Это видео недоступно.
Сожалеем об этом.
Samsung Tab A 8.0 Charge Port Repair (SM-T350)
HTML-код
- Опубликовано: 24 янв 2019
- Start to finish Samsung Tab A 8.0 charge port repair. (SM-T350)
Equipment I use:
QUICK 861DW Hot Air Station: amzn.to/2stBhMG
Amscope SM-4TPZ Trinocular, Simulfocal: amzn.to/2t5m44u
Entry Level Scope: amzn.to/2Q1EFr2 what I started out with, I prefer the SM-4TPZ.
Amscope LED-144B-ZK: amzn.to/2MvTTTi
Hot Air Station: Quick 861DW:
Hakko FM203 Soldering Station: Hakko.com
FM2027 Standard Iron W/ Stand (FM2027-03) Conversion Kit: Hakko.com
T15-J02 (Main Tip I use) Hakko.com
T15-JS02: Hakko.com
T15-BC1: Hakko.com
T15-BC2: Hakko.com
T15-BC3: Hakko.com
FM2032 Micro pencil W/ Stand (FM2032-52) Conversion Kit: Hakko.com
T30-J Main Tip I use: Hakko.com
T30-I: Hakko.com
Kester 44 Rosin Core (.015) Leaded Solder: amzn.to/2t5nsUK
Desoldering Braid, Tech Spray no-clean #3 1822-5F: Newark.com
Flux Kingbo RMA-218: amzn.to/2t4xWDR
Tip Cleaner: amzn.to/361Bi9p
Soldering Mat: amzn.to/350bnO7
Soldering Mat: amzn.to/2seMzEN what I am currently using
Table Mat/Protector: amzn.to/34VNvet
SMD Practice Soldering Board: amzn.to/2Svra4W
Power Supply: amzn.to/2Q0Bu37
Webcam C525: amzn.to/360kQWF
Microphone: amzn.to/2PXrTdk
Multimeter: amzn.to/2EZSKPq
Anti Static Gloves: amzn.to/3505hNJ
Blue Solder Iron Rubber Sleeve: amzn.to/2PYaCki
Orange Solder Iron Rubber Sleeve: amzn.to/39cq6bP
Hakko CHP 3-SA Stainless Steel Tweezers: amzn.to/35YO88c
Red Tweezers: iPad Rehab.com
Micro Cutter: https: amzn.to/39foIW2
Underfill Removing Blades: amzn.to/351TGgO
BGA IC Chip Remover Tool (underfill): amzn.to/2tULAKg
Hakko 599B-02 Tip Cleaner w/ copper sponge: amzn.to/2Q0fbuk
USB Amp Meter: amzn.to/2EY13eG
Jumper Wire 0.0034: amzn.to/2t2HRtE
Jumper Wire 0.0069: amzn.to/2MwrFYu
Super Cold Spray: amzn.to/2MwrFYu
Compressed Air: amzn.to/2StpKaR or whatever is less expensive.
Alcohol Dispenser: amzn.to/2snKWo7
Alcohol Dispenser 2: amzn.to/2sn9o9b
CBP Heat Pad: amzn.to/2EUycYK
iSesamo: amzn.to/360QMdC
iFlex: amzn.to/2ZtxpYs
Magnetic Project Mat: amzn.to/38M286a
amzn.to/3fZWnXE
Social Media
Facebook: / techwarrior1
Instagram: www.instagram....
Twitter: / techwarrior308
Patreon: / tech_warrior
RUclips: / @techwarrior9115
DISCLAIMER: This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. I only endorse products that I have personally used. Thank You for your support!
If this video helped you in any way please subscribe, like or share it with a friend.
What tool kit did you use for this to open the tablet? Everyone i find online looks like junk, I didn't find it in the description...
@@analogaudiorules1724 The tool I used is an iSesamo, I have included it at the bottom of the description. Thank You for watching. Let me know how it goes.
Where to solder to add sim adaptor on this board. Is the pcb having pads to solder the sim socket
Nice video! Though It'd be nice if there was some kind of description or if you could describe the process. :)
JEYPix thank you for watching, this was a video of me trying a different angle, just uploaded it for those who need to see the process, I do all of my charge ports the same way. My next videos will be explained of the tools I am using and what and why I am doing it it.
i added a short video explaining my step by steps.
The video is very helpful. Thank you so much.
