DIY How To Replace All Front & Rear Shocks On Jeep Wrangler TJ 1997-06 Procomp Rancho Bilstien Fox
HTML-код
- Опубликовано: 5 сен 2024
- #jeeptj #jeeplj #shockreplacement
Buy shocks: 0-3” amzn.to/3pyQV2B
Buy shocked 3-4” amzn.to/3x6aOjX
Official ATEM OFFROAD’s Super Store
www.amazon.com...
More Awesome Content?
DIY Overland kitchen Tailgate table
• DIY Jeep Wrangler Tj ...
DIY Bolt On Hi-Lift J-Mount Install
• Video
DIY Front Stubby off-road bumper
• Jeep Wrangler TJ - DIY...
DIY Body Lift
• Jeep Wrangler TJ - DIY...
Jeep front and rear shock replacement
• DIY How To Replace All...
Sway bar quick disconnects
• $20 DIY Jeep Sway Bar ...
Overland Tool mounting Solutions
• DIY Overland Trail Car...
Jeep Tailgate table build
• DIY Jeep Wrangler TJ T...
DIY Jeep Rock sliders
• DIY Jeep Wrangler Rock...
How To Install cb radio in Jeep Wrangler
• How To Properly Instal...
32” tires I’m running
• 32” Tires On My Jeep W...
DIY On board air compressor build
• Jeep Wrangler Tj | Lj ...
Fuel and water cell mounting Solutions
• DIY Overland Jeep Wran...
DIY Rear Trail Cargo Rack build
• Jeep Wrangler- DIY Ove...
Hi jack hood mounts install
• Jeep Wrangler How To I...
Wireless winch controls
• How To Install An Opti...
DIY Jeep E Fan build
• DIY JEEP WRANGLER Elec...
JEEP Wrangler TJ: How To Replace Front & Rear Shocks With 0”-6” Inch Lift XJ JK LJ
DISCLAIMER
Due to the factors out of control by ATEM OFFROAD, we cannot guarantee against improper use or unauthorized modifications of this information ATEM OFFROAD assumes no liability or responsibility for property damages or injuries incurred as a result of any information contained in this video. Use this information at your own risk . ATEM OFFROAD recommends safe practices when working on vehicles and or with tools seen in this video, any injury damage or loss that may result from improper use of these tools equipment or from the information contained in this video
Is the sole responsibility of the user and not ATEM OFFROAD. Be Safe
This video and description contains affiliate links which means if you click on one of these product links, I’ll receive a small commission.
You should not use petroleum products on rubber parts.
joe pro that’s correct, should always use silicon based grease on real rubber parts, thanks for bringing that to thought! While Vaseline and other petroleum products may degrade real rubber (actually made from the rubber tree), current o-rings and bushing technology does not use natural rubber. They are made of Polyurethane (urathane) ... With this in mind, you should have no worries about whether to utilize Vaseline on any of the bushings.Also if an bushing is made from, nitrile, for example (a material used in car fuel and oil lines) then there is no problem using petroleum grease to lubricate the bushing as this current technology is resistant. Cheers!
Well done video. Easy to follow , clear speech , good camera angles. Nice job dude
#programa LATE SHOW# 💥 thanks buddy I appreciate it , this was a fun one , cheers!
I love the ratchet hammer...lol. Well done
Nice, it comes in handy.. cheers
Video Great and clear instructions that even a complete noobie like me was able to complete it! ( I had some reservations, but this video helped). The bushings in the upper half of my rear shocks were GONE, knocking sounds going over every little bump! I was able to change the rear shocks on my '04 Sahara. Slight moment of panic when I clipped the tie off the shock and it started coming down at my face (rather quickly) but was able to maneuver it into place in time! Riding smooth now! Thanks a million!😃
No problem and those shocks you have are called twintube , they will work but completely different than the shocks I run on my tj. I use monotube, so you don’t have to clip off ties on those. Thanks for watching 🍻
You got really lucky on the rear.. I had to drop my tank.. nightmare job if it goes south.
💥, I know right! That’s horrible! Better luck next time👍🏼. Thanks for sharing and watching! Cheers!
Broke bolts. Had to cut hole from inside and grind out nuts. What a mess
Mega helpful. Most succinct instructional video I’ve seen.
Good video bud, doing a shock and stabilizer install on my TJ today.
💥 nice, it was a fun little project, thanks for watching, I really appreciate it!
