Hi John, another hack I use is to put a Q-tip shaft, without the cotton, in the spring. That worked most of the time then decided to turn the lower ring of the spring 1/2 turn which keeps the upper ring of the spring to the left side of its hole, like the cotton top on your way, problem no more on my machine. YMMV.
Since the whole is already there, I'd use a drill press and enlarge the whole and then thread it. It ensures the bolt you use will have a large enough face to allow the stem to sit flat and firm again it. Then you can ensure that the end of the bolt is completely flat. Also you can just use 1 thousandths' flat washer/rings inside to act as a shim. Using 1 thousandths "shims" is all that is needed. You can just count how many shims you need. Then you don't have to tap the whole if you don't want to. Or add the shims to the bottom of the stem and super glue them in place. There are tons of ways to skin that cat. Dang... now I want Chinese food for lunch. I wonder why? ;)
Great Tips for modding the Lee ACP! What I want to be able to do is load primers in the ACP press to 0.000 flush depth, then come back with a precision hand primer tool, to set the final depth. If I could skip manually handling the primers one at a time, it would make hand seating primers much faster. It would be great if this ability came already machined into the press. Are you listening LEE PRECISION? If my hardware store has a 5/16 - 32 threaded bolt and lock washer I'd choose that route and buy the tap for that. This would give more precise control over seating depth below 0.003. Most factory brass comes with primer pockets that are made to the minimum SAMMI spec. with that the 0.002 - 0.003 depth is optimal. Not all brass conforms to the same depth. Some people use primer pocket uniforming tools to cut the all the primer pockets to maximum SAMMI spec. This changes the optimum primer seating depth to about 0.008 - 0.009, with SR/SP pocket.
Glad you liked the tips and hope they help. I have another APP/ACP videos coming where I show how to make it adapt for magnum calibers with a few simple parts.
@@FClassJohn I have the APP press on order and I'm going to add the ACP press after seeing your mods. Thank You! I'm glad to see the ACP press compete against the primal rights unit that costs $650.
The O ring from the Lee die lock ring also fits on the upper die body & holds it in place. I found that out after launching mine into orbit a couple of times 🤣
Great info. !!......I believe, no matter the cost, ....inexpensive to high-dollar, tools/equipment/machines always require & or so desire a few personal tweeks to benefit the user, - good tweeks imo - Thanks fer sharing.
Hello John - very Impressive priming tool, from LEE no less - I see they say it can only take up to 2-2.5 inch cartridge cases - is there a way to modify this for longer cases - specifically: 338 Lapua ?
I thought you had one of those high dollar CPS primers from Primal Rights? Did it not work out for you ? That you went with this cheaper more affordable solution from Lee?
I was using the CPS and it’s a great unit but for me having the ability to hook up my casefeeder to the Lee was a big deciding factor for me. I’ve been really happy with the switchover and have since gotten rid of the CPS.
I don't have either to try but I think it would be close. It says it can prime cases up to 2.5" but you'd have to do it by hand for sure on the PRC, maybe on the 30-06.
Not sure if you are still using this to prime but Lee has an upgrade kit for the primer feed. I didnt want to post a link - ACP PRIMER FEED UPGRADE KIT Upgrade your ACP Primer Feed to the 2023+ Deluxe APP Primer Feed. SKU: 92046- Happy to see this as I have gone through 5 of the PRIMER TROUGH & TORSION SPRING -Lee send has sent these free of charge when I ordered. So I assume they knew it was an issue.
@@FClassJohn Got this up and running. It works but you need to change your rhythm in order not to short stroke being the primer is forced into place.. Might be worth a video. As its a pretty cool design.
@FClassJohn I'm looking at the deluxe now. I may just go back to priming on my press now for the moment and see what happens. I switched off to an rcbs hand primer a couple of years ago, and it's almost like I've been chasing my tail ever since trying to stay consistent. I seated a few primers on my press last night and every one of them was .0065" below flush. .007-.009" seems to be the spot most shoot for. If it doesn't pan out I'll order tye deluxe app.
Hi John, another hack I use is to put a Q-tip shaft, without the cotton, in the spring. That worked most of the time then decided to turn the lower ring of the spring 1/2 turn which keeps the upper ring of the spring to the left side of its hole, like the cotton top on your way, problem no more on my machine. YMMV.
Thanks John i think I'll go this way instead of the primal rights one
Since the whole is already there, I'd use a drill press and enlarge the whole and then thread it. It ensures the bolt you use will have a large enough face to allow the stem to sit flat and firm again it. Then you can ensure that the end of the bolt is completely flat. Also you can just use 1 thousandths' flat washer/rings inside to act as a shim. Using 1 thousandths "shims" is all that is needed. You can just count how many shims you need. Then you don't have to tap the whole if you don't want to. Or add the shims to the bottom of the stem and super glue them in place. There are tons of ways to skin that cat. Dang... now I want Chinese food for lunch. I wonder why? ;)
Great Tips for modding the Lee ACP! What I want to be able to do is load primers in the ACP press to 0.000 flush depth, then come back with a precision hand primer tool, to set the final depth. If I could skip manually handling the primers one at a time, it would make hand seating primers much faster. It would be great if this ability came already machined into the press. Are you listening LEE PRECISION?
