BEFORE WATCHING! What do you reckon is waiting for us inside the S65 engine? Place your bets - original bearings? Copper or later updated ones? Been changed recently? About to fail?
Great video! It’s such a variation of how more or less worn the bearing are on different year builds and mileage driven. Would you attribute the excessive wear on lower mileage to be due to hard driving patterns and/or poor maintenance? • Btw, Ryan and Cat are so amazing to chat with at IND and I agree that Fall-Line parts upgrades vs stock will be the best way to go 👍🏽💯
Awesome video, it shows that these motors are capable of holding up if they receive good maintenance. Seems like the previous owner respected the car and followed the proper warm up cycle as well, which if not done could also result in failed bearings.
I wouldn’t call bearings worn down to copper as holding up...who knows what the history of the car is, but as was pointed out, if the car had been driven hard or tracked cylinder 8 could’ve gone fairly easily. But yes, it does show that the bearings can last...but bearings should still likely be changed every 50-60k miles. Probably much sooner if tracking the car regularly. What was more concerning to me is hearing that the car with only 30k miles had worse wear. Just goes to show that there is no rhyme or reason for how and why these bearings wear how they do and mileage on the car doesn’t count for much. The best you can do is try to buy a car with long term ownership and maintenance records which is pretty much the rule for any car. Then it’s still no guarantee and you better change the bearings ASAP.
@@ericm8368, these motors are notoriously know for failure due to worn bearings at a lot lower mileage. My comments were on the fact that this particular example "held up" a lot longer than most S65s. Bearing replacement on these motors are considered a maintenance item, crazy to think so I know, but unfortunately it is. 🤣
@Eric M - We believe that number of cold starts and how the car is driven whilst cold is the main contributing factor to the wear. The 30k car may have not been looked after, regularly driving hard from cold, lots of short journeys to not allow the car up to temp etc. Unfortunately it’s impossible to know how a used car has been treated in that regards. If it was directly linked to mileage it would be more simple but as this car shows it is not.
I thoroughly enjoyed watching this video. Very informative and soothing to watch at the same time. Job well done to Aston and the guys at Evolve. Can't wait for Imran to do the test drive.
These guys did my Rod bearings on my e93 M3 last week and they did a great job. I can honestly say I trust Evolve more than I trust the BMW main dealers. These guys don't only know their stuff but they are really friendly towards their customers. Evolve are the only company I would trust with my beloved M car. FACTS!
@@EvolveAutomotive When I was at your workshop last week, I had to leave my car with you overnight. I was about to arrange an Uber so I could get to the nearest train station in order to get home when one of your staff told me to put my phone away as he would drop me to the station!!! I'm not going to lie, I was taken aback as your fella did not have to do that. It's these little touches what will keep me and other customers returning. So not only do you get a professional and trustworthy job carried out on your car, you also get great customer service. Keep up the good work Evolve. 👍
Thank you gentleman for sharing, might be a small audience for content like this but extremely appreciated, thankfully there's still some engineers and technicians out there
I changed my 740 Schnitzer engine mounts a few months ago as I just like to change everything. My passenger side mount looked like yours, and exploded as it was removed! Changed the transmission mounts aswell. Used Febi Bilstein ones, fitted a treat.
Well worth the wait for this one, just goes to show that if the car is well maintained and not ragged the bearings can last. When I get an E92 im bringing it to you.
I have a 2013 m3 6mt and I am eagerly watching these videos. Mine has only 28,000 miles and I am the original owner. But I am fascinated by this car and can’t wait to see what you guys do with it!
Great idea for this build series. Well done to the owners of this car, it just shows mileage is just a number with proper maintenance 150k is better than 60k in some cases :)
I did mine at 90k miles with some fellow e90/2 m3 owners. I was a bit scared. The real work is the sub-frame. There was some copper showing on a few of the top bearings, but not much really. I am the original owner and now have 130k miles. I get an oil analysis at every change and the results have always been superb. It runs like new and I love it. I had to rebuild my diff and lsd recently (put in the 4:10 gearset) and all new bearings. That was much harder and less fun than doing the rod bearings.
Amazing first ever video I've watched from the channel and I must say that I won't stop watching vids from Evolve...however, the background tune sounds so much like 'The Game-soundtrack'.
