One way to check for wobble is have quad on a hard, smooth flat surface, and stand next to quad. Using one hand grab hold left or right handle grip and try to move up and down, like your going to lift the quad. If you feel play it’s your swing arm bearings. Then slightly move front to back with same hand, if there’s play before your tires start to turn, then it’s your steering. No play in any direction then your bearings are good to go. Check using this method frequently after your riding adventure you will be able fix a bearing issue before it goes out. If one tire is just wobbling, get said wheel off the ground and move it back & forth, up & down to check wheel bearings and axle bearings as well. Also spin wheel by hand and you may see out-of-round rim. I would also check lineament of chain and lineament of both sprockets. A common laser pointer works best by holding it next to and on top of chain. A yard stick will work too. When riding and If you smell something strange that’s not oil or rubber or melting plastic, then chances are your brakes are hanging up. Uneven brake pad wear can be caused by improper replacement and/or brake rotor out of shape. Cheap brake rotors can heat up quickly and distort rotor. Riding in mud, sand or dirt will gouge rotor over time, which will be noticeable by grooves on sides of rotors. Disconnecting rev-limiter could cause over rev-ing and may damage the motor, use caution when flying down the road, I’ve seen lots of motors go pop!.
My 07 SE with Big 3 (Dasa Duals, FCI, MSD) with 21 inch street tires and 15t sprocket hit 88mph. That's with the rev limiter intact at 1000' elevation. GPS verified on three runs. I did the same test before the 15t and I went from 84 to 88 top speed so +4 mph gain. Where I noticed the biggest difference was on dirt. It hooked better with the 15t.
Careful with that purple power. That stuff can eat threw rubber if you leave it on too long or don't clean it up well. But yeah any degreaser & some magic erasers, even the off brand are a beast at cleaning motor & plastics of grease or wax buildup.
If you want more speed less wobble change the tyres to road tyres. I recommend Kenda speedracer. Go for larger back tyres. Bigger fronts too. It will be more of a road quad then. The quad wont corner as well but thats the price you pay. Put your air box lid back on and take your baffle out. At stock I was getting 88mph I'm 20stone. Alternatively go twin pipes power commander new air filter. You should hit over 100mph easy but it will sap your fuel adding these extras.
Hi there I have a raptor 700r 2006 and have a issue with it .the like previously had a 12t front and 38t back sprocket although I changed the front sprocket to a 15t .the bike was running good although I experienced a problem with the bike loosing rev at high speed so I adjusted the tps sensor and the bike came right although when the bike had its previous 12 and 38 set up the speed topped out at around the high 30s around 130. Now with a bigger front sprocket I'd expect to have more speed although now the bike stops at around 114km/h .I've removed the clutch sensor to bypass the top speed limiter although the bike still stops at around 114.The bike has a set of 22s in the back Just to refresh the problem When I had 12t and 38t sprockets and a 21inch tire the quad topped out at 130 above When I added a 15t front sprocket and 22inch tires the bike tops out at 114 The only thing I did in between was set the tps sensor back to specifications of 0.68 as it was on 0.77 and with full throttle around 4.10 Any ideas why my top end is so low
I had the same issue with a front tyre. Chinese tyres need balancing. Oh yer my 2007 does over 95 if you can keep it in a straight line. Need a smooth road though and that's with standard 14/38. I have no idea what engine mods this one is carrying. Definitely exhaust and intake. The PCV has been taken off. The starter stalls for a second so it might be running hi compression. And it doesn't like low octain gas. BUT it's a lot lot quicker than a standard machine.
If the guy bent your rim you would probably feel it going any other speed but it could just be the tread worn uneven like a jeep death wobble or something but it's a beautiful quad I've been looking to get one like that
I have the same issue with the rear brake caliper. I was changing the tires to some maxis rzr 2s and when I was rotating the axel I noticed the caliper rubs on the brake in 1 odd spot. It's weird that both of our 2015 Raptor 700s do that.
BuffaloGino hi i hope this helps, i went on a ride and was driving around and went through a puddle. This cooled the rear disc and warped the steel, it caused an uneven surface and disc to be totally ruined
Hey I have a 2017 Raptor 700R and i did a few mods and got mine running 90mph without disabling the rev limiter. I changed my sprockets front 15T rear 36T. I am running HMF Blackout Exhaust with the HMF Optimizer. For more stability I bought the Tusk wheel hub extension not the adaptor that goes over the factory stubs. Also I installed the GYTR air filter and left the air box cover on. I guarantee a quick fast response after these mods. Let me know what you think after you try it.
