did you change the diameter of the circle in sketch 4,because 63.5 seemed a little too big while in the video it looked smaller.could be imagining things tho.
Everything was fine except last moment big circle but no hole in middle so why there is a small extrude and hole in it could be without a hole as well?
hey! your videos are awesome!!! but, one question..... how can i choose the material that you use? why you piece shines?? what is the option to choose this material??? please! tellme!
the boundary boss/base in 4:30 doesn't work in the same way that he does, why? I've tryed to follow each instructions, but I suppose that the conflict concerns the green line of the profile.
seems a lot of critical steps are skipped or some dimensions are given wrong....failed to complete this drawing even though every step is closely followed
Hola, tengo una tuberia con el SolidWrorks por la qual pasa aire, i dentro hay una pelota libre. Me gustaría saber como simular el movimiento que hará la pelota en función del fluido que pasa por la tubería Alguien podría ayudarme? muchas gracias Mariona
Too call this an Air Turbo is a shame, there is nothing in this that would compress the air. Also you have two solid bodies that can't be combined and there is a wall between the bodies that would stop the airflow.
Maybe one of the worse tutorials I've even seen. To become clearer please don't change any dimensions without explain which one was modified and why you did it.
This video is not very clear
This is not how a turbo works nor is it a supercharger. This is just a swirly intake tube
THE MORE I WATCH YOUR VIDEOS, THE MORE I'M LOSING CONFIDENCE IN SOLIDWORKS.
did you change the diameter of the circle in sketch 4,because 63.5 seemed a little too big while in the video it looked smaller.could be imagining things tho.
50mm
nunca hizo un grillete , me gustaria que subiera un video de ese tipo :) saludos,
Everything was fine except last moment big circle but no hole in middle so why there is a small extrude and hole in it could be without a hole as well?
how to let the piece well??
At 7:30 when you are using the planar surface tool, I'm just getting rebuild error due to 'non planar selection or open section' any suggestions?
if you look he doesnt check it. he quits the action
It seems you enabled Realview, what graphic card you use?
I use nvidia gtx 960. Runs amazingly
hey! your videos are awesome!!! but, one question..... how can i choose the material that you use? why you piece shines?? what is the option to choose this material??? please! tellme!
ruclips.net/video/Xs_YH29ykrU/видео.html that help you pro
Sketch 4, diameter 50mm.
Thanks, man. I´s always worried about that measure hahaha
Thanks a lot!
I cant extrude cut through the middle part thing snail end
i want to have the dimensions can i ?
the boundary boss/base in 4:30 doesn't work in the same way that he does, why? I've tryed to follow each instructions, but I suppose that the conflict concerns the green line of the profile.
confirm "shell outwards"
Can't apply the third variable fillet
seems a lot of critical steps are skipped or some dimensions are given wrong....failed to complete this drawing even though every step is closely followed
I can not Planar surface. I get an error warning. Help me please
he doesnt do it. he presses x
Hola, tengo una tuberia con el SolidWrorks por la qual pasa aire, i dentro hay una pelota libre. Me gustaría saber como simular el movimiento que hará la pelota en función del fluido que pasa por la tubería
Alguien podría ayudarme? muchas gracias
Mariona
These are two seperate bodies
dude! this is not how a turbo works, where's the turbine? anyway thanks!
at 2:08 it gives me "Cannot make two planar end faces to cap the side sheet"
I have the same problem
stuck here. :/
I pratice to make a air turbo but I applied shell is take 0.5 mm , my require 1.5 mm...what is problem I take 1.5mm??
In Creo 4.0
At 9:30 my SW tell me that he can't make cut-extrude :/
same for me
what happens at 3:25?????
jajajajaja
The triangle intersect with the body
thats not a car turbo...
Too call this an Air Turbo is a shame, there is nothing in this that would compress the air. Also you have two solid bodies that can't be combined and there is a wall between the bodies that would stop the airflow.
The measurements are wrong and not clear
WHAT HAPPENS AT 0:17 ???
ruclips.net/video/M8S95QdIrV8/видео.html
1 bar jrur dekhe is bache ko
don't make fucking ellipse please !!!!!!!!
This video is terrible.
Maybe one of the worse tutorials I've even seen. To become clearer please don't change any dimensions without explain which one was modified and why you did it.