Good that you guys maintained objectivity and demonstrated how a high mileage car that is maintained can have rod bearings that don't look bad. Motor mounts on any car with that kind of mileage will see that kind of wear.
Amazing vlog Imran, well done to the previous owner 👍 I was dreading this being the end of the project with the thumbnail, lol. Heard so much about the rod bearings on the E92. Finally able to see some content on it and see it in action, being done. Salute to Aston mans a ///Magician legend!
Ok ok, I’m a little more relaxed now, my e93 has 60.000 miles on the clock and I always worry about this bearings, even tho I always warm up the engine and never rev it more than 3000 until fully warmed, Still in plan to change them soon but hard to find good trusty shops nearby. And great videos guys, I like this project and I’ll follow it closely, curious what you guys will do with it. Cheers
Great project and vid. I love seeing these type of series and Aston is great at explaining what he is doing and making it simple to understand. Nearly at 100k subs too. I'm sure that goal will met very shortly. Keep up the great work.
Love how the oil coming from the rear plug was nice and amber while the oil from the front plug was black. Seeing how the rear bolt was not stock while the front was, there’s a possible chance that previous servicer, probably former owner, wasn’t aware of the front plug. My 2011 leaks right in front where oil pump is, another item I need to look at when I do my bearings.
Amazing series gents. Love it!!! I remember you mentioning on one of TR Hamza's videos that you were gonna do a high mileage project. I love being able to learn some mechanics like this!!
I changed mine preemptively at around 75.000 miles and they were, in comparison, in a much, much better shape. The copper wasn't even exposed. I never rev the car cold and this proves, in my mind, that most engines failures is most likely a direct result of abuse from clueless owners. As with any sport cars, if you don't treat them as such they will inevitable fail.
@@EvolveAutomotive I guess most owner don't save their car for the next owner. I have no intention of selling my M3 (manufactured october 2007) so I take care of it 😁
Right, a very mabusive owner... No, but for real, I think it comes down to a few things. Oil quality, how often changed. The thickness of the oil, and the cold starts of the engine. When the engine is cold, the oil pressure is high! and this means that it is very hard on everything until it is warmed it. I always baby my N55 engine when it is cold. Always do the oil very often. Let them warm up for a long time. The rod bearings sit on a very thin layer of oil, and they are not designed to touch the crank. If the oil level is too high, or too low, they will. There are very small holes in the journals, and if the oil is too Thich, it will not do its job.
Hey guys I really enjoy watching all the things that you do with all the cars. As I have a E90 M3 and have done the rod bearing as you guys have and wanting to purchase some of the products offered and programs but, I am having concerns of the main bearing and what I am learning about the S65 vs the S85 - what are some of your guys thoughts?
Damn man i’m at 98k miles can’t wait to get these done one less worry in my mind. I honestly rather worry abt the trans taking a sh** then the rod bearings breaking lmao
@@EvolveAutomotive Well good to know that was a worry of mine is there anything else I should worry about besides rod bearings and the dct? Like expensive stuff yk
Great video guys. I started a similar project about 2yrs ago. Bought an 09 on 123k on original bearings. Changed them straight away and looked reasonable, small amount of copper showing but nothing worrying. Interested to see where you go with this. Hopefully will show that a leggy e9x is nothing to be worried about.
The rod bearings on my e92 give up at 72k and only had the car a few weeks lucky for me I bought it from a dealer so got my money back but after saving up for a while it was disheartening after wanting one for so long
How do the Main bearings hold up ?...would like to know how often the mains fail...and if they still fail after having the oe rod bearings replaced with BE ones
At the end of the video, the car does a weird fart sound when he turns on the car. My M3 does the same thing sometimes when I first turn it on. Do you know what exactly is that sound and is it something to be worried about?
I’m at 95k on my e93 M3 and I plan on changing the bearings myself but every time I drive her I let her warm up for about 15 mins just changed the oil too and she runs great!
Can i ask, which oil would you advise on these old bmw, i drive an e46 325i 05 with 237000km. Usuallyi hear people saying we must not use castrol but you'll are using it. What can you recommend, Aston?
