I have a question . Why after I enter values in the EM-100 controller after pressing the record button, after switching off and on again the controller returns to the old settings.
@@derbestebusfahrer. How did you get it working? I have the same problem.. tried 2 different EM software versions. What version worked for you? thanks!
OMW.....So after work today, I played with my settings. In the never ending quest to find settings that will make my ebike mimick the feel of a CR 125. Welp, I was on page 3 and decided to enable moving vehicle booster. I tried the stock #10 setting and not much. I then set it to 30. That's all I did, and wrote it. It flies. Moving vehicle booster Speed ratio is all I touched so far. it's got to be the secret setting no ones talking about.
Hope my question wis reasonable. Is it absolutely necessary to have the controller hooked up to the computer diagnonis? I got to having it hooked up and finally connecting the learning wires and turning the key to on. No motor turn. My display turns on, but I think it runs from my head light wiring. I haven't tried to turn the throttle yet, but I want to. USB wont be here till tomorrow, it says.
I keep getting a hall fault on my em150sp, the dkd display powers on and starts on mode 3 and it can do sport + reverse but not 2 or 1. As well the motor has still yet to turn, do I need to do the self learning process for the hall or do I need to rewire/reprogram something?
Yes, @8:20 (page 2), if you check HDC enable and specify an RPM limit (6000 rpm in this case), then in the Three-speed section, he has 80%, which is 80% of 6000 rpm), for LOW, which is 4800 rpm. For you to set LOW to give 25 kph max, you just adjust the % of LOW until it limits your speed, which depends on motor type and tire diameter. Probably by now you already found someone who helped you set this basic setting.
Would you be willing to help me correctly figure out what pin-out is correct for my Votol Em70 PLEASE? or ANY help in locating the correct data plug!? I have seen "modification groups" and after reaching out, received no response what so ever. I understand time is a rare commodity, and would be willing to compensate... Thank you. PS: I understand this SHOULD be a EASILY answered question. Evidentially Nobody has spent time programming the EM-70 BLDC controller. Ours is specifically re-badged as a "YMMOTORS" variant, and to my attention has a COMPLETELY different pin-out compared to the schematic presented on the VOTOL web site, along with the prints shown in the sales links VIA Amazon. I am very nervous to simply cut into my harness without knowing the correct designations. Bike has been SPECTACULAR, EXCEPT we are limited to GEAR 2---45ish MPH!!! Gear 3, 4, and Sport remain without access. This may sound like a simple issue, and may be, but without correct english translations, and incorrect or limited knowledge, quickly becomes a chore. ANY HELP or DIRECTION would be dearly appreciated, as you seem to be able to navigate electronics IE drones/bike. very well. Keep up the hard work, and thank you for sharing your finding thus far!!!
@@AdventureBrad understandable. Unfortunately it was purchased through @flyebikes and did not have a admirable "after purchase" experience, not that I expected much. Been trying all outlets we can find that may have the time or knowledge to assist in this endeavor. Thank you for a quick response, and we still love your detailed content!
HI. Thank You for this tutorial. So, i have problem with my EM_150/180A. Any way to connect with software. I thik that firmware is corrupted. Could You send me Your on priv, please?
any tips why mine wont connect? it keeps popping up with a error when i connect the controller and i have tried EVERYTHING , contacted the provider and they weren't much help tbh
I have a question .
Why after I enter values in the EM-100 controller after pressing the record button, after switching off and on again the controller returns to the old settings.
Same here, did you ever get it working some how?
@@TackleThat yes, Probelem is with Software.
@@derbestebusfahrer. How did you get it working? I have the same problem.. tried 2 different EM software versions. What version worked for you? thanks!
Hey, how do we map the port settings with the pin number/color in the connector. Don't understand what PD0,JTCK,SWD etc. mean
OMW.....So after work today, I played with my settings. In the never ending quest to find settings that will make my ebike
mimick the feel of a CR 125. Welp, I was on page 3 and decided to enable moving vehicle booster. I tried the stock #10 setting
and not much. I then set it to 30. That's all I did, and wrote it. It flies. Moving vehicle booster Speed ratio is all I touched so far.
it's got to be the secret setting no ones talking about.
Nice will have to check that out. Thanks for sharing
Hope my question wis reasonable. Is it absolutely necessary to have the controller hooked up to the computer diagnonis?
I got to having it hooked up and finally connecting the learning wires and turning the key to on. No motor turn.
My display turns on, but I think it runs from my head light wiring. I haven't tried to turn the throttle yet, but I want to.
USB wont be here till tomorrow, it says.
I keep getting a hall fault on my em150sp, the dkd display powers on and starts on mode 3 and it can do sport + reverse but not 2 or 1. As well the motor has still yet to turn, do I need to do the self learning process for the hall or do I need to rewire/reprogram something?
Is there a setting which can limit the top speed of ECO mode to 25 km/h?
Yes, @8:20 (page 2), if you check HDC enable and specify an RPM limit (6000 rpm in this case), then in the Three-speed section, he has 80%, which is 80% of 6000 rpm), for LOW, which is 4800 rpm.
For you to set LOW to give 25 kph max, you just adjust the % of LOW until it limits your speed, which depends on motor type and tire diameter.
Probably by now you already found someone who helped you set this basic setting.
Would you be willing to help me correctly figure out what pin-out is correct for my Votol Em70 PLEASE? or ANY help in locating the correct data plug!? I have seen "modification groups" and after reaching out, received no response what so ever. I understand time is a rare commodity, and would be willing to compensate... Thank you.
PS: I understand this SHOULD be a EASILY answered question. Evidentially Nobody has spent time programming the EM-70 BLDC controller. Ours is specifically re-badged as a "YMMOTORS" variant, and to my attention has a COMPLETELY different pin-out compared to the schematic presented on the VOTOL web site, along with the prints shown in the sales links VIA Amazon. I am very nervous to simply cut into my harness without knowing the correct designations. Bike has been SPECTACULAR, EXCEPT we are limited to GEAR 2---45ish MPH!!! Gear 3, 4, and Sport remain without access. This may sound like a simple issue, and may be, but without correct english translations, and incorrect or limited knowledge, quickly becomes a chore. ANY HELP or DIRECTION would be dearly appreciated, as you seem to be able to navigate electronics IE drones/bike. very well. Keep up the hard work, and thank you for sharing your finding thus far!!!
ask the seller you bought it from. I haven't played with a em70
@@AdventureBrad understandable. Unfortunately it was purchased through @flyebikes and did not have a admirable "after purchase" experience, not that I expected much. Been trying all outlets we can find that may have the time or knowledge to assist in this endeavor. Thank you for a quick response, and we still love your detailed content!
HI. Thank You for this tutorial. So, i have problem with my EM_150/180A. Any way to connect with software. I thik that firmware is corrupted. Could You send me Your on priv, please?
any tips why mine wont connect? it keeps popping up with a error when i connect the controller and i have tried EVERYTHING , contacted the provider and they weren't much help tbh
what is the error? can you see the controller in the serial port?
more then likely its a driver problem. might try a different computer too
@@AdventureBrad i can see my port , its communication abnormal that is the error i cant seem to shake
Hello sir plz tell me the difference between em150 and em150sp controller
Sir how to do reverse setting
Not sure
Great
Please explain how to measure Hall Shift Angle with oscilloscope, or at least point to some documentation, please. I can't find any.
Where is the auto-learn function?
Mine says when press connect … let’s open the serial port
that means your computer is not seeing the usb adapter. make sure the drivers are installed and updated and pick the right com port
@@AdventureBrad now that part i have to figure out the drivers I'm not to computer savy