Have you removed your baffles in your exhaust if not take a flash light look on your pipe you will see a super restricted baffle there are two inside your exhaust you can remove them with a 2 1/2 lb hammer and a long standard screw driver i did this to mine 16' then put a monster tip on it i recommend getting a fuel controller if you do this though to richen it up a little
hey raptor man, do you feel like your front end is extremely stiff? just curious, my 2015 700r feels very stiff and I'm 3 clicks up from the lightest possible setting and I'm 220 lbs just curious what you think? I know they went with a heavier spring for 2015 and 16, my last qaud was a 2005 troy Lee predator and I feel like the front end was alot smoother when it came to choppy stuff.
you know I'm really not sure. I haven't adjusted the springs at all yet, (I'm 270) but I prolly should. As far as the front end bro this is my first raptor so really idk. I do know I need to stiffin up the back to hold my fat ass tho lol when I get on it bitch turns to a low rider lol
+RaptorMan2016 I have a yfz so mine only hits 72. Stock sprockets but I got a vortex ecu and full exhaust with intake mod. But nice raptor man. I had a 700r before my yfz and I hit 78 at the most
sprockets and gearing aside...taller back tires will increase you overall top speed assuming your have enough ponies to turn them. Just like throwing smaller tires on there decreases your gearing slightly... so theoretically with 22s on there you can do higher top speed than with 18s or 20s bolted on in the rear but it might take the quad longer to get to top speed with the heavier 22s.
+WarWizard Productions that's awesome. I've been working so much I haven't uploaded. I have a trip planned for September 15-18th so expect some real good videos coming soon.
I hit 79mph I'm 6'1-280 on my 2017 Raptor 700r SE all stock. Does ur fan make a buzz noise when it cranks on to cool of the engine? mines sometimes makes it and sometimes it quiet
My fan kicks on quite a bit on mine, it's a 17' just got it about a month ago, is this normal? Every other person I know who owns one it rarely comes on. Idk
Sounds like the beads are not seated onto the rims . I had some tires on my 4x4 I had to lube and air up to about 60 psi to get them to seat. I also have a 06 raptor 700 with a 4in extended swing arm . It was 1 of the first ones that had a problem with the fuel pump,it would run rich and flood. They told me I was riding it too slow, meanwhile no one could keep up.lol. I ended up taking the restricker out of the muffler ,had not had any problems since. Its been the best bike I have had.
when I first got the tires back the guy said the had 6psi in each, come to find out there was really 20+psi lol I will give that a try as well. they are great bikes, love mine. thx for the info
no I think the defective fuel pump makes it really rich . So when I removed that baffle it was like I put a controller on it and a pipe. I almost sold it because I was pulling wheelies in 5th gear not trying. after I put the swing arm on it was a totally different bike. Only problem it was harder to turn. Im not a bike tech but im a ase master tech for automotive repair.
@@RaptorWRLD That sucks. The conversation on my 2018 Raptor is doing the same thing. There's gotta be something out there that will clean it rather than having to powder coat it.
I hit 87mph stock gearing and big 3 mod .200lbs rider. Also I use engine ice in my 2015 700 I have a vapor trail tech and my temps stay a average 10deg cooler then with regular coolant.
+RaptorMan2016 from what I've read a single exhaust works better on the single port heads. I have gytr intake w/Ehs lid, Ehs racing programmer , fmf power bomb header and fmf power core exhaust and the power gain is extremely noticeable pulls like a freight train.
Also, pulling the airbox lid off is creating a lean condition which is why you are running hotter than usual. I would recommend just leaving it on or putting a fuel controller on it so you don't damage your piston.
I would hate to see something let go in your motor from something so simple. When you order your exhaust (if you order one) just order a big 3 kit from tqsatv, he will map the pc3 or pcv for your quad.