Just digging into this series and think I'm really gonna like it. As a sidenote it's absolutely ridiculous that a ccompany the size of the Milwaukee haven't stress tested their M12 platform with the likes of their impacts for drop testing and 1000's of insert/removals of the battery and wearing of the tabs. I've seen the cable tieing of the battery quite often... Thumbs up I prefer these projects as they feel a bit more realistic to the average viewer in the UK as opposed to brand new 50k + cars upgrading their performance.
great video ! I recently replaced my e92 m3 radiator,condensor and fan. When i started filling up my coolant noticed it leaked all the coolant from a hole thats on the drivers side of the radiator, i dont recall removing anything from there from the old radiator and by looking at your video at minute 5:50 right on top of the rusted line you can see that yours doesnt have anything connected to that hole either. Not talking about the blue drain plug. Can someone explain to me how i keep coolant from leaking from that hole.
Amateur Question : If the bearings are out of round, is the crankshaft not out of round also ? So will the new bearings not just start to wear excessively ?
Cranks are so bloody hard now I’d be surprised if the crank was worn considering the wear on the bearings. You normal get crank wear if the crank has worn completely through the bearing surface.
Think about the movement going on. Rod and journal comes down and deccelerates. Comes up and deccelerates. It is basically describing a very slightly oval arc. Ergo slightly oval bearings.
question.....Would a black stone analysis have showed any symptoms/precursors to cylinder 8's journey to fail? Like anything to suggest the extra wear?
So is that first thing to change on a high mileage performance car as you have mentioned rod bearings numerous times. Just wondering if there are other components to take into consideration prior to changing the bearings so basically must change, should change and nice to do or change.
@@EvolveAutomotive OK thanks. I'm watching the video again and learning so it's great to know the bearings are in order of priority given the cars age, mileage etc
Loving watching these Eps, plan to keep my 50k 2012 92 for as long as I can, so preventative mods and potential failure parts that you guys might make to future proof them I'm very keen to see what this development car is it is will bring us 9X owners! Keep it coming!
I've got an Alpina 335 M coupe bi turbo, do these suffer with this problem after Alpina have tuned the engine ? It's an E92 on an 08 plate with 73,000 miles.
Can I ask, why are the crank bearings called rod bearing??? I know theyre attached to the Conrod But I thought the rod bearings were the small end bearings at the piston end
@@EvolveAutomotive thank you for explaining I understand it now, it’s not what the crank runs on it’s what the rods run on,doh!! Don’t you check or do the main bearings as a matter of course after making that much effort
I've been thinking of buying one of these... Usually I'm not worried about doing the work myself. Done everything on my current bmw... but damn it.. I dont have a hoist
BEFORE WATCHING! What do you reckon is waiting for us inside the S65 engine?
Place your bets - original bearings? Copper or later updated ones? Been changed recently? About to fail?
Great video! It’s such a variation of how more or less worn the bearing are on different year builds and mileage driven. Would you attribute the excessive wear on lower mileage to be due to hard driving patterns and/or poor maintenance?
•
Btw, Ryan and Cat are so amazing to chat with at IND and I agree that Fall-Line parts upgrades vs stock will be the best way to go 👍🏽💯
Hi Guys, do you do engine oil flash during the procedure or just quicker oil change?
I have no idea what a rod bearing is but I guess I'm about to learn!
Wouldn’t know as it’s luck of the draw, seen 30k cars have more wear then 100k cars, no rhyme or reason
Hi Evolve Automotive ,upgraded rod bearings not available on your website anymore?
I can see OEM only…
Thanks.
No denying Astons skills as a technician.... knows his stuff 👍
Alot of knowledge and experience in that big ol head
He demonstrated the difference between a mechanic and a technician, didn’t he? Wow!
Well done the previous owner. You've given Evolve a decent platform to work on.
I found this quite therapeutic
I 2nd this
😂
I can just hear your British accent through your comment 🗿
Me too actually!
I find it useful as 2nd owner of 2011 with 56k miles.
Awesome video, it shows that these motors are capable of holding up if they receive good maintenance. Seems like the previous owner respected the car and followed the proper warm up cycle as well, which if not done could also result in failed bearings.
I wouldn’t call bearings worn down to copper as holding up...who knows what the history of the car is, but as was pointed out, if the car had been driven hard or tracked cylinder 8 could’ve gone fairly easily. But yes, it does show that the bearings can last...but bearings should still likely be changed every 50-60k miles. Probably much sooner if tracking the car regularly. What was more concerning to me is hearing that the car with only 30k miles had worse wear. Just goes to show that there is no rhyme or reason for how and why these bearings wear how they do and mileage on the car doesn’t count for much. The best you can do is try to buy a car with long term ownership and maintenance records which is pretty much the rule for any car. Then it’s still no guarantee and you better change the bearings ASAP.
