Easy DIY Pourable Marine Foam
HTML-код
- Опубликовано: 25 авг 2024
- How to use Pourable Marine Foam
We used 2 pound density pourable foam to add flotation and rigidity under the deck of a 13 ft skiff. Learn how to best mix, what size hole to drill and how to warm up the under deck space for best results. This 2 lb density expandable boat buoyance foam not only adds flotation but also structural rigidity but can also act as insulation and sound proofing.
Check out our other DIY projects www.DIYeasycrafts.com
Blue Dayz Apparel
www.bluedayzgear.com
Facebook
BlueDayzGear/
Instagram
Blue_Dayz_Fishing
Update : After filling a 18 foot boat was about three quarters complete and then someone from a boat group suggested using one gallon zip loc freezer bags to mix and pour then cut the corner and squeeze out the foam. This was a game changer ! . I saved cost of measuring cups and used clean water bottles as my measurement then poured part one then part two into the bag and rolled it to mix. This gives much more time to mix as there is little to no air to start the process and I was able to squeeze almost every drop out of the bag.
Use a piping bag instead, even better!
Definitely the best how to video on you tube . Thank you for taking the time to do this Sir.
You are very welcome and I really appreciate you taking the time to provide feedback. Good luck with your project
I am restoring a 1964 Johnson Sport 135 Evinrude. Tri hull . Omg ! The floor was a little rotten and very wet it sat outside for 20 yrs. I just stripped out floor and the foam and some small repairs on the hull but watching your video I can go tackle the floor. Good information.
What an excellent, interesting and informative tutorial this is!
I particularly liked that you kept the fibreglass plugs and refitted them with self adhesive tape and weighed them down to keep the foam from expanding out of the hole.
This is clearly beneficial as the foam adheres to the fibreglass plug (which presumably is then further reinforced and sealed with epoxy or thickened epoxy when fully cured).
The other advantages of this is that no foam is wasted and there is less time, effort and materials used to clean up protruding streams of cured foam!
Other than the foam used to show viewers the expansion rate at the beginning of the video, this an especially good method of managing uasge and minimising wastage.
I believe that where the liquefied foam mixture is being poured into small, closed cavities one would not plug the expansion, as unlike in this large, open cavity, the expanding foam has nowhere to go and may well fracture the plywood joints as the confined foam continues to expand! Subscribed.
I was originally thinking of using several 8' x 4' x 6" closed cell foam boards laminated between sheets of marine plywood to form a buoyant platform on which to mount a Slidavan, but this method is definitely worth looking into.
Thank you very much. This was a fun project. Temperature is critical or the foam will not rise
I have watched other videos and this one is the best so far. Thank you
Wow, thank you!
Thanks. I will be using this on a P D Racer in the spring. Much easier than cutting foam sheets to fit.
Glad to help
Good job, we've used this system to fill any voids in the cool rooms we've built.
Thanks for sharing sir. The amount of possible upgrades you can use this stuff for is endless. Its always been my intention to add this to the inside of my aluminum hull to prevent it from sinking if I ever holed it going up some river somewhere. I bet it makes a usefull sound barrier too.
Most aluminum hulls are only single sheets without a void that could be filled with foam. You could do it by adding a non structural raised deck. You are 100% correct this stuff would offer a great sound barrier
.
awesome process. looks like a lot went into the planning process. I will follow this procedure for my next project
.
bravo!
.
Good luck!
Very nice. I will add this inside my kayak since I will be putting a trolling motor and big battery and it will make it very heavy.
Great tips. I'm about to foam my 16' StarCraft.
best of luck
Hi from Oz, a very helpful video, thankyou for sharing.
Glad it was helpful!
Excellent video I’m about to pour this under the front bedroom floor of our NAUTALINE 43. I was worried about the expansion force pushing the deck up. Your plugs showed how little force there was. Thanks.
Glad it was helpful!
THANKS for making is so simple!!!
You bet!
Awesome video Thanks 👍
Glad you enjoyed it
@@DIYeasycrafts I did it was very satisfying and straight forward !
And I looked on your channel and Now have bought my first knife blanks. I guess that's what retired folks are to do anyways lol 👍 Again thanks for all your content !!
Great video. As an added note it is not just air temperature but product temperature also. The temperature of the product should be above 70 degrees to help promote the proper chemical reactions.