Nice, well done and very informative.
Hey, if you have any comments or questions feel free to ask. Thanks for watching
Good work brother.
Thanks bro, and for watching I appreciate it!
Good video and good advice on using penetrant on the fasteners prior to removal. However, you should NEVER, EVER use anti-seize or oil on wheel lug nuts / bolts. If they are rusty, clean them with a wire brush, but leave them dry. If you lube lug bolts / nuts, you change the co-efficient of friction resulting in more force per indicated torque. The torque wrench may indicate 85 ft lbs, but the actual torque may be 95 ft lbs. This causes the bolt to stretch resulting in premature failure. Thanks!
Thanks for sharing and watching 🍻
Thats a Wrong! Nothing wrong with anti-seize on lug bolts. Come up North with some salt. C5A and torque to spec.b
Great informative video!!
*Chock, not chalk. But thanks for making the vid.
Also, since you're espousing good shop practice (which is a very good thing), there are a couple of other things worth pointing out
1.) Torque specs for lug nuts is for dry torque. Using any kind of lubricant at all (including leaving WD-40 on the threads) will change the torque value relative to what your torque wrench reads. This can and often does lead to one of two problems: under-torqued nuts that come off while driving, or over-torqued nuts that stretch the threads. No manufacturer has ever recommended using anti-seize on wheel studs.
2.) Good shop practice also includes wearing gloves at all times when working with anti-seize. That stuff is very toxic and can cause severe skin rashes/chemical burns, but it can blind you permanently if you rub your eye and get some in there. It's also extremely hazardous to aquatic life so be sure to do what you can to minimize how much goes into sewage or run-off (such as wearing gloves so you don't have to wash any down the drain).
Otherwise, the video was accurate and informative. The advice to soak bolts and studs in WD-40 and especially the warning about the rear shock upper mounts being welded inside the frame is crucial info and it's great you called that out.
Thanks for the comments on my addition to the lug nuts as you are correct about torque values. I actually stopped showing the ample use of this product in my videos as some do not understand how it works in conjunction with torque specs. There are several good videos and technical engineering data on how to properly apply a light coat of anti seize to wheels studs. (Essentially reducing torque)With this being said I don’t advocate it at all. The factory and I have two very different goals:
The factory doesn’t want the wheels to come off. I want my wheels to come off.
BTW just one data point: I’ve been putting on anti-seize for 15 yrs now and never found a loose lug nut. On and off road constantly changing and swapping wheels from one jeep to another
absolutely great video! thank you!
Glad I can help ! Thanks for watching 🍻
That tool you called "channel locks" is actually a locking pliers. Most people call them Vice Grips since that was the original brand that made them.
Channel-Lock makes lots of different tools, but most people still call adjustable pliers "channel locks" for the same reason they call locking pliers "vice grips", circular saws "skill saws", an occilating tool a "fine (Fein) tool", a reciprocating saw a "sawzall" (or worse, "sawzaw"), etc. ✌️
I do call them out correctly Watch 2:05 of this video!
And Nice catch , but I know they are vice grips pliers , I just didn’t have the right words in my mind to call them out correctly at that time in the video. I do think I did eventually call them out correctly sometime in the video! Hahah Thanks for watching 🍻
Thank's,very helpful video.
💥 nice, thanks for watching
good vid. ty
Thanks. Great video with clear instructions. Can you use grease instead of Vaseline to lubricate the bolt bar?
A lithium grease won’t hurt , but just some dawn dish soap would be good to
@@ATEMOFFROAD Thanks!
Thnx bud ! 10-4 on the vids. My turn. Over n out
💥 nice, thanks for watching! Cheers
I ordered the correct shocks for my Jeep, however the bottom bushings are too wide to slip into the bracket.
Should I hit on them to force it in ? ?
Sometimes when the bolts are tightened the bracket flexes inward and can be bent. I just use a crescent and bend then back outward slightly so the new shock fits. It’s usually not the bushing but the metal spacers that won’t fit . 🍻
Hate to be THAT guy but...
It's "Chock" your tires, not Chalk.
Thumbs up Bro.
👍
Hahahah 😅 thanks for watching
Good video
Petroleum jelly eats rubber. Use a silicone based lubricant.
That’s correct, “REAL Rubber from the rubber tree” we have already discussed this in the comments, lots of information there>>>
Thanks for watching
I noticed that the rear shock was rubbing on the coil spring perch when installed the lower bolt have u had any problem with that.