@@ericm8368, these motors are notoriously know for failure due to worn bearings at a lot lower mileage. My comments were on the fact that this particular example "held up" a lot longer than most S65s. Bearing replacement on these motors are considered a maintenance item, crazy to think so I know, but unfortunately it is. 🤣
@@Rayzor1502 I got it😉
@Eric M - We believe that number of cold starts and how the car is driven whilst cold is the main contributing factor to the wear. The 30k car may have not been looked after, regularly driving hard from cold, lots of short journeys to not allow the car up to temp etc.
Unfortunately it’s impossible to know how a used car has been treated in that regards. If it was directly linked to mileage it would be more simple but as this car shows it is not.
Okokk
aston does a fantastic job of explaining things. amazing team you have put together! would love to own an e92 now
Really are a special car, will happily recommend them to anyone.
Anyone with a lift 😂
I thoroughly enjoyed watching this video.
Very informative and soothing to watch at the same time. Job well done to Aston and the guys at Evolve. Can't wait for Imran to do the test drive.
These guys did my Rod bearings on my e93 M3 last week and they did a great job. I can honestly say I trust Evolve more than I trust the BMW main dealers. These guys don't only know their stuff but they are really friendly towards their customers. Evolve are the only company I would trust with my beloved M car. FACTS!
Thanks for the kind words! We really do love these cars 🥰
@@EvolveAutomotive When I was at your workshop last week, I had to leave my car with you overnight. I was about to arrange an Uber so I could get to the nearest train station in order to get home when one of your staff told me to put my phone away as he would drop me to the station!!! I'm not going to lie, I was taken aback as your fella did not have to do that. It's these little touches what will keep me and other customers returning. So not only do you get a professional and trustworthy job carried out on your car, you also get great customer service. Keep up the good work Evolve. 👍
how much was the job if you don't mind me asking?
£1500 inc VAT
Thank you gentleman for sharing, might be a small audience for content like this but extremely appreciated, thankfully there's still some engineers and technicians out there
I changed my 740 Schnitzer engine mounts a few months ago as I just like to change everything. My passenger side mount looked like yours, and exploded as it was removed! Changed the transmission mounts aswell.
Used Febi Bilstein ones, fitted a treat.
Well worth the wait for this one, just goes to show that if the car is well maintained and not ragged the bearings can last. When I get an E92 im bringing it to you.
I have a 2013 m3 6mt and I am eagerly watching these videos. Mine has only 28,000 miles and I am the original owner. But I am fascinated by this car and can’t wait to see what you guys do with it!
Did you need to replace your rod bearings?
I’m really keen on following this series, bought an e92 M3 couple months back aswell, already has the evolve stage 2!
Nice! What does the evolve stage 2 mean? In terms of power and added parts? 😃
Great idea for this build series. Well done to the owners of this car, it just shows mileage is just a number with proper maintenance 150k is better than 60k in some cases :)
I did mine at 90k miles with some fellow e90/2 m3 owners. I was a bit scared. The real work is the sub-frame. There was some copper showing on a few of the top bearings, but not much really. I am the original owner and now have 130k miles. I get an oil analysis at every change and the results have always been superb. It runs like new and I love it. I had to rebuild my diff and lsd recently (put in the 4:10 gearset) and all new bearings. That was much harder and less fun than doing the rod bearings.
Amazing first ever video I've watched from the channel and I must say that I won't stop watching vids from Evolve...however, the background tune sounds so much like 'The Game-soundtrack'.
Watching an expert work is always a joy.
These are well engineered cars. Thankfully people are recognizing that. 😊
A video about their engine bearings failing is an example of good engineering to you? Interesting bar for "well engineered."
@@hamsterbrigade We appreciate your feedback.
Know that you are loved and accepted. (:
Tell us more now?
Just had this done the other day, fitted by Hash.
Keep up the fantastic work guys👌
Good that you guys maintained objectivity and demonstrated how a high mileage car that is maintained can have rod bearings that don't look bad. Motor mounts on any car with that kind of mileage will see that kind of wear.
