How to install PVC Bathroom Wall Panels

National Plastics show you how easy it is to transform your bathroom with PVC bathroom wall panels. From which tools you need to install and how to measure, this video shows just how straightforward it is to make your bathroom dream a reality.
Browse and buy our selection of bathroom wall panels online: www.nationalpl...
All of our bathroom wall panels can be delivered direct to your door and we offer FREE DELIVERY for all purchases over £100 (ex vat). You can also purchase direct from one of our nationwide branches, visit us today.

[@CoolDude-tz5co]

Excellent video, gets straight to the point with no nonsense, thanks

[@czeital]

Good start but nothing on how to get that width cut correct if you need whole panel to corner - ie: if things are out of square etc and also are panel widths stated in/ex tongue and how are trips accomodated in width calcualtion. Also saw nothing on how to deal with the bottom when it's meeting a bath which would be great to know thanks

[@nairagasparetto]

It could be installed on a existing tile wall?

[@terrybenedict1]

VERY DRAMATIC

[@thespecialist7]

Hi should you prime the wall first ,I am using plasterboard. Using Silicone to stick the wall panels. Or can I just plasterboard the wall first?

[@NarrowboatSuperB]

If you have plasterboard that has not been skimmed, just use PVA, mix pva with water, brush it onto the board.

[@brrymcgolly]

Oh yes it looks very easy but they don't tell you about the awkward cuts when you get to the end. You can't guarantee not all bathrooms a square.. but a very good video

[@ealingbroadway2000]

That’s why you measure, we had height differences that went into a slant from corner to corner, that was a real pain

[@alistermcnicoll2634]

If putting on top of existing tiles is there not a problem of getting pipe connections of controls etc through the extra thickness?

[@NarrowboatSuperB]

Most of these boards are 5mm

[@evashell]

Can you stick on top of old tile.As i will be using it as a kitchen splash back.

[@aimansaleem6166]

What is the material of these pvc?

[@silverbackag9790]

PVC.

[@RichardCropper]

Can this be applied over wall paper?

[@shaidanasreen134]

What about around the bathroom window or is this just suitable for straight wall, if you can pleas make video

[@cokhitonghop9256]

Well done

[@samuelhara4874]

How do you fit the last panels

[@dobarjepostenje662]

Can you put this wall panels on any type of wall? If I start doing this on which things I should be careful about

[@vcsradio2805]

Good job. Can this board be applied to a cement wall

[@gregc7699]

Yes

[@asmarahi3311]

Can we do colour on pvc panneling

[@MidnightMoonlight92]

Can I put wall panels over Artex?

[@Xan-zh5ni]

Hi how would I replace a damaged panel?

[@pvclover76]

Do I need to put a bead of silicon in each side of the corner trim before pushing the panels in ?

[@ebayseller6040]

can I make a table using this??

[@frackend9035]

ONE HUGE PROBLEM! THEY DON'T HAVE A STORE IN U.S.A?

[@svkscorpio]

Doesn't water seep in between the panels and cause the wall to dampen and also growth of mold behind them?

[@chrisbelfast6662]

No because you will use trims for the ends on the panels so it's water tight

[@alanoliver5378]

As instructed in the video, apply silicone sealer to the TnG joint of each panel.

[@privatechannel8462]

​@@Parkertannerzi did this, then found out it was me

[@ealingbroadway2000]

PVC cladding panels come in different sizes, mine were 8’x4’ and easier to work with, only needed 3 and shorten height on them.

[@davidhayes1950]

The pannels are tongue and groove and the bead runs round the side but don't bother measuring the bead just scribe it off the aqua panel that you have cut ready to put in and your adhesive should be put on like dot and dap and don't bother putting the nozzle on your adhesive as you need it to come out in big blobs once every 150 mm across and down doesn't have to be a exact and avoid putting the adhesive near the edge as it will squirt out around the edge of the panel but do put the nozzle on the silicone and do a bed of silicone were your gonna place the qua panel which will give you your added protection but make sure you wipe off clear any smudges of silicone/adhesive that get on your board showertray/bath because you want to put a neat bead of silicone on after the install is complete
I install these all the time so any questions just ask

[@flexhex3334]

what panel is this, im looking for it on your website and cant find it. Many thanks

[@Immortaljme]

Can you use these panels on top of existing wall tiles?

[@twobins2060]

Yes

[@thelargest7614]

Of course, that would be even better probably.

[@markbellars6961]

If you fit over existing tiles surely the end trim will sit off the wall by the depth of the old tile and look weird.

[@garydouglass9577]

You didnt use your staple gun to the edge of panels.

[@GJLCreativeStudios]

is that what its for? I was wdnering about that

[@Devon-x1u]

BTW I am not watching this to go back to bed i.e. the MUSIC please heavy metal anything but this

[@redguern]

Ha ha! I agree with you.

[@sophiemagsx]

Hi , are you in London? Would you fit this for me x

[@Japanese_one_Tokyo]

No. We are busy!

[@sosolife]

☺️👍

[@dejantrifunovic3009]

Sare se ne uklapaju prirodno kao laminat na podu

[@almirhusanovic8128]

I can see anything here

[@martincholman2]

It's not even a bathroom