Thank You oh Obe-Wan of the Garage galaxy! Got a 2003 S10 and had to replace the steering gear and steering lines after 500k miles. DOES NOTHING EVERY LAST?!?!? btw - I CONCUR on the taco statement 1000000%!!!! Tks Dude. You saved Me a LOT of grief and was MUCH easier than I thought.
For some reason, 18mm is very often missing from flare nut wrench sets, despite it's being a very common size on power steering hoses. My local Menard's sells flare nut wrenches in sets and individually, yet not a single 18mm could be found. I finally had to buy one from Amazon.
When you bleed the lines for the power steering, do you mean let it run ,while turning the wheel, with the cap off?? And for how long? And when do you know when there’s no air in the lines?? Thanks for the video. It was the only one I found where the steps were clear and informative.
There's no exact method to it really, just top it off, run the engine and turn the wheels back and forth a couple of times, shut it off for maybe 5 min to let the air bubbles vent and then do it again, may take 2 or 3 tries before most of the air is burped out
I replaced my power steering pump same vehicle for a new reman pump. Brand new high pressure line. New pulley. New belt tensioner. New serpentine belt. BLEEDING THE OLD FLUID OUT,,,, You can leave the low pressure hose disconnected to a bucket,, fill the power steering fluid in the reservoir,, disconnect the ignition coil,, bump the starter a bit,, and all the old crappy metaly fluid in the steerbox and system will get purged. Might add an in line filter on the low pressure hose as well providing its a high enough flow.
Yeah that can be a difficult part to do because the lack of room, if the fitting has been cross threaded at all and partially tightened then you might have to remove the fitting on the back of the pump housing and try threading them together first and then installing it back onto the pump, also if it looks like the line isn't angled straight enough, you might try slightly bending the line so the angle works better for you, good luck!
If i remember correctly, i believe there are o-rings on the ends of the fittings that should seal it up, and just snug em up, if you tighten too much you can damage the o-rings
Thanks for the video! I am replacing mine at the moment. The problem I’m having is the the high pressure line fitting on the gearbox is not biting the thread. The new part is Gates. Any trick to get it in sir?
Not really any special trick, it just has to be damn near perfectly lined up before the threads will grab, also try pulling up on the line while pushing down on the fitting, i don't know why or how that helps with starting the threads but it does
You're doing people a great disservice by NOT disclosing that your vehicle is the 2-wheel drive variety without tow package. The 4x4 versions have a huge cross-member under the steering gear that makes access to the back of that pump virtually *impossible*, and the return line circuit is totally different on units with tow pkg due to the p/s cooler. This video is yet another example of a subject not researched thoroughly enough.
Your complaint is yet another example of a whining troll. I have a similar 4x4 S10 with no access from the bottom. I would love to see YOUR video of how you handled the problem.
For those of you with a 4x4 S10 with no bottom access to pump, here is a link to a document which outlines the procedure for removing & installing the pump. Coupled with this excellent video, the document may be of help. Ny vehicle is a 2001 Chevy S10 4x4 ............. docs.google.com/document/d/1hzeESC1E2lswpM1Bj0rmFlW2JQLCsCNC/edit?usp=share_link&ouid=103651151372989198589&rtpof=true&sd=true
Thank You oh Obe-Wan of the Garage galaxy! Got a 2003 S10 and had to replace the steering gear and steering lines after 500k miles. DOES NOTHING EVERY LAST?!?!? btw - I CONCUR on the taco statement 1000000%!!!! Tks Dude. You saved Me a LOT of grief and was MUCH easier than I thought.
Thanks for the wrench sizes.
18 mm is the only wrench I don't have for some reason.
For some reason, 18mm is very often missing from flare nut wrench sets, despite it's being a very common size on power steering hoses. My local Menard's sells flare nut wrenches in sets and individually, yet not a single 18mm could be found. I finally had to buy one from Amazon.
11/16 will do
Thanks for the video. I followed your instruction and replacing the high pressure hose went easier than I expected.
Really helpful video. Thank you for including all the sizes of the fittings.
He's videos are very good and detailed start to finish nice job on videos
Thanks man!