+1 did PCV and FMF slip-on this weekend on my 2016. runs way cooler and tons more power. don't jack around with anything man, do PCV first. just plugging it and flashing it in makes a huge difference.
nah I tried that. my buddy said there is an adjustment and the axle he did the same thing and he said they are shims inside the carrier that I can adjust
09 780kit stroker crank stage 3 cam factory 4 exhaust Take the cam chain cover and have it painted with high temp paint or powder coated... two bolts. Put your airbox back on that is horrible for your stock head. Let me know if u wanna see my quad
Not bad 82 MPH, and to clean it use Purple Power and a a Tooth Brush. No joke. New tires will be like that at first. Mine was HORRIBLE it was almost not Controllable at all when I first put on my back tires. It's all of those little "Fingers" the molds on the tires once those wear off it will be good, is it almost as if you're riding on Slime?
take a plastic 99 cent store brush like for doing dishes, chop the end off and stick it on an electric drill. works great for cleaning those tight areas. Dawn dish soap mixed really heavy with warm water is the only thing I use on my quads. I have used the purple stuff too works great but it will melt your hands if you get it on you lol.
The comment was mostly directed to people getting into this. Seems like it's the new owners that have engine issues. Thanks for the efforts behind the content.
@@joshbrown1381 i guess im a new owner in a sense lol only been riding the 700 three years. if my bike breaks thats on me, i ride this thing too hard not to. i know who to call when that happens.
@@joshbrown1381 i wish i could film more, but life gets in the way unfortunately. the powers that be keep me away from what i love. hopefully i will get you some more content soon.
I'm a pre new owner. Lol. Disregard if I sound like an expert. I know vehicle brakes, driveline and transmissions. I am learning about bikes and quads currently. I'm finding in life you need to make the time for yourself. If you let it, life/society will drain you of all your time.
Be careful running with no air box lid without a programmer. The full injection can't keep up with that amount of air increase. That may also be why it was heating up, its leaned out to much. i did this to my 08 and it didn't like it. i put a k&n on and put the cover back on until i do my exhaust and programmer.
no worries my dads got the 2006 700 with the full DMC afterburner exhast system probably one of the loudest and meanest sounding pipes ive ever heard ahah
Bro unplugging the cable is not enough - You have to jump or solder the connections together. It will let the ECU think it is always in Neutral disabling the 5th Gear limiter. Removing the plug is the same.
I searched all over on the subject. You have to connect the wires together as if youre pressing youre clutch lever continously. The ECU will think its in neutral and disable 5th gear limiter. 85mph is stock speed. Tuned Raptors go faster without limiter.
- First of all, what's you name bro? - You really wanna get your quad going faster than 82mph? I think it's quite enough for off-road quad (it's not street legal) and crashing at that speed is not that fun (especially with wobbles wheel) :P - It's not dangerous to disable the rev limiter? you can more easily kill your engine, no? - I think I had the same issue that you have with your rear disc brake and I had to replace it with a new one. upload a video of it, it's interesting to see what is all about. - Riding 82mph with shorts and not protection gear?!?! you are a lunatic bro! haha. - I like your quad (;
My name is RaptorMan or you can call me Josh xD Disabling the Rev limiter will cause damage to the valves easier yes, but I don't care lol yes eventually I plan on putting a turbo on this bike so 82mph for me is not good enough. My old 1998 Banshee did 88mph so I would like to see this quad go faster than that. The brake issue sucks really weird.
Huh I put 22 inch rear tires and 23 inch front tires on , K an N air filter, rejetted both carbs, Bills pipe, FMF muffler, 16t front sprocket , 37t rear sprocket, on a 2002 ,and it would run 100 mph and not overheat
hey man whats up i have the same raptor it has an full akrapovic exhaust and it it limits at 105 km/h and the gears are to short do you have any social.mefia than we can talk thank you
awe man try this for a smokin' hot machine. drain all the fluids outta your quad it'll be sooo much lighter you'll def hit 90mph. also replace all your wires with the smallest gauge possible to make your computer go into high horsepower mode and your sparkplug will fire hotter.
If you want more speed less wobble change the tyres to road tyres. I recommend Kenda speedracer. Go for larger back tyres. Bigger fronts too. It will be more of a road quad then. The quad wont corner as well but thats the price you pay. Put your air box lid back on and take your baffle out. At stock I was getting 88mph I'm 20stone. Alternatively go twin pipes power commander new air filter. You should hit over 100mph easy but it will sap your fuel adding these extras.