Since the install I haven’t had a problem even since the last time I’ve been wheeling , they don’t touch right now, was considering trimming perch or relocating on the shock bracket. I’ve even seen guys flip the shocks but considering all that I may Re axle all together soon to 8.8 so it hasn’t been a total issue yet, but still in the back of my mind, I bet it would bother a good suspension mechanic that I let this go haha , cheers!!
@@ATEMOFFROAD They make shock adapters that move the rear shock away from the spring perch. Extreme Terrain or Quadratec sell them. Easy install and work well.
@@erikdahl3171 yep just recent installed them on both jeep red and green! I love them , check out my diy 4” lift video. Thanks for watching @Erik Dahl
Shocking .....Just Shocking !
William Smith I’m shocked haha thanks for watching! Cheers
Do you jack up the Jeep just so you have more room or does it make it easier to have the wheels hanging?
No you don’t need to jack up the jeep, I just removed the wheels so y’all can see and there’s more room to work on them. You can probably do a hard driver on the steering wheel to take the passenger side off and vise versa. Without taking the wheels off. 🍻
But my question is, do you need to jack up the jeep to do the shocks?
@@MrRyanlipp1980 no
That jeep aint ever seen a salted winter road
It’s a california jeep we have it all mountains, desert, Pacific Ocean, grasslands , foothills. Ha this jeep has been all over the place 🍻
Did the new shocks make a difference in the ride comfort and control? I think my shocks might be stock, from 1999, and it has a 3 inch lift. Been driving it like that for 6 years and it rides as rough as a really old farm tractor 🥴
Good shocks definitely help out with ride quality but good coils will too! Especially if you have something better than single rate coils like dual or triple rate! Also if your going offroad try disconnecting the front sway bar end link. This will make the front axle live and wake up the suspension for way better ride quality offroad! I have a video on this topic about sway bars on the jeep! Thanks for watching cheers
What tires and rims are those they look clean
Thanks , those are eagle alloy wheels , can find them on Amazon and eBay! Thanks for watching
@@ATEMOFFROAD thank you for making a good vid and this is making me want to get some new shocks and those wheels are nice
@@Fishslayer04 no problem, I hope you can find the ones you like 👍🏼
@@ATEMOFFROAD sorry to ask a million questions but can I get a link for both the front and rear shocks I could only find rear not front
@@Fishslayer04 no worries bro, I don’t have a link but 4wp stocked these shocks - was best deal I could find, what I did was go on the procomp website , choose my lift and selected the shocks I needed and copied part numbers. they have different models to choose from , I’d start there , they also offer a selection of places where you can order the shocks too
Do you adjust the shocks or just put them straight in?
No adjustment on these, thanks for watching 🍻
Chock not Chalk
@@arolon9173 🤣
it looked like the rear shock you installed was super tight to the strut, would it rub against that and damage the new shock?
💥 nice, thanks for watching it looked tight but the shock clears with a small gap between the spring perch and shock body. If your spring perch touches you can sand or notch some out with a angle grinder to be on safe side
WD-40 doesn't work as a penetrant
Nice, thanks for watching, maybe try pb blaster.
wd-40 makes penetrating fluid
Third bullet point on front of original formula WD40 can: Loosens rusted parts
Sssssoooo no boots on your shocks?😕
CHOCK your wheels!
Chalking them won't help much.
😂😂 thanks for watching , must be the Canadian in me
ruclips.net/video/tyha9CRpBQU/видео.html
You lost my confidence when you used your ratchet as a hammer. ALWAYS use the RIGHT tool for the job!
That’s Fair! But silly all at the same time! Look closer is a ratchet/ hammer. Wera 8002 C Koloss 1/2 inch Square Drive Ratchet with Hammer,5003692001 a.co/d/1RP2nth
The ratchet is well over made to handle the same forces applied as if it were to drop 6 feet from the ground. Should you not drop your tools? It may not look safe but it was well worth purposefully dropping the tool than going back to the box to get a hammer thats well over made for this task.. I seriously do not advocate the improper use of tools. But we are assisting the movement of a loose bolt here. 🤷♂️
Anything is a hammer if you know how use it correctly
Looked like a hammer to me
Chalk the rear tires??? how about Chock lol
That’s flair , 😅😅 y’all get me every time!
Good video! Thanks 👍
Thanks for watching