Fiat 500 Rear Brake Shoes Replacement, Remove Hub Or Not? same as ford ka
HTML-код
- Опубликовано: 15 окт 2024
- The Rear Wheel Kept Jamming, Not Rotating like the handbrake was jamming on, the issue was down to the rear brake shoes loosing their linings.
In this video I replace the brake shoes,
It can be done without removing the rear hub but it's difficult.
The easer way is to remove the hub. I show both options in the video.
Links to all tools used in the video www.amazon.co....
Link to rear brake shoes on amazon £19 amzn.to/2Z49AdZ
this is easily the best rear brake servicing video .. i am 78 yrs and have recently serviced a 2021 Fiat Panda Hybrid .. I love mechanicing on vehicles ..the rear wheels were not spinning freely at only 25,000 km from new . one hub was dragging and the other drum was catching slightly .ECONOMY?. with the shoes and hub removed I washed the backplate using brake cleaner .. Brushed a liberal coating of 3M cavity wax rust preventer all over ., Greased all of the brake shoe contact points and reassembled. taking care to copper grease everything which slid or moved . spraying some chain lube into the springs coils and the pivot on the handbrake shoe . The slightly rusty edge on the brake drum was removed using a pad made out of 150 grit emery paper .
Well done, Thanks for the great comments👍🏻👍🏻🛠
Fantastic…wife’s 500 rear brakes failed as the wheel cylinder sprung a leak and I was looking for the procedure to go about replacing it all ( including drums that are 13 years old)…found your vids and they are superb! Thanks so much for posting as it saves rummaging through 5 or 6 pages of a Haynes manual and invariably cocking it up. Top job buddy
Happy to help, Thanks for the great comments👍🏻👍🏻🛠
Cheers for the help. Actually doing work on mk2 Ka as same as the 500 and easier to find 500 videos. Sister's car failed mot as the hsndbrake was barely working on 1 side. My and my mate took it apart to have a look to see what was wrong and the shoe fell apart. The pivot point was stuck but needed new shoes. Got 1 done tonight. Will replace the other tomorrow
Well Done. Thanks for the great comments👍🏻👍🏻🛠
Just bought the wife a Fiat 500 and this will help me do the work myself
Thanks for the great information👍🏻👍🏻🛠
Useful video!! Thanks!
I have replaced rear brake shoes and drums and hand brake adjustement, but handbrake does noy brake very well. It brakes but nor 'braking bite' on a steep slope...
Any idea??
Have you given them a chance to bed in, the performance will improve after a few hundred miles, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 ok. I am to drive some miles more and let see...i understand that fiat 500 rear brakes (drums, no discs) have to be able to slam handbrake??
Thank you for some very informative how to videos for all 3 on the fiat 500 braking system.
And links to parts etc... spot on
Very clear and easy to follow.
Glad it helped, Thanks for the great comments👍🏻👍🏻🛠
Informative with no bull. Excellent, many thanks
So nice of you Thanks for the great comments👍🏻👍🏻🛠
Brilliant step by step guide made simple and easy to follow with great tips for ease of access
Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠
Excellent 3 vids on the brakes.. very similar system to many cars but nice added tips and tricks you have noted .. demistifies the voyage of discovery when working on different cars.. thanks and best wishes.
Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠
excellent demo- gonna do my daughters tomorrow now ! thank you
Have fun! Thanks for the great comments👍🏻👍🏻🛠
Great vid , hopefully help me replace rear brakes on my 500 . Any advice , if I may ask ? Can’t get rear drum off one side .
If I slacken handbrake cable off inside the vehicle , will this aid in removing the drum ?
Thanks in advance for any advice. Happy new year.
use the bolt holes on the drum like I show later in the video to wind it off, defiantly slacken the handbrake, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 thanks once again. Followed you’re advice and Yes the bolt holes worked a treat . Drum removed and shoes ordered.
I’ve obviously subscribed to your channel. Keep up the great content. 👍
Good tip with the wire cutter pliers..will it self adjust as I can’t seem to turn my adjuster wheel 🤔
If the wheel is not seized but it will take ages, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 the wheel is free but difficult to turn when in place..thanks for your help 👍🏻
Great info , ive opened up a KA 09 adjust the hand brake but found the adjuster is broken , the little clip that id click it on is detached and spinning , i see i can buy them separate does that mean i can do them without changing the whole back brake system ? Thanks
Yes sounds right, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 Thanks for the reply 🖒
Well done mate thanks for making the effort to make a very instructional vid, cheers!
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
hi, love the video.nearly the same as the Panda 2016 i think, i use a dab of white paint to mark where the springs go,. that car was in bad condition.i check my brakes every 2 years
It was poorly maintained, Thanks for the great comments👍🏻👍🏻🛠
Cracking job there were well ready for changing 👍
they were had it, but all good now, Thanks norm for the great comments👍🏻👍🏻🛠
Afternoon Ant.
Another fantastic video.
Always full of information & helpful tips.
Keep up the good work.
Stay lucky. Stay safe. Stay healthy.
Alan L200
And some Milwaukee tools😂 Thanks Alan for the great comments👍🏻👍🏻🛠
Great video,very informative, broken down in stages easy to understand,very helpful
Glad you enjoyed it! Thanks for the great comments👍🏻👍🏻🛠
Best video on the topic!
Thanks for the great comments👍🏻👍🏻🛠
Appreciate the effort to create this video thanks.
Thanks for the great comments👍🏻👍🏻🛠
Great video, what mileage had the 500 done ?
About 80000 Thanks for the great comments👍🏻👍🏻🛠 xx
I will try to check the brakes on our caravan tomorrow 🙂
Thanks for the great comments👍🏻👍🏻🛠
Your a brave man jacking a fiat up on the spring pan 😂
😂 Thanks for the great comments👍🏻👍🏻🛠
Hi there my name is Deno I am from South Africa and I drive a fiat Fiorino panel van, I am struggling to replace my handbrake cable that fits into the one part of the brake shoe, can you please help me
I show some of it in this video, Thanks for the great comments👍🏻👍🏻🛠
Very good explanation
Thanks for the great comments👍🏻👍🏻🛠
Amazing video, absolutely mega
Glad you enjoyed it! Thanks for the great comments👍🏻👍🏻🛠
Thanks very much!
You're welcome! Thanks for the great comments👍🏻👍🏻🛠
Great video 👍
Thanks for the great information👍🏻👍🏻🛠
Thanks for the explanation and a great job
You are welcome! Thanks Tahir for the great comments👍🏻👍🏻🛠
Sir ..do sit and work like that .. with your leg under the vehicle...
Safety Always comes first ...😊
Thanks for the great comments👍🏻👍🏻🛠
Brilliant, cheers mate
Thanks for the great comments👍🏻👍🏻🛠
Very useful guy
Glad you think so! Thanks for the great comments👍🏻👍🏻🛠
Great video - Thanks
Glad you enjoyed it, Thanks for the great comments👍🏻👍🏻🛠
thanks 😎 buddy great video on this cheers 🥂
Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11
just doing a 500 front brake s this week 😁 has spline drive type holding front carriers on will have a look at back one s to look s lots better to remove the hub thanks for the tips well appreciated
Its a screwdriver, not a chisel or a prybar ! it even says that on the handle😆
😂 Thanks for the great comments👍🏻👍🏻🛠
I hate drum brakes. Horrible nasty things. Disc brakes all day long. Far easier to maintain and service. Far better in braking performance than drum brakes.
Thanks for the great comments👍🏻👍🏻🛠