How to Adjust & Tune Up a Bench Table Saw
HTML-код
- Опубликовано: 27 янв 2022
- I've made this new video to show you how to adjust a table saw in order to make precise cuts. These kinds of bench table saws are hard to adjust. This is due to the way they're constructed. For example, the worktable is never completely straight, like in stationary saws with a rectified cast iron table. The brushed motor in these bench table saws makes more noise and vibrations.
All of this, along with other factors, makes it impossible to do fine-tuning, which can be done with other kinds of stationary saws. Therefore, keeping this in minds, we should aim to adjust them as much as possible within their possibilities.
Plans for this project: bit.ly/3iRfbd9
All Mobile Workbench Videos: bit.ly/3C3gqhV
Blog Article: bit.ly/3G4oYX1
Where to obtain materials and tools that I use:
Multi-Function Workbench Plans: bit.ly/39eKtrr
Band Saw Plans: bit.ly/2JisRjf
Workbench Accessories: bit.ly/2OSNcKu
Follow:
/ paosonwoodwork
/ paoson_woodworking
/ paoson_woodworking
#woodworking #tablesaw #tuneup #adjust 
Хобби
All Mobile Workbench Videos: bit.ly/3C3gqhV
😊👍👍👍
When checking the blade against the mitre slot, the same tooth on the blade should be used. Set zero on the guage with the tooth toward the front of the saw. Rotate the blade toward the back of the saw and check the guage against the same tooth. by doing it this way, you eliminate any variables of the blade not being perfectly flat, etc. Love your videos!
Yep, that's how it should be done!
I was about to mention the same thing.
you're right Peter, thanks for the advice
Checking should be done again after tightening of screw because it’s impacting the setting
Thank you for explanation
I wish that every tablesaw has this options.
With kind regards G Noorderling - Holland
Thank you for these rarer techniques!
Thanks. I just bought the same table saw and need to ensure it is properly calibrated.
Thanks a lot for your vidéos. I buy a plan for your workbench because a change my table saw (bosch) for a Dewalt.
Bonne continuation !
1) Use the same tooth for measurement when calibrating the sawblade. The sawblade can be tilted in itself
2) use the same miter slot for aligning the fence as you have used for aligning the blade. You want the fence parallel to the sawblade, not to the slot and you can't guarantee that the two miter slots are 100 % parallel to each other
3) In general you have to adjust the zero point on the gauge for each position of the fence. Since you can move the second position of the fence relative to the first position the gauge need not to be at the position what it says. To clarify: you calibrate the zero point of position 1, it shows zero and for the distance of position two the gauge says 10. Now you move position 2 of the fence for calibration by 1. The gauge will still show a distance of 10 but in reality it is 9 or 11.
Hiii friend 😊👍👍
Thank you. This is the best video I've seen so far.
What a well built woodworking station! I'd buy one. Your craftsmanship & design esthetics is perfection
thanks!
Wow great video , I have the same saw so now I feel more confident tuning it up
Thank you Paoson for this video. I finally bought a good quality caliper and dial indicator. Up until I received these new measurement aids I used a square. Now I know how to set my Dewalt 745 table saw-properly!
thanks!
Desde España, ¡gracias por compartir esta guía para callibrar la sierra de banco!
Aunque no es el caso, no temas que tus indicaciones sean muy básicas, pues siempre son importantes; aunque algunos las conozcan, a otros nos servirán.
¡Internet es una hermosa herramienta!
Thx, nice guide as always!
Bel video, sicuramente un video che servirà a molte persone. Grazie
Grazie
*Great Video Really Helpful!!! I bought the same Model recently and I'm going to check and align it*
*And I have some other issues that I don't know how to solve but I'm trying*
*Thanks for the Video!* 🌟👍🏻
😊👍👍
Nice!
When you measure the distance between the slot and the blade, its better to use the same tooth of the blade at both measurements. So you can avoid the wrong results because of the imperfections in the blade...
But its woodworking. A half mm is a good resolution...
you're right, thanks for the advice!
Good insights. Thanks for share.
فوق الممتاز نشكرك على المجهود
Great video as always... Another way to perform calibration/alignments of saw blade is to buy calibration disk/sander plate... Instead, used cutting blade; you use a calibrated plate that you can also spin by hand to make sure your motor shaft is true as well . They run for about $30-50 usd.
Your way is still very reliable. You just have to watch for the blade condition that you will use.
Yesss sir 😊👍👍
Thanks for sharing.
Thanks for sharing that was great content
Thank you!
Thank you...
Thanks!
Great video! I have this exact table saw, I better go check and see how bad mine is.
thanks mate!
Thanks
You checked the blade is parallel on different teeth, should it not be the same tooth moved from front to back?
you're right, I'll check it again that way
Great vlog , what make is your table saw . Looks very nice unit .
Otimo projeto. Gostaria de saber quais são os modelos das guias de alumínio usadas .