If my hardware store has a 5/16 - 32 threaded bolt and lock washer I'd choose that route and buy the tap for that. This would give more precise control over seating depth below 0.003.
Most factory brass comes with primer pockets that are made to the minimum SAMMI spec. with that the 0.002 - 0.003 depth is optimal. Not all brass conforms to the same depth. Some people use primer pocket uniforming tools to cut the all the primer pockets to maximum SAMMI spec. This changes the optimum primer seating depth to about 0.008 - 0.009, with SR/SP pocket.
Glad you liked the tips and hope they help. I have another APP/ACP videos coming where I show how to make it adapt for magnum calibers with a few simple parts.
@@FClassJohn I have the APP press on order and I'm going to add the ACP press after seeing your mods. Thank You! I'm glad to see the ACP press compete against the primal rights unit that costs $650.
How did I miss this 2 weeks ago?! Glad to see you making the Lee work, I love mine but definitely needs some modifications
The O ring from the Lee die lock ring also fits on the upper die body & holds it in place.
I found that out after launching mine into orbit a couple of times 🤣
Great idea
This is great content. Thanks for sharing 👍
Brilliant!
Love it keep uo the good work. If your ideas work then please share them.
Another great video keepem coming brother!!
Thank you
Great info. !!......I believe, no matter the cost, ....inexpensive to high-dollar, tools/equipment/machines always require & or so desire a few personal tweeks to benefit the user, - good tweeks imo - Thanks fer sharing.
My pleasure and glad you liked it.
Hello John - very Impressive priming tool, from LEE no less - I see they say it can only take up to 2-2.5 inch cartridge cases - is there a way to modify this for longer cases - specifically: 338 Lapua ?
Take your time
Do you know if the APP will prime in the same fashion as the ACP?
Cool I'll try thix
I thought you had one of those high dollar CPS primers from Primal Rights? Did it not work out for you ? That you went with this cheaper more affordable solution from Lee?
I was using the CPS and it’s a great unit but for me having the ability to hook up my casefeeder to the Lee was a big deciding factor for me. I’ve been really happy with the switchover and have since gotten rid of the CPS.
@@FClassJohn I was wondering the same thing lol. Glad to see you can still do primer seating without having to spend that crazy amount.
I just use factory 3,000. Do you have a problem with jamming on the rim holder for 9 mm? Anyone got a fix?
Would a long action case fit even if you were single feeding? Something like 30-06 or 300prc length cases?
I don't have either to try but I think it would be close. It says it can prime cases up to 2.5" but you'd have to do it by hand for sure on the PRC, maybe on the 30-06.
John ... Could i use this for 338 lapua cases
I honestly don't know and they've discontinued this product and replaced it with this amzn.to/4b6u7Oq and it says max of 30-06 length.
Not sure if you are still using this to prime but Lee has an upgrade kit for the primer feed. I didnt want to post a link - ACP PRIMER FEED UPGRADE KIT Upgrade your ACP Primer Feed to the 2023+ Deluxe APP Primer Feed. SKU: 92046- Happy to see this as I have gone through 5 of the PRIMER TROUGH & TORSION SPRING -Lee send has sent these free of charge when I ordered. So I assume they knew it was an issue.
That's good to know. I'm priming on my 750 now but that was definitely a trouble spot so glad to see they have a bit of a fix.
@@FClassJohn Got this up and running. It works but you need to change your rhythm in order not to short stroke being the primer is forced into place.. Might be worth a video. As its a pretty cool design.
Could you do .338 lapua on this?
Possibly if you feed one at a time but it’s only designed to feed non-magnums up to 2.5” long.
The acp is discontinued, have you ever primed on your app ?
It's not possible. You now have to get the APP Deluxe but I haven't used it.
@FClassJohn I'm looking at the deluxe now. I may just go back to priming on my press now for the moment and see what happens. I switched off to an rcbs hand primer a couple of years ago, and it's almost like I've been chasing my tail ever since trying to stay consistent. I seated a few primers on my press last night and every one of them was .0065" below flush. .007-.009" seems to be the spot most shoot for. If it doesn't pan out I'll order tye deluxe app.
Why would the primer hole be that deep anyway?
Because you can attach a bottle to collect spent primers when decapping.
So do you still use your primal rights unit?
No I stopped using it once I switched to this.
@@FClassJohn better value. I might need to get one.
Iam new to this, what type of gauge are you using and where do you get it?
It's this one bullettipping.com/2018/05/accuracy-one-precision-primer-gauge/