Great point!
I have an old crews craft with a rotten floor. I would realy love to turn it into a self bailer. Thanks subbed -PawPaw
Best of luck with your project.
Thank you!
Good video, but there is no mention of what brand foam is being used.
My plan is to try and pour this stuff into an inflatable sponson for a RHI that keeps leaking in one chamber. It is 24" in diameter and 5-feet long.
Super curious question, & I think it would make for an awesome video.
That is if it can be done.
Anyway I was curious to what you would think. Do you think that this could be poured into a raft? I’ve always wondered if I did this kind of mixture & poured it into an Air Raft if it would expand & take the shape of the raft & then harden. I’ve even thought about if this would work with those kids blow up air swimming pools, or those air hot tubs.
I first had this idea when I worked construction with my uncle back in the early 1990’s. I was using spray foam insulation & thought it was the same as marine insulation. Then my uncle told me the differences about them.
Anyway I would very much like to know what you think.
Also I liked your video, it was very well done & informative.
I thought of this too, as I tried to fill the ring of a pool with great stuff and found that type of foam needs open air to rise and cure. This, if it does in fact, do well in closed spaces would be cool to fix leaky rings in pools as it adds buoyancy. I ended up filling the ring with pool noodles and little Styrofoam beads then sealing with duct type & silicone. Lasted the summer but man was she ugly.
thanks for sharing sir :)
My pleasure
Maybe you can store both urethane buckets in fridge, to increase the pre pouring time during warm weather
Question: What would happen if you misjudged the amount of foam required to fill the void and put too much foam into the void?
The excess foam will take path of least resistance. It will push out the predrilled fill holes .
I have a idea to make a raft out of 18 gallon bins, I want to use foam to seal the tops of the bins to the bottoms then bolt them to the bottom of my raft.
I know this would work for keeping water out.
But if i filled them to the brim would it increase the buoyancy of my bins?
No foam will not increase the buoyancy but it would prevent water from leaking in and filling the bins. If leakage it would maintain bouyancy.
Greetings. This is a GREAT video. Taping the plugs over the holes is great. Question... Im restoring a 13 ft classic Boston Whaler. What was your process cutting out the floor? Did it come out in pieces? It looks like you removed, then reglassed the seams before foaming. How thick is the floor? Was there wood under it? Mine is a 1972. Thanks much!! Steve from Canada.
I had a Dell Quay dory so whaler might be a little different. I was able to remove large sections of the deck, Only wood was a couple stringers. Deck was thin fiberglass it only became rigid once supported by the foam
@@DIYeasycrafts Thanks so much!! Your videos are amazing. You are a super smart guy obviously. Lots of great tricks and tips.
Did you have to level the boat when you pored the foam
Any fumes ? Need to wear a mask ? Great video 👍
I want to fill up thin walled pvc for dual kayak pontoons. Going for a hobie island adventure pontoon and trampoline.. how much 2lb density for 2, 6 inch diameter 10 foot long pipes?
I have a question, do you know how much kilos u used? Moreless how much cubic meters can you fill lets say with 10kilos of urethane moreless of course. Thanx
im sorry but I do not. Best bet would be to contact the manufacturer
I’m think about filling my paddle board with this do you think this is possible
Question: was one gallon of each part enough to complete this project or did you need more ? Thanks
I bought two and had extra. Only needed a little more than on gallon
Great video very educational I’m currently restoring a 78 sea nymph aluminum I stripped her out foam was was no good, but for the most part the aluminum was solid. Now I’m trying to figure out how I should go about ?? I was think put the floor in section tilt her upwards much as possible and pour it. If it fills up the section immediately add another section to the floor tac it down repeat. Any feedback for me? would highly appreciate it.
Fish on thanks I subbed as well.
Never worked with aluminum but would think you might need more than a tack weld. This stuff will push itself out any opening. if it can not find a way out it will buckle the floor upward. Im assuming you want to stay away from drilling pour holes in the deck. Probably a good Idea because it would be hard to weld each closed with out burning the foam. I think your idea to tilt forward as much as possible is great. Only thing I would do is complete deck welds instead of tacking
@@DIYeasycrafts i will not be using aluminum for my deck I’m going with ply 5/8 maybe even 1/4 being that the foam once poured will create a solid backing reinforcing the flex on ply. Now that you know it’s plywood any different advice? Thanks for the response. Fish on!
