How many miles did it have? My valve cover gasket went bad at 130k replaced everything and haven't had an issue other than the valves rattle on start up. Also what did you use to snap those studs? That sucks!
I need to replace the head on mine. The exhaust manifold surface is not true and I am just going to replace the whole damn thing. My question is - Can the head be pulled with the motor still in the truck? I'm not paying a shop $3k to replace the head if I can do it in my driveway
Alexis DeVille bad valve seals from what I could tell. The oil pressure sensor went bad so I didn’t know till it was to late. My fault for not checking regularly
@@mrDelaney Thanks. I just started taking mine apart because it's getting antifreeze in the engine so I'm guessing that either the head gasket is blown or the heads blown.
@@luigiprovencher oh this will be a "series" just got the right spring compressor tool today so when I get off in the morning I'm filming taking the intake valves out. Should be a short video hope to have it up either tomorrow night or maybe Friday
Dave Cabral hey add me on insta Connor30x. Would love to see your truck. Unfortunately I’m no the guy to build your engine. I’m still waiting for mine to get out of the machine shop. But thank you
How many miles did it have? My valve cover gasket went bad at 130k replaced everything and haven't had an issue other than the valves rattle on start up. Also what did you use to snap those studs? That sucks!
I need to replace the head on mine. The exhaust manifold surface is not true and I am just going to replace the whole damn thing. My question is - Can the head be pulled with the motor still in the truck? I'm not paying a shop $3k to replace the head if I can do it in my driveway
Bro it's Clizity f****** 11.... That's brutal
You'll love my Colorado I'm from Canada it's done up I need you to have a look at it
My problem is the old bolts that hold down the ignition coils are broken inside the holes
How many miles?
first 3 minutes waste of time ., do away with the boog Music ..
Amen
Amen
Rear timing chain info or video
Just posted a video showing the balance shaft timing
You ram it out of oil and the motors is cooked, what a surprise lol
Buddy how much will you charge me to rebuild my Colorado Engine 5 cylinder?
Dave Cabral I can do rebuild your engine where you are located?
Any idea where to get forged rods for this engine?
Molnar technologies offers floating and press fit for the 6 cylinder 4.2 so I guess you'd purchase those rods and just have an extra
Ouch. Heard those head studs were a nightmare. Torqued to yield. One time use.
Yup this was the only time I messed with it. I don’t know if they have been messed with. Luckily the snapped pieces came right out with no issues
Thats with nearly all engines though. Factory bolts are torque to yield and are one time use unless you put in arp bolts or studs
How many miles were on that engine??
226xxx but it was a bad oil pressure sensor and leaking valve seals that did it in. burned up all the oil and never got a warning light
Why was it run out of oil?
Alexis DeVille bad valve seals from what I could tell. The oil pressure sensor went bad so I didn’t know till it was to late. My fault for not checking regularly
Is there a part 2?
Just posted it finally
@@mrDelaney Thanks. I just started taking mine apart because it's getting antifreeze in the engine so I'm guessing that either the head gasket is blown or the heads blown.
@@mrDelaney Is there going to be a part 3 and 4 and so on? Or is it done? What's the status?
@@luigiprovencher oh this will be a "series" just got the right spring compressor tool today so when I get off in the morning I'm filming taking the intake valves out. Should be a short video hope to have it up either tomorrow night or maybe Friday
@@mrDelaney Oh. Nice. That's cool. Thanks. How many miles were on this engine and were you the original owner?
Holler back at me
Dave Cabral hey add me on insta Connor30x. Would love to see your truck. Unfortunately I’m no the guy to build your engine. I’m still waiting for mine to get out of the machine shop. But thank you