Amazing vlog Imran, well done to the previous owner 👍 I was dreading this being the end of the project with the thumbnail, lol. Heard so much about the rod bearings on the E92. Finally able to see some content on it and see it in action, being done. Salute to Aston mans a ///Magician legend!
Ok ok, I’m a little more relaxed now, my e93 has 60.000 miles on the clock and I always worry about this bearings, even tho I always warm up the engine and never rev it more than 3000 until fully warmed, Still in plan to change them soon but hard to find good trusty shops nearby. And great videos guys, I like this project and I’ll follow it closely, curious what you guys will do with it. Cheers
I hope this dude gets paid well, he deserves it.
aston does a great job explaining it all, awesome video
Professionals at work!
Sounds like you guys have a proper car now.👍Well done! It’s definitely a sigh of relief to know all is well. Another S65 saved!🙌
So professional and well filmed video.. looking forward to more 👍🏻
Its like art watching these guys at work
terrific video i will keep. there is so much to remember but you have been excellent. KEEP UP THE GOOD WORK. THE BOTH OF YOU. regards.
I think Aston could change the bearings in his sleep now, as usual a great insight into the workings of these cars, love your vids.
Great project and vid. I love seeing these type of series and Aston is great at explaining what he is doing and making it simple to understand.
Nearly at 100k subs too. I'm sure that goal will met very shortly.
Keep up the great work.
Wow, I had no idea rod bearings could be replaced w/o pulling the motor. Great video
Love how the oil coming from the rear plug was nice and amber while the oil from the front plug was black. Seeing how the rear bolt was not stock while the front was, there’s a possible chance that previous servicer, probably former owner, wasn’t aware of the front plug.
My 2011 leaks right in front where oil pump is, another item I need to look at when I do my bearings.
Videos like this is why I subscribed I love E9X M3 content cheers 🤙🏼🙌🏼
Got my guess right. Pleased to see it looking well looked after. Good base to see what comes next now.
Proof that maintenance is a must. Another great video
Great vid guys. Renews my interest in "swapping out" My E36 M3 for a low mileage E90 M3. 🙏
Amazing series gents. Love it!!! I remember you mentioning on one of TR Hamza's videos that you were gonna do a high mileage project. I love being able to learn some mechanics like this!!
Good strategy keep it up. We like to see this type of content and quality editing 👏
Good job I'm local, so when I finally get one myself I know where to bring it. PureGT has been useful.
I changed mine preemptively at around 75.000 miles and they were, in comparison, in a much, much better shape. The copper wasn't even exposed. I never rev the car cold and this proves, in my mind, that most engines failures is most likely a direct result of abuse from clueless owners.
As with any sport cars, if you don't treat them as such they will inevitable fail.
If it had the pre 2010 bearings that were copper then you did well. We rarely see an early car without at least a little copper showing.
@@EvolveAutomotive I guess most owner don't save their car for the next owner. I have no intention of selling my M3 (manufactured october 2007) so I take care of it 😁
Right, a very mabusive owner... No, but for real, I think it comes down to a few things. Oil quality, how often changed. The thickness of the oil, and the cold starts of the engine. When the engine is cold, the oil pressure is high! and this means that it is very hard on everything until it is warmed it. I always baby my N55 engine when it is cold. Always do the oil very often. Let them warm up for a long time. The rod bearings sit on a very thin layer of oil, and they are not designed to touch the crank. If the oil level is too high, or too low, they will. There are very small holes in the journals, and if the oil is too Thich, it will not do its job.
Hey guys I really enjoy watching all the things that you do with all the cars. As I have a E90 M3 and have done the rod bearing as you guys have and wanting to purchase some of the products offered and programs but, I am having concerns of the main bearing and what I am learning about the S65 vs the S85 - what are some of your guys thoughts?
Great video & very informative you guys know your stuff 👌
Haven't heard the workshop sounds integrated with the audio before either! Was pretty cool 😎
this is so cool to watch post more on this car!!!
i want an e92 m3 so bad, i think im going to pull the trigger next year, fingers crossed 🤞 then I'm coming straight to Evolve!
Keep it coming lads, Quality & Aston is soo knowledgeable
18:27 Any idea what that noise is?? Mine has the exact same. Comes and goes on cold start.