I'm in the process of restoring a sea nymph aluminum boat. Roughly how many gallons of 2 part foam do I need for a 16 foot hull?
Where can I buy this at
I might have miss something but:
- any links to the product?
- i need to fill 55 gallons drums: hie many would it take?
Call totalboat.com they have techs that will be able to answer your questions
Great! thank you. Just what i was looking for. Question, what was the condition in inside the compartment before your poured? I will be attempting to do this on a 23 ft power boat that had a water logged hull and cracks that have now been repaired.
Since I had to cut out the deck to remove the wet foam was able to clean the entire surface with acetone and sand with course grit disc sanding wheel. I wanted the new foam to bond to it
Temperature is critical. Not sure where you are located but make sure its warm enough!!
Could you mix this expanding foam with styrofoam for a cheap and quicker filling?
I guess but Styrofoam does not have the same durable characteristics as closed cell foam does. It would just be a space filler that might break down or absorb water over time.
Adding foam doesnt "add flotation to your hull"... it actually makes your hull heavier, and cause your hull to float deeper below the water line. It's only "additional flotation" if you crash :)
thats why people should only do this if the boat is designed with foam. sealed chambers and scantlings and all that... not as an addition to non foam hulls. (it'll mess with the waterline and efficiency)
!!!! if you damage your hull on a coral reef water will get in but if your hull is filled with cork sheet which is extremely light how water can get in & fill the hull ? theres no room ?
It seems like foam is not a permanent solution for filling voids as there appears to be common to absorb water.
It can be you just have to make sure water has no way of getting in
Has anyone used this stuff for attics?
I have a few questions i have an aluminum bass boat i want to fully foam the entire underside of my front deck im worried about the foam expanding too much and blowing out the bottom or sides of my hull. Can you add any insight to this am i correct or incorrect in my concern
The foam will take path of least resistance. If you have pour holes you could always let it overflow the hole and then trim it back and patch. (not as easy with aluminum).
@@DIYeasycrafts but what about when it fills a cavity then expands?
My question is will it expand and make my hull stretch? Or will my hull do as a form and be rigid enough to hold its shape?
Thanks for this well made video. What are your thoughts on using this product to fill the pontoons of a houseboat? I have a 1967 houseboat with old, steel pontoons that leak. The pontoon is separated into compartments, with each compartment having about 30 cubic feet of volume. Would the urethane foam fill the whole compartment, seal the leaks/holes, and remain waterproof over time and not absorb water?
It would fill the compartment but it would squeeze out any of the leaks. I do not think its made to be in direct contact with water all the time. I would fix the leaks then fill with foam
So just a dumb idea...but would this work for filling like an inflatable chair? Lol I know sounds ridiculous but my kids cat is gonna pop this cheap chair that he is so proud of buying.
No I do not think so. Foam ends up being very hard and its a l;ittle expensive for that type of project
How many cans did you end up using?
2 gallons
How many pounds density do you used?
I’m about to do a 16 whaler. How much foam did you use?
Not really sure. I did a 13 foot dory with 2 gallons. Would think you will need at least 4
@@DIYeasycrafts, What is the name of it and How Much does it Cost Pls
? .. Thanks, Richard
Comment
How much did you use
2 gallons
But with a sealed floor you don't even need foam for floatation right?
The foam not only adds floatation but also rigidity. This boat actually has very thin fiberglass. It needs the rigidity
How much and how to order?
I got it at local fiberglass supply distributer. Qty depends on size of boat and thickness of void
How many gal did you use
It comes in two parts I think I used 2 gallons but had quite a bit left over
@@DIYeasycrafts how many square feet was the deck?
So outside of the obvious of making a hard job harder. Why isn’t anyone using plastic bags to put foam in hulls to protect from water saturation. Even closed cell foam will become water saturated in a couple of years with no where for the water to go. This question is more for unsealed decks than sealed of course.
❤️✍️☕☕
Don't you use your stick to get all the product out !!!!!?????
This stuff is seriously toxic in use and can emit toxic fumes ongoing... not for inside your living area on the boat. Also flammable and emits deadly smoke when it burns. Just sayin..