BMW E36M43 Installing CYLINDER HEAD part 1 I Cylinder Head part 13
HTML-код
- Опубликовано: 6 сен 2024
- Part 1: • BMW E36 M43 cylinder h...
Part 2: • BMW E36M43 Exhaust Man...
Part 3: • BMW E36M43 remove the ...
Part 4: • BMW E36M43 Camshaft-Ro...
Part 5: • BMW E36M43 keepers, re...
Part 6: • BMW E36M43 Cylinder He...
Cara kerja teratur dan juga bersih. Terbaik boss
Good work❤
8:11 do I have to move piston to make clearance if I’m reusing old pistons and just replacing head? I’d rather not take it off tdc if I don’t have to
It depend on you.
Me, for safety i chose to move the piston
@@motoren_works I should have waited until the end, so you take the Allen out, move piston down a bit so none are right at top, torque down then reset tdc and put Allen back in to make sure it’s on tdc as well as double checking the marks are lined up? I guess can’t really make a mistake if the timing chain is zip tied hey, also do you have a link to the start of this job, I need to know how to get the intake manifold off and what I have to do to get to taking the rocker cover off, thank you. Your videos are great help
@@mattydalton7024 upper intake ruclips.net/video/WAuMxrnbt8A/видео.htmlsi=BT28D5Bb_2JeO5xc
@@mattydalton7024 lower intake ruclips.net/video/TeK1NF7H-dw/видео.htmlsi=AdfT6Nm_7wqcJDi9
@@mattydalton7024 you can check my others video in playlist: E36BMW
15:05 What did you put on the head bolts?
Engine oil
@@motoren_works Thanks mate, just wanted to make sure as i am going to be doing the same to my m43b19 soon
@@motoren_works Another question, at 6:09 what is the purpose of putting the allen key there? Sorry for asking so many questions XD
@@RasterYTthe purpose is to lock the flywheel. Flywheel has a hole, If the flywheel hole is parallel to the engine block hole, this means the TDC position is correct. It can check from the dumper gear in the front of engine (6:39)
@@motoren_works Thank you, i really appreciate your help. i don't think i would attempt to replace my cylinder head myself if it wasn't for your videos, You've defiantly earned my subscription 😁
Itu lem apa.om yg d pke di baut2 head..
Bukan lem tp oli mesin om
Buka jasa untuk bersihin mesin sm ganti packing head om? Mesin nya sm e36m43
Tidak om :)
Hello i have a m43b18 and i have an issue with poor accelerating, when i push the gas pedal fully it builds rpms slow without hiccups any idea what could be the problem?
I have friend with the issue like that. The problem source is bad camshaft sensor. I hope it's same with yours. Note: there are no issue at other parts
@@motoren_worksThanks, i uploaded 2 videos of the car working, i wouldn't think that the camshaft sensor could be the problem in my situation myb im wrong. And the gas pedal feels delayed or slow and when i roll the car reverse or in front sometimes the car goes to 0 rpm then wakes up barely when i press the clutch an then works normally. Thanks for the respond
@@VelocitySlidesafter i checked your videos, first please check your AFM flap movement, it must be smooth. If the movement smooth, and then check your TPS
@@motoren_works will do that thank you
@@motoren_works Hello so i checked my TPS i had my multimeter on 20kΩ it read bottom pin and top pin 3.9, the bottom and middle pin was 4.4 to 1.48 when fully pressed throttle, and i checked the AFM flap it went smoothly no problems at all. Is the tps good or need a replacement?
Om, berapa Nm moment baut cyl nya? Oiya itu top nya tdi di gigi 6, kog dipindah ke gigi 14 ya om?
30 Nm tp dia ada 3 stage untuk ngencengin baut cyl. head, lengkapnya ada di part 2 om ruclips.net/video/W8BY9dmhhEU/видео.htmlsi=tILgvrKcXriZuZgQ. Sy mindah posisi top turun sedikit tujuannya untuk safety, jaga2 agar klep yg sedikit terbuka tidak beradu dg piston ketika cyl. head dipasang
@@motoren_works 30nm + 90° putaran ya om. Aman om
@@adysupriyono83 betul om
@@motoren_worksэто обязательно делать?
@@user-rn3gb5qb9f sesuai dengan spesifikasi