Авто/Мото
One way to check for wobble is have quad on a hard, smooth flat surface, and stand next to quad. Using one hand grab hold left or right handle grip and try to move up and down, like your going to lift the quad. If you feel play it’s your swing arm bearings. Then slightly move front to back with same hand, if there’s play before your tires start to turn, then it’s your steering. No play in any direction then your bearings are good to go. Check using this method frequently after your riding adventure you will be able fix a bearing issue before it goes out. If one tire is just wobbling, get said wheel off the ground and move it back & forth, up & down to check wheel bearings and axle bearings as well. Also spin wheel by hand and you may see out-of-round rim. I would also check lineament of chain and lineament of both sprockets. A common laser pointer works best by holding it next to and on top of chain. A yard stick will work too. When riding and If you smell something strange that’s not oil or rubber or melting plastic, then chances are your brakes are hanging up. Uneven brake pad wear can be caused by improper replacement and/or brake rotor out of shape. Cheap brake rotors can heat up quickly and distort rotor. Riding in mud, sand or dirt will gouge rotor over time, which will be noticeable by grooves on sides of rotors. Disconnecting rev-limiter could cause over rev-ing and may damage the motor, use caution when flying down the road, I’ve seen lots of motors go pop!.
My 07 SE with Big 3 (Dasa Duals, FCI, MSD) with 21 inch street tires and 15t sprocket hit 88mph. That's with the rev limiter intact at 1000' elevation. GPS verified on three runs. I did the same test before the 15t and I went from 84 to 88 top speed so +4 mph gain. Where I noticed the biggest difference was on dirt. It hooked better with the 15t.
15t he give more speet
Careful with that purple power. That stuff can eat threw rubber if you leave it on too long or don't clean it up well. But yeah any degreaser & some magic erasers, even the off brand are a beast at cleaning motor & plastics of grease or wax buildup.
If you want more speed less wobble change the tyres to road tyres. I recommend Kenda speedracer. Go for larger back tyres. Bigger fronts too. It will be more of a road quad then. The quad wont corner as well but thats the price you pay. Put your air box lid back on and take your baffle out. At stock I was getting 88mph I'm 20stone. Alternatively go twin pipes power commander new air filter. You should hit over 100mph easy but it will sap your fuel adding these extras.
Wish I had the money to get a raptor 700r they look so fun and it looks like it's worth the money
Wheel brite Acid wheel cleaner cleans aluminum VERY EASY AND FAST! 2011 YFZ450R
Thank you will give it a try
msd blaster. intake full exhaust, you be hauling
Hi there
I have a raptor 700r 2006 and have a issue with it .the like previously had a 12t front and 38t back sprocket although I changed the front sprocket to a 15t .the bike was running good although I experienced a problem with the bike loosing rev at high speed so I adjusted the tps sensor and the bike came right although when the bike had its previous 12 and 38 set up the speed topped out at around the high 30s around 130.
Now with a bigger front sprocket I'd expect to have more speed although now the bike stops at around 114km/h .I've removed the clutch sensor to bypass the top speed limiter although the bike still stops at around 114.The bike has a set of 22s in the back
Just to refresh the problem
When I had 12t and 38t sprockets and a 21inch tire the quad topped out at 130 above
When I added a 15t front sprocket and 22inch tires the bike tops out at 114
The only thing I did in between was set the tps sensor back to specifications of 0.68 as it was on 0.77 and with full throttle around 4.10
Any ideas why my top end is so low
I had the same issue with a front tyre. Chinese tyres need balancing. Oh yer my 2007 does over 95 if you can keep it in a straight line. Need a smooth road though and that's with standard 14/38. I have no idea what engine mods this one is carrying. Definitely exhaust and intake. The PCV has been taken off. The starter stalls for a second so it might be running hi compression. And it doesn't like low octain gas. BUT it's a lot lot quicker than a standard machine.
Diego et 700R son conseiller à quel âge 16 uo 18 uo 20 ?
Purple power works great for stuff like that
I recently installed a set of brand new holeshots tires and I have a wobble at speed also. I have no idea how to fix it...
yea I'm clueless bro
Any problems with the case saver with the biger sprocket ?
yes had to shave it down alot, might just remove it altogether.
If the guy bent your rim you would probably feel it going any other speed but it could just be the tread worn uneven like a jeep death wobble or something but it's a beautiful quad I've been looking to get one like that
Yea I've since fixed it. Parking brake was partially engaged.
And thx for the compliment:)
Sick bike
thx bro!
I have the same issue with the rear brake caliper. I was changing the tires to some maxis rzr 2s and when I was rotating the axel I noticed the caliper rubs on the brake in 1 odd spot. It's weird that both of our 2015 Raptor 700s do that.