Oscar Duran thank you
I have a Tab from 2022. Not sure which one. Battery is dead so I can’t look at the system. The top bezel appears very thin. I have the usual tools but this doesn’t have a gap-just a thin line around the display. I guess it has to be heated first before removing the display. I think it was a 5?? Model.
usually the back has the model number. where did you buy it from? they might tell you the model number.
Is the charging icdor sm p205 on the main board or was it on the charging port board? Thanks
I always look for the model of n the board or the model number of the tablet, make sure to look at the pins and anchors of the charging port to make sure they line up when you see pictures of the ones you will order.
Hello Tech warrior. I was curious if this is what I should do if the tablet says it detects moisture on USB port?
Thank you for you help
Thank You for watching, has the tablet had any water damage? are you using the original charging cube and charging cable to charge the tablet?
Can I replace the port with one from a different device (bluetooth headphones)?
Only if it has the same pins and anchor points, Samsung does use the same ports on many devices but I would not force a similar one.
I need this done to mine. What kind of price should I expect to pay for this?
Prices may vary, I am at $75.00 plus tax.
What is the product that you are using with the syringe
Kingbo Flux, it comes in a jar style bottle.
Your charge port isnt the same as the replacement shown on amazon. They have an extended lead with plug end
Mark Kam thank you, I will have to take a look.
Hello Tech Warrior, you obviously know what you’re doing here. I have this exact tablet and recently replaced the digitizer screen; now sections of the screen are non responsive, like an inch around the outside perimeter, so the bottom row of the password screen doesn’t work. If you have any advice on this, I would greatly appreciate hearing it. Can it be that the digitizer is bad or did I damage something? If not the digitizer, what else might be the problem? Thank you.
3:10 on my video is where the touch connector is, make sure it is connected/seated properly. check touch again.
Tech Warrior Thanks, I’ve checked it once but I’ll do it again, maybe it’s not seated properly. Appreciate your response.
What resin were you putting on the circuit board pins? And what type of tweezers were you using? Thank you
Frances Dugas about what time are you referring to?
FLux
good job where are you located can i send my unit and you do it...how much you charge..thank,s
Thank you for reaching out, currently, I am not able to take in any services. Where are you located?
Hello Sir, I flashed something (I was trying to install Custom Rom) via odin on my SM-T350. Now my SM-T350 is hard bricked or you can tell it is dead. No boot animation, no download mode, no recovery mode nothing is appearing on the screen. So, I am pretty much sure my device is hard bricked. Is there anyway to recover it? Please tell me.
~Saad
Hello, was the tablet fully charged when you flashed it? try charging the tablet for 3 hours and see if it will turn on, disconnect the battery and press the power button 7 times and then try charging it for a few hours. If that doesn't work try hard resetting the tablet by pressing and holding the power button, up volume key, and the home button at the same time. use the volume to move up or down to select reset and use the power button to press enter. Let me know wich one worked.
when i insert charger it is carging 100% but i remove the charger it turned off,what can i do.Please say
Thank You for watching, how long have you had the tablet? if more than 2 years it may need a new one. If you can disconnect the battery press the power button 7 times, connect the battery and let charge for 15 minutes to see if it is doing the same thing.
when connect the charger hitting problem
can you see if the pins inside the charge port are bent? Most of the time the pins prevent the charge port to be inserted all the way.
Sir can you plz help me my phone is not turning on, the section above the charging port is getting heated up when I plug it to charge, I can share you the pics of the section which is getting heated up and I suspect one capacitor is burnt , so can u share ur mail id or whatsapp so that I can send pics
you can send the pictures to techwarrior308@gmail.com
It's a great video, but not real helpful. Explaining the process, what substances you use and whatnot would of been a great help. So I can see how to do it, but have no clue what stuff to use to do it right
Jj McKinney thank you for the input, I will make another video in English and explain the step by step, I have a video that explains the tools I use but it is in Spanish. I will make another tools video in the near future.
Jj McKinney I will make a new video soon with step by step and tools used. Thank you.
@@techwarrior9115 That's great, thank you for your response
Did you ever make the new video for this in English?
I was thinking, I bet you don't put comments in your code either, then saw others wanted descriptions too. Could you at least give us the link to your video in Spanish? Or at least add a list of materials used to the description header. (Where we click SHOW MORE) Thanks.
Deborah Freedman thank you for watching, this is the link to my tools video. I will start doing videos both in English and Spanish. ruclips.net/video/Eeqwhk1hwO0/видео.html
Sorry that you are a mute. Your video would have been good if you had a non mute person to explain what you are doing.
Not a mute, just didn’t have a good microphone. It’s easy to follow. Thank you for your kind words.