Hi Paoson, how can I adjust the perpendicularity of the fence respect to the bench? Thanks
Fantastic setup. Good video. But i got one question. Do not want the fence to be exactly parallel to the blade? We were told in the maschine course this can lead to kickback. The recomendation is that the fence is some what more open in the end than before the blade. Depending on size of the maschine it is just a notch.
The machine is excellent, but I think that when setting up it is always necessary to start from one base. I understand that the slots on the table are made at the factory, but. It was necessary from groove to disk from groove to time, with the same size. Then from the second time to upar. And it will be more correct from the first time to the stop. The errors are summed up.
Any links on the guage you used?
Excellent video! tks, just one question, I have a dewalt table and I would like to adjust the sqareness of the fence against the work table becouse is not perfect .... Did you check this ? tks
@@royarisse good advise. I'll try tks
Great video. Did you check the 90° between the fence and the table. Mine was off quite a bit.
I forgot to show how to do that!
@@Paoson_Woodworking really interested about that too
Hey! love the video as always :) I have the same table saw and while i have aligned it as best as I can, doing so is made more difficult because the table top is slightly convex. Fortunately it is most flat near the blade but particularly at the four corners mine slopes down by a few mm. Have you found this with your saw? Have you found a solution or a work around while aligning? I typically align the blade’s 90 by zeroing my digital level quite close to the blade (on the table top right beside the insert)
Again thanks for the great video, love the workbench!
hi Edward. You're right, all of these bench saws have that problem. There is no simple solution, I do it the same way as you!
Tq😊
Good👍🏻
Good job! Your workbench with built-in table saw and router table is insane! I have been inspired by it and modeled a similar design myself in a slimmed down form with the DWE 7492.
Thanks for all the good suggestions and your advice on calibrating the table saw. One question remains, however: How do I set the rip fence square to the saw table? On my saw, it is below 90° and I can't find a way to correct that without voiding the warranty. Do you have any advice for me? Many greetings, Phillip
hi Phillip, I don't think it can be adjusted, sorry!
when you align the blade to the miterslot you should also give the screws a fresh drop of threadlock. if you check your alignment again now you will notice that it did move away from your earlier messurements. i did not believe it untill i just re checked my blade alignment. now that i secured them back in place i messured again and this time the blade stays right in place
I really enjoy watching your videos, this is the best workbench I ever saw. I have just one question, what table saw do you have, is it DeWalt 7492?
yes, Dewalt 7492 qs
Still waiting on the new fence 😘
Se o audio fosse em português do Brasil seria otimo, seus videos São top.
Good
Hi
Can't use the built-in rulet to measure less than 20 cm ?
Una pena que en castellano no allá subtítulos como antes .eres muy bueno y sería agradable saber lo que dices
lo puedes leer aquí Luis: www.paoson.com/blog/es/como-ajustar-o-calibrar-una-sierra-de-mesa-o-de-banco/
@@Paoson_Woodworking gracias ...
what kind of caliper did you use? I know the support is home made but I find the dial very readable and easy to use
www.paoson.com/forum/viewtopic.php?f=22&t=1940#p11208
Hola suso, en dónde se puede comprar el gauge caliper? O lo tienes como uno de tus magníficos proyectos??
hola Juan, busca en google por "indicador dial sierra mesa"
is your tablesaw flat? Mine is a little bit lower in the middle. That can affect the setup process. For example fence is off square a little the further I go. I heard a lot of people have the same issue with their Dewalts.
mine too....
I cannot recognize the gray material you use for many processes.
maybe i missed his name. could you tell me? thank you very much.😃
Why did you select Dewalt?
What specific type of dewalt saw are you using?
www.paoson.com/forum/viewtopic.php?f=22&t=1940
Thank you for the information!
it has been very frustrating for me to adjust the blade on my dewalt table saw, it is still off after many tries.
they are not the most accurate saws...
Still going to do a fence for the saw/bench?
yes, I hope to have it in a few months
May i ask what is the model number of your table saw?
www.paoson.com/forum/viewtopic.php?f=22&t=1940
Puedes subtitular en español? Y ya me entero del todo jejej
lo siento Juan, en este artículo encontrarás todo lo que explico en el vídeo: www.paoson.com/blog/es/como-ajustar-o-calibrar-una-sierra-de-mesa-o-de-banco/
@@Paoson_Woodworking vale gracias, es que tus videos son buenisimos pero en ingles unas cosas las pillo y otras no jajaja pero eres una maquina 🙌🙌🙌
Competent adjustment
When you want to check a blade for true 90 degrees always use a true set square NEVER a combination square
Have you ever had to adjust your riving knife to make sure it's perfectly in line with the blade?
yes, I had to use tape on its left side to move a little to the right
@@Paoson_Woodworking any chance you can do a video on it? Or a video chat to show me e.g., Skype, Google Meetings, etc. This seems to be a big issue for a lot of people and there isn't any good information on RUclips or the internet to help address this.
The slots on this table saw (dewalt 745) are not too accurate. Some places, the slot is tight and other places, it is loose. Its because of the coat of paint on the aluminum surface. Take care of that first. Thats my experience anyway.
yes, I already checked
first ;)