I might have figured it out bro. my parking brake (even though not on) was still on lol I loosened it up I think the wobble is gone
BuffaloGino hi i hope this helps, i went on a ride and was driving around and went through a puddle. This cooled the rear disc and warped the steel, it caused an uneven surface and disc to be totally ruined
Did you check that the bead was seated fully. inside and outside
Chris Potts yeah it turns out it was just the parking brake was partially engaged for whatever reason
I wonder can you disconnect the same switch on the latest model yfz
hmm not sure. Google it let me know
Im planing to put a 14 sprocket on my 2017 crf250r will that help my top speed without loosing a lot of my torque
Depends what stock is.
Thats the clutch safety switch. Basically you are tricking the quad into thinking the clutch isnt pulled in.
You got to do it the same day
Did you ever find out what was causing the back tire to wobble?
yes turns out the rear parking brake was partially engaged. Simple adjustment fixed it.
Hey I have a 2017 Raptor 700R and i did a few mods and got mine running 90mph without disabling the rev limiter. I changed my sprockets front 15T rear 36T. I am running HMF Blackout Exhaust with the HMF Optimizer. For more stability I bought the Tusk wheel hub extension not the adaptor that goes over the factory stubs. Also I installed the GYTR air filter and left the air box cover on. I guarantee a quick fast response after these mods. Let me know what you think after you try it.
Marvis Smith I've since updated this bike to a HMF full system FCI intake and a PC 5 programmer. I do 82
Have you removed your baffles in your exhaust if not take a flash light look on your pipe you will see a super restricted baffle there are two inside your exhaust you can remove them with a 2 1/2 lb hammer and a long standard screw driver i did this to mine 16' then put a monster tip on it i recommend getting a fuel controller if you do this though to richen it up a little
Just seen this yes I have big 3 now, old video.
magnesium wheel cleaner works great, just wear gloves or make sure you dont have any open cuts
We have same gloves! I got a 2014 700r but it's defenetly not stock lol Im actually running 100 mph with my garmin GPS
Raptor700r Maniac subbed
Video?
hey raptor man, do you feel like your front end is extremely stiff? just curious, my 2015 700r feels very stiff and I'm 3 clicks up from the lightest possible setting and I'm 220 lbs just curious what you think? I know they went with a heavier spring for 2015 and 16, my last qaud was a 2005 troy Lee predator and I feel like the front end was alot smoother when it came to choppy stuff.
you know I'm really not sure. I haven't adjusted the springs at all yet, (I'm 270) but I prolly should. As far as the front end bro this is my first raptor so really idk. I do know I need to stiffin up the back to hold my fat ass tho lol when I get on it bitch turns to a low rider lol
82 is cookin pretty good on offroad rubber! Kinda wonder how fast my 2008 will do now with the full HMF exhaust intake and programmer.
should be faster than mine then haha
+RaptorMan2016 I have a yfz so mine only hits 72. Stock sprockets but I got a vortex ecu and full exhaust with intake mod. But nice raptor man. I had a 700r before my yfz and I hit 78 at the most
sprockets and gearing aside...taller back tires will increase you overall top speed assuming your have enough ponies to turn them. Just like throwing smaller tires on there decreases your gearing slightly... so theoretically with 22s on there you can do higher top speed than with 18s or 20s bolted on in the rear but it might take the quad longer to get to top speed with the heavier 22s.
+WarWizard Productions that's awesome. I've been working so much I haven't uploaded. I have a trip planned for September 15-18th so expect some real good videos coming soon.
same here haha
How can i do the rev limiter where is the location
as ive now learned, it doesnt do anything lol
I hit 79mph I'm 6'1-280 on my 2017 Raptor 700r SE all stock. Does ur fan make a buzz noise when it cranks on to cool of the engine? mines sometimes makes it and sometimes it quiet
mine sounds like a quik whistle
RaptorMan preciate it u got a bad ass quad looking to put some new tires like yours for better grip.
tires helped alot!
the msd is the ticket, custom fuel and timing. ohhhhh yeahhhhhhhhh
i didnt go msd but i like the pc5 so far
My fan kicks on quite a bit on mine, it's a 17' just got it about a month ago, is this normal? Every other person I know who owns one it rarely comes on. Idk
Martin Marentes yea it's normal. Where are u located? Outside temperature has a lot to do with it as well
Martin Marentes I would recommend Engine Ice as coolant for your rappy. Keeps in about 10 to 15 degrees cooler than normal antifreeze
What size gloves are you?