Great work, loving the content. Keep up the good work 👏👍
The song in the background at 3:20. Cant remember the name, ive been hearing that EVERYWHERE i go lately.
Sounds like ‘I love you baby’ by Frank Sinatra, or a variant of it.
Damn man i’m at 98k miles can’t wait to get these done one less worry in my mind. I honestly rather worry abt the trans taking a sh** then the rod bearings breaking lmao
DCT failure is incredibly rare on these. Even at 152k we aren't worried about the DCT gearbox in this car.
@@EvolveAutomotive Well good to know that was a worry of mine is there anything else I should worry about besides rod bearings and the dct? Like expensive stuff yk
Throttle Actuators are the other main thing, we have a video on that here - ruclips.net/video/38XiDMIoH5I/видео.html
@@EvolveAutomotive Thanks man
Well done guys. Great video. And well done to your master tekker.
Great video guys.
I started a similar project about 2yrs ago. Bought an 09 on 123k on original bearings. Changed them straight away and looked reasonable, small amount of copper showing but nothing worrying.
Interested to see where you go with this. Hopefully will show that a leggy e9x is nothing to be worried about.
Great content guys. Very intuitive and keep it coming. Project N54 would be great 👍
Like the content on this, really useful if in the market for a m3. Looking forward to the build. 👍
Do you check bearing clearances when replacing stock bearings? I'm sure you guys have done enough of these to know if it's necessary.
The rod bearings on my e92 give up at 72k and only had the car a few weeks lucky for me I bought it from a dealer so got my money back but after saving up for a while it was disheartening after wanting one for so long
Did you buy extended warranty or was it covered by their standard warranty??
@@esthedik92most likely extended considering these cars r over a decade old
Good channel this, always learning. Wish you success in the future.
This video gives me the courage to buy an m3, change the road bearings and live a happy car enthusiast life afterwards :)
What about main bearing? Is there a risk of spinning one? Is there the same problem with small tollerance and spinning of of them?
Enjoyed a great and interesting lower end look.
Enjoyed that video, great work gents.
I can't get over how much rust there is under this car...it made me go out and check under my own 2010 E90 M3 Comp
Whoever gets mates rates from Ashton is lucky 🧺 great video as usual hope to see the next one soon
Great work 👌 fair play with that milage on it its pretty good 👍
is the crank/ or old bearings measured before putting in the new bearings etc,
This is a 2010 version? Monte Carlo edition with the newer Idrive controller? When did the revised (non copper) parts come out?
Built in Nov 2019, CIC iDrive. Updated bearings were March 2010 we believe with the LCI update.
Without measuring the crank how do you know if it’s ok to stick a new set of bearings in?
Great vid guys, really enjoyed & I haven’t even got an M3, I have got a BM tho.
Do you lubricate the new bearings before first startup or does the sump oil do this anyway? Thanks and great vid.
Yes each bearing is soaked in oil before being put in, as a protection before oil pressure builds after first start up.
Nice video and very nice music🙂
How do the Main bearings hold up ?...would like to know how often the mains fail...and if they still fail after having the oe rod bearings replaced with BE ones
At the end of the video, the car does a weird fart sound when he turns on the car. My M3 does the same thing sometimes when I first turn it on. Do you know what exactly is that sound and is it something to be worried about?
Superb video guys just brilliantly informative.
I’m at 156K on original bearings in my 2012 E92 M3. Now that I’m on stage 2 setup and tune, I’m eagerly watching this one 👀💪🏽💯
This man living life on the edge
Risk taker...
Playing with fire! lol
When you were born you drove your parents back from the hospital
I’m at 95k on my e93 M3 and I plan on changing the bearings myself but every time I drive her I let her warm up for about 15 mins just changed the oil too and she runs great!
YES!!!! More like this please 🙌🏻🙌🏻
Can i ask, which oil would you advise on these old bmw, i drive an e46 325i 05 with 237000km. Usuallyi hear people saying we must not use castrol but you'll are using it. What can you recommend, Aston?
Awesome vid! I own 2008 M3, bought back in 2011 with 43k miles and 10 years later ….149k miles :)
Just digging into this series and think I'm really gonna like it.
