Hello. I’m a little confused, after you added the inside framing to the legs what did you do at the arch. The video goes fast and it’s not mentioned in the voice over.
Hi, thanks for watching. Sorry I do have to speed these up faster than I would like. This build took probably like 3 hours in total. And any time I have a video over 15 minutes they don't do well. So I have been trying to keep my videos shorter. This video was mainly focusing on cutting straight lines and tracing a arch with out a stencil. As those are the two questions I receive the most by far. Especially since my channel is more toward the beginner maker. But the arch was even easier than the framing for the legs. I made sure to put all the information needed in the plans along with images to simplify the build. I believe it is only 9 steps to complete this arch. I also have a longer video that is available with the plans that shows this whole build, so there is no confusion. The plans for this build is linked above under the video. And the full, I think 17 minute video is on my youtube channel for members. I completely understand if your are just looking for a video showing how. I have a video here that shows how I built a similar version that may help. But that video build was more difficult than it had to be. That's why I created the plans for this one. Here is that video ruclips.net/video/QuhTFBu43As/видео.html Again as the video above was more for focusing on making straight cuts and creating the arch, I hope that helps. Thank you very much for commenting and good luck!
Hi, for this build a drill, circular saw, jigsaw did the trick. But I also used a brad nail gun, it shoots small sized nails and is easy to use. It is not necessary as it can be made with out brad nails and using different size screws. But it makes it so much easier and will probably be much quicker. And looks nicer with out all the screws showing, Good luck!
Hi, I just finished the plans and uploaded them. Here is the link. Thank you for the support! makerdecorshop.com/products/3d-single-arch-plans-with-measurements
Hello. I’m a little confused, after you added the inside framing to the legs what did you do at the arch. The video goes fast and it’s not mentioned in the voice over.
Hi, thanks for watching. Sorry I do have to speed these up faster than I would like. This build took probably like 3 hours in total. And any time I have a video over 15 minutes they don't do well. So I have been trying to keep my videos shorter. This video was mainly focusing on cutting straight lines and tracing a arch with out a stencil. As those are the two questions I receive the most by far. Especially since my channel is more toward the beginner maker. But the arch was even easier than the framing for the legs. I made sure to put all the information needed in the plans along with images to simplify the build. I believe it is only 9 steps to complete this arch. I also have a longer video that is available with the plans that shows this whole build, so there is no confusion. The plans for this build is linked above under the video. And the full, I think 17 minute video is on my youtube channel for members. I completely understand if your are just looking for a video showing how. I have a video here that shows how I built a similar version that may help. But that video build was more difficult than it had to be. That's why I created the plans for this one. Here is that video ruclips.net/video/QuhTFBu43As/видео.html Again as the video above was more for focusing on making straight cuts and creating the arch, I hope that helps. Thank you very much for commenting and good luck!
Stunning! Can’t wait to try!
Thank you and good luck!
What would is that, the bendy one you used to wrap it
What basic power tools should I buy? Thanks
Hi, for this build a drill, circular saw, jigsaw did the trick. But I also used a brad nail gun, it shoots small sized nails and is easy to use. It is not necessary as it can be made with out brad nails and using different size screws. But it makes it so much easier and will probably be much quicker. And looks nicer with out all the screws showing, Good luck!
Dope one, very understandable
Thank you!
Hey!
I can't find the template for this?
Hi, I just finished the plans and uploaded them. Here is the link. Thank you for the support! makerdecorshop.com/products/3d-single-arch-plans-with-measurements
What are the measurements?