2XL
Sounds like the beads are not seated onto the rims . I had some tires on my 4x4 I had to lube and air up to about 60 psi to get them to seat. I also have a 06 raptor 700 with a 4in extended swing arm . It was 1 of the first ones that had a problem with the fuel pump,it would run rich and flood. They told me I was riding it too slow, meanwhile no one could keep up.lol. I ended up taking the restricker out of the muffler ,had not had any problems since. Its been the best bike I have had.
when I first got the tires back the guy said the had 6psi in each, come to find out there was really 20+psi lol I will give that a try as well. they are great bikes, love mine. thx for the info
are you running a fuel/ignition controller? I heard if you remove the baffle it will run lean?
no I think the defective fuel pump makes it really rich . So when I removed that baffle it was like I put a controller on it and a pipe. I almost sold it because I was pulling wheelies in 5th gear not trying. after I put the swing arm on it was a totally different bike. Only problem it was harder to turn. Im not a bike tech but im a ase master tech for automotive repair.
+steve schmittou what brand swing arm and how much, was wanting to extend it as well.
I think it was vdub racing I got a 4 inch but if I did it again I would do a 2 inch . Got it off of ebay
How is wheelies w the 15t
Still easy, 3rd is best for it.
how many tooth is the stock sprockets
Lunik Gjata 14
brembo needs to make brake calipers & disc for theese
Yozue Hatma be sick
Yeah it would it would problably stop in an instant
@@yozuehatma855 that wouldn’t be good u would probably flip
Did u upgrade case saver? And if so what did u get bcuz I want the 15t sproket as well
ruclips.net/video/5PzJVw8bcQA/видео.html
Nice bro. Im going for the raptor 350 im new to a quad so its the best choice i think hahah
Did the brillow pad work? Did you use solution with it?
it barely worked. just gonna paint it or powdercoat it.
@@RaptorWRLD That sucks. The conversation on my 2018 Raptor is doing the same thing. There's gotta be something out there that will clean it rather than having to powder coat it.
** the cover
I hit 87mph stock gearing and big 3 mod .200lbs rider. Also I use engine ice in my 2015 700 I have a vapor trail tech and my temps stay a average 10deg cooler then with regular coolant.
that's awesome! do u think I should go dual exhaust with the new single exhaust port system? or should I just go single exhaust setup?
+RaptorMan2016 from what I've read a single exhaust works better on the single port heads. I have gytr intake w/Ehs lid, Ehs racing programmer , fmf power bomb header and fmf power core exhaust and the power gain is extremely noticeable pulls like a freight train.
Raptors are great for on road there alot cheaper than running a car easier to maintain i guess once ur used to the gears n clutch there easy
very easy
Also, pulling the airbox lid off is creating a lean condition which is why you are running hotter than usual. I would recommend just leaving it on or putting a fuel controller on it so you don't damage your piston.
ok will do thx for the input
I would hate to see something let go in your motor from something so simple. When you order your exhaust (if you order one) just order a big 3 kit from tqsatv, he will map the pc3 or pcv for your quad.
+1 did PCV and FMF slip-on this weekend on my 2016. runs way cooler and tons more power. don't jack around with anything man, do PCV first. just plugging it and flashing it in makes a huge difference.
Maybe your bearings could be going or are gone when your stoped. Try wobbling the tire back and fourth if it moves then your bearing could be gone.
nah I tried that. my buddy said there is an adjustment and the axle he did the same thing and he said they are shims inside the carrier that I can adjust
Will the rev limiter work on a 2019 raptor?
no. didnt work on mine either.
RaptorMan oh ok thanks men do not worth doing it right
Marco ardaya just get the pc5 with timing control
Nice
thx brother ;)
09 780kit stroker crank stage 3 cam factory 4 exhaust
Take the cam chain cover and have it painted with high temp paint or powder coated... two bolts. Put your airbox back on that is horrible for your stock head. Let me know if u wanna see my quad
Craig Dacheff watch this instead... ruclips.net/video/5PzJVw8bcQA/видео.html
Craig Dacheff yes I would like to see your raptor 🤘🔥
Not bad 82 MPH, and to clean it use Purple Power and a a Tooth Brush. No joke. New tires will be like that at first. Mine was HORRIBLE it was almost not Controllable at all when I first put on my back tires. It's all of those little "Fingers" the molds on the tires once those wear off it will be good, is it almost as if you're riding on Slime?