Very helpful, im currently trying to replace the lines on a 2000 bravada with no idea what im doing but this video has helped a lot thank you
Thanks for the insight man 😊. I'm about 5 mins away from this exact task lol. 😅
Cheers!
When you bleed the lines for the power steering, do you mean let it run ,while turning the wheel, with the cap off?? And for how long? And when do you know when there’s no air in the lines?? Thanks for the video. It was the only one I found where the steps were clear and informative.
There's no exact method to it really, just top it off, run the engine and turn the wheels back and forth a couple of times, shut it off for maybe 5 min to let the air bubbles vent and then do it again, may take 2 or 3 tries before most of the air is burped out
Grasias por su video compañero
This vid kicks ass
I replaced my power steering pump same vehicle for a new reman pump. Brand new high pressure line. New pulley. New belt tensioner. New serpentine belt. BLEEDING THE OLD FLUID OUT,,,, You can leave the low pressure hose disconnected to a bucket,, fill the power steering fluid in the reservoir,, disconnect the ignition coil,, bump the starter a bit,, and all the old crappy metaly fluid in the steerbox and system will get purged. Might add an in line filter on the low pressure hose as well providing its a high enough flow.
That's excellent advice! I've done that several times in the past when the fluid looked like burnt ass
Great video.....good job
Thanks for the video; I have an 2001 Chevy s10 are they pretty much the same way?
Yes, should be exactly the same
Thanks for doing this. I'm having a hard time getting the line screwed in on the pump side. Any suggestions?
Yeah that can be a difficult part to do because the lack of room, if the fitting has been cross threaded at all and partially tightened then you might have to remove the fitting on the back of the pump housing and try threading them together first and then installing it back onto the pump, also if it looks like the line isn't angled straight enough, you might try slightly bending the line so the angle works better for you, good luck!
love the taco hat...lol . where did you get the ice socket tool
Good video !!!!!
How tight should I tighten the fittings? I’m having leaks on both fittings
If i remember correctly, i believe there are o-rings on the ends of the fittings that should seal it up, and just snug em up, if you tighten too much you can damage the o-rings
Thanks for the video! I am replacing mine at the moment. The problem I’m having is the the high pressure line fitting on the gearbox is not biting the thread. The new part is Gates. Any trick to get it in sir?
Not really any special trick, it just has to be damn near perfectly lined up before the threads will grab, also try pulling up on the line while pushing down on the fitting, i don't know why or how that helps with starting the threads but it does
Do both the high pressure line and the return get o rings ? Or just the high pressure side ?
@MrJackfrost84 yes they should both have o-rings
What is the name of that pivot head open ended wrench attachment you have?
I got them on Amazon, flare nut socket set, the metric set is rarely available, the SAE set is available most of the time
Whats the name of the thing attached to the linesv
There's the oil filter adapter which is what the oil filter threads onto, and then there's the oil cooler line manifold
What fluid did you use?
Just basic power steering fluid from parts store, nothing special
@@theman9764 cool thanks
line wrench socket tool
@@randallcapps7352 Dynamic 3/8" Drive 10 Piece... www.amazon.com/dp/B013H2YUXA?ref=ppx_pop_mob_ap_share
You're doing people a great disservice by NOT disclosing that your vehicle is the 2-wheel drive variety without tow package. The 4x4 versions have a huge cross-member under the steering gear that makes access to the back of that pump virtually *impossible*, and the return line circuit is totally different on units with tow pkg due to the p/s cooler. This video is yet another example of a subject not researched thoroughly enough.
Your complaint is yet another example of a whining troll. I have a similar 4x4 S10 with no access from the bottom. I would love to see YOUR video of how you handled the problem.
For those of you with a 4x4 S10 with no bottom access to pump, here is a link to a document which outlines the procedure for removing & installing the pump. Coupled with this excellent video, the document may be of help. Ny vehicle is a 2001 Chevy S10 4x4 .............
docs.google.com/document/d/1hzeESC1E2lswpM1Bj0rmFlW2JQLCsCNC/edit?usp=share_link&ouid=103651151372989198589&rtpof=true&sd=true