As a sidenote it's absolutely ridiculous that a ccompany the size of the Milwaukee haven't stress tested their M12 platform with the likes of their impacts for drop testing and 1000's of insert/removals of the battery and wearing of the tabs. I've seen the cable tieing of the battery quite often...
Thumbs up I prefer these projects as they feel a bit more realistic to the average viewer in the UK as opposed to brand new 50k + cars upgrading their performance.
Really interesting that.. I am currently looking at E63 M6s with S85 V10 and know that rod bearings are the main lookout for these cars.. 👍🏼
2:49 "Ok, that looks good. Let's put it back in."
What's the little slim torch he's using to show the oil leaks? Looks very bright for the size. And a nice handy profile
It’s actually a piece of video equipment
great video ! I recently replaced my e92 m3 radiator,condensor and fan. When i started filling up my coolant noticed it leaked all the coolant from a hole thats on the drivers side of the radiator, i dont recall removing anything from there from the old radiator and by looking at your video at minute 5:50 right on top of the rusted line you can see that yours doesnt have anything connected to that hole either. Not talking about the blue drain plug. Can someone explain to me how i keep coolant from leaking from that hole.
I have a manual 2004 e46 m3 and has 128k on the clock, owned the car many years now since 100k and this is always on my mind to do.
Amateur Question : If the bearings are out of round, is the crankshaft not out of round also ? So will the new bearings not just start to wear excessively ?
That’s the job of the bearing is to absorb the wear and impact of a moving metal on metal surface.
Cranks are so bloody hard now I’d be surprised if the crank was worn considering the wear on the bearings. You normal get crank wear if the crank has worn completely through the bearing surface.
Think about the movement going on. Rod and journal comes down and deccelerates. Comes up and deccelerates. It is basically describing a very slightly oval arc. Ergo slightly oval bearings.
question.....Would a black stone analysis have showed any symptoms/precursors to cylinder 8's journey to fail? Like anything to suggest the extra wear?
Your opinion on a 2013 BMW M3 convertible 86k bearings were changed ?
Whatever happened to doing the job properly & using plastigauge to measure the clearance?
Nice vid,no bollocks,just to the point!
So is that first thing to change on a high mileage performance car as you have mentioned rod bearings numerous times. Just wondering if there are other components to take into consideration prior to changing the bearings so basically must change, should change and nice to do or change.
We’re doing these videos in order of priority to us, so yes this is the first thing we would do.
@@EvolveAutomotive OK thanks. I'm watching the video again and learning so it's great to know the bearings are in order of priority given the cars age, mileage etc
Great video, can't wait for the next update 👍
Why do the bearings chew out after such low miles. I would be looking at addressing clearances and oil supply to the bearings to improve endurance.
your opinion of a 2013 M3 convertible will it hold up the bearings were changed and has 86k ?
Quality workmanship 💪🏻
Enjoyable video! Keep them coming.
Loving watching these Eps, plan to keep my 50k 2012 92 for as long as I can, so preventative mods and potential failure parts that you guys might make to future proof them I'm very keen to see what this development car is it is will bring us 9X owners! Keep it coming!
I'm glad you guys are keeping up the e9x m3 platform contents.
What bearing/bolts did you guys replace with?
We use all OEM parts
I've got an Alpina 335 M coupe bi turbo, do these suffer with this problem after Alpina have tuned the engine ? It's an E92 on an 08 plate with 73,000 miles.
Good Video… should i change the rod bearings on the M5 F10 now about 92.000 km its maybe 57-58k miles ? I cant find a video about m5 f10
Enjoyed this 👌🏽 This M3 couldn’t have gone to a better team! She’s going to be pampered 🌟
Can I ask, why are the crank bearings called rod bearing??? I know theyre attached to the Conrod
But I thought the rod bearings were the small end bearings at the piston end
You have main bearings which sit between the crank and the block, and Rod bearings that sit between the crank and the conrod.
@@EvolveAutomotive thank you for explaining I understand it now, it’s not what the crank runs on it’s what the rods run on,doh!! Don’t you check or do the main bearings as a matter of course after making that much effort
To do main bearings requires complete engine strip down and rebuild.
@@EvolveAutomotive huge job!!! Awesome work by the way and keep the video’s coming they’re great 👍
I've been thinking of buying one of these...
Usually I'm not worried about doing the work myself. Done everything on my current bmw... but damn it.. I dont have a hoist