Your comments always give me new hope lol thx for that. Will give that purple stuff a try. Stay safe brother.
RaptorMan2016 lol Glad to hear man! And good yeah Purple Power is amazing.
take a plastic 99 cent store brush like for doing dishes, chop the end off and stick it on an electric drill. works great for cleaning those tight areas. Dawn dish soap mixed really heavy with warm water is the only thing I use on my quads. I have used the purple stuff too works great but it will melt your hands if you get it on you lol.
TrailBlogger I have use Dawn as well ;) Works good for de greasing that's for sure.
+TrailBlogger lol ok sounds good thx for the input
I've heard Purple Power works for cleaning engines
ok will check it out
Yes, Purple Power is amazing it will clean it so good it will look Brand new again.
Hey has anyone had a problem with their parking brake loosing tension on the 2k16 models like me?
like the actual level on the handlebars? mine is still good
+RaptorMan2016
the tension on the brake itself, mines no longer holds, anyone know how to tighten that back up?
91 Octain they have an youtube video on here i fix mine
What brand 15t ur using?
Renthal
@@RaptorWRLD thanks so much
Try getting your wheel balanced. My friend has had it done. Had the same problem as you
nobody balances wheels
***** I've called all my local shops, no one around here does it including the yamaha dealers
IMO I would not hold High RPMs for sustained periods. Some Raptors owners are having issues with the crank breaking or wrist pins breaking.
yep im aware, im subscribed to Cuervo
The comment was mostly directed to people getting into this. Seems like it's the new owners that have engine issues.
Thanks for the efforts behind the content.
@@joshbrown1381 i guess im a new owner in a sense lol only been riding the 700 three years. if my bike breaks thats on me, i ride this thing too hard not to. i know who to call when that happens.
@@joshbrown1381 i wish i could film more, but life gets in the way unfortunately. the powers that be keep me away from what i love. hopefully i will get you some more content soon.
I'm a pre new owner. Lol.
Disregard if I sound like an expert.
I know vehicle brakes, driveline and transmissions. I am learning about bikes and quads currently.
I'm finding in life you need to make the time for yourself. If you let it, life/society will drain you of all your time.
Be careful running with no air box lid without a programmer. The full injection can't keep up with that amount of air increase. That may also be why it was heating up, its leaned out to much. i did this to my 08 and it didn't like it. i put a k&n on and put the cover back on until i do my exhaust and programmer.
2009reezen thanks for the heads up but this video is old and now have the power programmer FCI intake and full HMF Exhaust
Stock is 14t right?
yes
Mothers metal polish will fix that cam cover up to a mirror finish
My brothers bike was doing the tire thing too dropped it off at the shop today
let me know what they say plz
+RaptorMan2016 the bearings are going out
+Thelegitrager what year is it?
is u going to take the baferler out
nah, just gonna wait till I get my pcv
if I take it out now it will be running too lean
true but its cheaper and if u do it right it would be faster
YOUR BIKE IS TOO CLEAN, does it see mud?
Rarely! No thx keep the mud lol
This video is so old , but she still is clean 🧼👍🏼
mine hits 84
Try nitro Grit results are guaranteed
I have the same gas cap😂😂
Brock Smith noice!
you have to use purple cleaner it works great
tried. it didnt work.
Did u get anything to clean it with?
Nothing has worked, just going go buy clear cam cover from monster eventually.
Is there anything I can put on to keep it looking new?
@@timellis3336 plastics yes. ruclips.net/video/_Kg0rxR6rJA/видео.html
Okie ic
get a full exhast system to will add some hp and should gain speed
saving up for that now. thx for commenting
no worries my dads got the 2006 700 with the full DMC afterburner exhast system probably one of the loudest and meanest sounding pipes ive ever heard ahah
Ever tried 13/38??
no I prefer higher top speeds.
That's what I run on my LTR450.
Bro unplugging the cable is not enough - You have to jump or solder the connections together. It will let the ECU think it is always in Neutral disabling the 5th Gear limiter. Removing the plug is the same.
