
Mengapa tegangan pada step up di set maximum 36 Volt ? .. amankah klo di setting lebih dari 36 Volt ?
Terima kasih atas videonya ..
modul kapasitas maksimum 40v, 36v adalah kisaran aman
Is per meter laga detay kay kitnay v led chip lay rhi ha to bara mast project ban jana tha bro
Han
I can use MT3608 ?
Hi..where to buy this circuit part DC-DC boost converter XL6009E1 2V to 36V..🙏
Electronics shop or online
Sirve un LM2556 ?
Hello, you set the tester to 36V and test a 32V LED plate, but for the other LEDs (12V - 1.8V) you change the setting or once set to 36V this tester no longer needs to be adjusted and you can test any LED with a lower value without the risk of it burning out.?
No need to adjust because resistor reduce current
@TARIQLAB OK, thank you for your reply. I don't know anything about electronics, so I'd rather ask questions than remain in the dark. ;o)
No problem 👍
I got a question
Were you adjusting the voltage every time when testing different lights ??
Because this buck converter needs to be adjusted manually and I think this adjustment doesn't happen automatically !!
Resistor drop voltage amps, so don't worry, this method is used in LED backlight where led strip is 32 or 42 or 60v but input voltage from circuit are 90-120v with some resistors in between these resistors drop volts
@@TARIQLAB thanks it helped !!
Welcome
How to clean solder iron tip
Steel wool
Onde eu encontro pra comprar
Online
Essa praca é do quê
amplificador de tensão
How to orde just like this thru online
Online AliExpress, Banggood,
I m not 330 ohm 1 watt resistors can i use 330 ohm 2 watt resistor?
Ok better set voltage below 30v
Why, because most of them all do that?@@TARIQLAB
Здравствуйте! Можете ссылку на плату скинуть ?
понижающий усилитель XL6009E1
@@TARIQLAB спасибо большое
это повышающий и он не может выдать 2 вольта, если только аккумулятор не разряжен полностью, есть ещё понижающе-повышающий преобразователь тоже на микросхеме xl6009, но на нём 2 дросселя
@@user-od7wv7bz3z Модуль и не выдаёт 2v, он выдаёт 36v, а резистором ограничен ток, так что и при 36v 2-х вольтовый светодиод не сгорит.
@@vitos3076а я не знаю почему я два вольта написал, там просто в ответе есть, что он понижающий 🤷🏼 а так всё правильно 2 вольта и другие напряжения, это напряжение падения на светодиодах
where we see voltage it every test?.
Put a small dc voltmeter
@@TARIQLAB Thanks you
Is me sarkit bot kes lgat heya bhai
Bahot easy hai
Why don't you all throw out the beans, come 30? Why don't you increase us to 46 to the maximum?❤❤
Iska saman kaha milega
Electronics parts ki shop se
its automatic
Yes
Как 2V получилось ?
сделай эту схему и проверь
Это падение на светодиоде
I can use MT3608 ?
Yes