Hi something similar is happening to my EM50SP it always bring 0 at overvoltage and phase current..... write is ok but comes with 0.... i think is bricked...., do you think that can be fixed with a similar procedure with proper em50 firmware? will debug mode exist for em50 software too? thanks in advance
Hola saludos de Uruguay compre una VOTOL ME30S para practicar la programación no me funciona el motor y tengo un código 00000280 no entiendo el manual de códigos
hi can any one help me?? i need some file of your settings im using votol em150 and mid drive motor 4000 watts when i push the throttle its clicking only motor wont spin
Try one of available in description firmware. You should luck. All action you will for your OWN RISK. :) In description firmware compatible (tested) with 150/2 200/2 260/2 try with 100/2
@@VOTOL_MAGIC my friends uploaded into em100 and then em100 can't communicate again to laptop, If bin file upload to em150 same thing happen such em100?
@@fzmetric Try any firmwares from this and your controller will up: --- disk.yandex.ru/d/lcV6N30ttnocbw disk.yandex.ru/d/TC5kSb2wRJjVTQ disk.yandex.ru/d/sA9qu_usFZGc6A disk.yandex.ru/d/a4ws0R2I783XZA Instructions for upload: Just open port of controller and upload firmware WITHOUT CONNECT --- Give me your feedback.
I am actually trying to read the Regen data from VOTOL EM 100 via the RX TX pin , Do you have any suggestions
absoulute ledgend
How do you extract and save a copy of a firmware? I want to save a copy of the firmware m em50s uses
Hi something similar is happening to my EM50SP it always bring 0 at overvoltage and phase current..... write is ok but comes with 0.... i think is bricked...., do you think that can be fixed with a similar procedure with proper em50 firmware? will debug mode exist for em50 software too? thanks in advance
Yes. It's possible way to rewrite settings but in another way.
tks you so much
Hola saludos de Uruguay compre una VOTOL ME30S para practicar la programación no me funciona el motor y tengo un código 00000280 no entiendo el manual de códigos
by the way, do you have link of votol software that you use?
disk.yandex.ru/d/p7vsRKkgWqXiyg
@@VOTOL_MAGIC thanks you very much..
hi can any one help me?? i need some file of your settings im using votol em150 and mid drive motor 4000 watts when i push the throttle its clicking only motor wont spin
Hello there new to all of this, i have a em70 controller , bin files where would i find them?
They are in the description.. did you try them? Not sure if I should test this on the em100.
Do you have latest bin file for CAN based EM100
Try one of available in description firmware. You should luck.
All action you will for your OWN RISK. :)
In description firmware compatible (tested) with 150/2 200/2 260/2
try with 100/2
Did it work on the EM100?
necesito un firmware para mi votol EM 100S ver 1.5 microprocesador stm 32
necesito actualizar a la sw 2.33
This firmware could use in em150 can bus?
/2 you can.
@@VOTOL_MAGIC my friends uploaded into em100 and then em100 can't communicate again to laptop,
If bin file upload to em150 same thing happen such em100?
@@fzmetric because EM100 doesn't support CAN Bus, i will try to help your. I'm uploading now few firmwares for your. Wait .
@@fzmetric
Try any firmwares from this and your controller will up:
---
disk.yandex.ru/d/lcV6N30ttnocbw
disk.yandex.ru/d/TC5kSb2wRJjVTQ
disk.yandex.ru/d/sA9qu_usFZGc6A
disk.yandex.ru/d/a4ws0R2I783XZA
Instructions for upload:
Just open port of controller and upload firmware WITHOUT CONNECT
---
Give me your feedback.
@@VOTOL_MAGIC em100 my friends is can bus..
Здравствуйте, есть ли у вас прошивка на em200/2?
В комментарии ссылка она совместима.
Он прошивается, но всё остаётся в настройках как и было, и ограничения оборотов до 2200 об/м
По моей инструкции следовали?@@goshka2386
Do you have firmware em150 can bus? Please..
CAN BUS is 150/2 ? or... ?
@@VOTOL_MAGIC how i can identify series em150?
@@fzmetric factory USB dongle has 2 contact or 3 ?