Pretty sure my 5th gear limiter is gone now
I searched all over on the subject. You have to connect the wires together as if youre pressing youre clutch lever continously. The ECU will think its in neutral and disable 5th gear limiter. 85mph is stock speed. Tuned Raptors go faster without limiter.
Well iam a fat ass lol I'm 260 lbs so 82mph sounds about right
go night riding and you will see ur exhaust get super red
I put the air box lid back on but I'm sure you're right if I woulda kept it off and rolled her that night it would have glowed red.
the tire might have debris in
nah it was clean
What My trx450r hits 87 and my raptor hits 89 but my trx takes off faster and is better to trough around but I still love the raptor
whats all done to it?
- First of all, what's you name bro?
- You really wanna get your quad going faster than 82mph? I think it's quite enough for off-road quad (it's not street legal) and crashing at that speed is not that fun (especially with wobbles wheel) :P
- It's not dangerous to disable the rev limiter? you can more easily kill your engine, no?
- I think I had the same issue that you have with your rear disc brake and I had to replace it with a new one. upload a video of it, it's interesting to see what is all about.
- Riding 82mph with shorts and not protection gear?!?! you are a lunatic bro! haha.
- I like your quad (;
***** I didn't get from you if it's risky or not for the engine (:
And sorry for my lack of knowledge, but what is big 3?
***** fuel box = Commander 5 for example?
***** tnx for the explanation bro!(:
My name is RaptorMan or you can call me Josh xD Disabling the Rev limiter will cause damage to the valves easier yes, but I don't care lol yes eventually I plan on putting a turbo on this bike so 82mph for me is not good enough. My old 1998 Banshee did 88mph so I would like to see this quad go faster than that. The brake issue sucks really weird.
+RaptorMan2016 Ohh...
ok RaptorMan lol :P
So I can confirm - you're a lunatic haha...
Alright
Huh I put 22 inch rear tires and 23 inch front tires on , K an N air filter, rejetted both carbs, Bills pipe, FMF muffler, 16t front sprocket , 37t rear sprocket, on a 2002 ,and it would run 100 mph and not overheat
negative ghost rider.
One more thing...my ran hotter with the air box lid off. It's too lean and not good for the engine.
rhino250r what did you do to get it more rich ?
Joshua Ruiz custom fuel map
Ok cool thanks 🤙🏼🤙🏼
Use purple power to clean it
tried it, didnt really work too good. used a brillow pad instead.
Mind you - Be aware that your Raptor will always start even on Gear - Unless you turn the kill switch to OFF.
it's always started in gear.
What I meant is without pressing the clutch lever.
Oh that's not a big deal really.
hey man whats up i have the same raptor it has an full akrapovic exhaust and it it limits at 105 km/h and the gears are to short do you have any social.mefia than we can talk thank you
twitter.com/Raptor_Man2016
RaptorMan dont you have facebook instagram or snapchat ?
nah
viber ?
???
Video monster power tip raptor 700
i have all my upgrades on my channel. i have the big 3 installed.
Oh sorry i must be watching an older video you have a stock pipe in the one i watched ya that blue hmf looks sick
yea check my other videos its all on here bro.
i tweeted you llok at twitter
l have a 2006 raptor 700r I run blue Ice's blue in Color
just bought that too
my raptor do the same thing its because you ran over something u wont supose to
meaning what exactly? like my axel is messed up?
yea
can u give me a shout out
Preacher washer
got one, didnt help
82 mph on pavement in shorts and tee shirt ??!!!!!!????
Yes of course.
+RaptorMan2016 hahaha
awe man try this for a smokin' hot machine. drain all the fluids outta your quad it'll be sooo much lighter you'll def hit 90mph. also replace all your wires with the smallest gauge possible to make your computer go into high horsepower mode and your sparkplug will fire hotter.
I always clean my bike engines with a product called "gunk"
yea I will check that out. appreciate it bro. I bought purple power and it did nothing. thx for the comment!
If you want more speed less wobble change the tyres to road tyres. I recommend Kenda speedracer. Go for larger back tyres. Bigger fronts too. It will be more of a road quad then. The quad wont corner as well but thats the price you pay. Put your air box lid back on and take your baffle out. At stock I was getting 88mph I'm 20stone. Alternatively go twin pipes power commander new air filter. You should hit over 100mph easy but it will sap your fuel adding these extras.
sorry i didnt see this sooner lol check my updated vids on the mods i installed if u havent already