This is exactly what my truck is doing U1428. P2122. P2138. I’m in limp mode and it says low voltage connection! This video is super help to trouble shoot thx man!!!!!
I’m having codes P0642, P2122, and P0522 on my 2010 Chrysler Seabring. The car cranks but it won’t start over, and it drove perfectly fine the day of. I’m currently stuck on what it could possibly be, any help??
I'd check the wiring either on a volt meter or scan tool, perform a wiggle test and see if there's legit wiring issues 1st. Hard to say via message weather it is or not. Hopefully the video assisted you
Please, how can I fix the problem? I was called to another garage to fix a 2005 300c chrysler. The problems they noticed with the car was Hard or no start, red lightning bolt flashing, no throttle response, headlight stays on, immediate stalling after starting and rough idle throughout idling as a result a new PCM was replaced with a new one however problem still persisted. I scanned for DTC codes and saw a P0340, P2167, P2166, P2115, P2116, p0603 and more module codes like C2202, U0168, U1414, B1A25, etc.
Really quick... have you tried monitoring CMP pid data? If this is the easiest to access and immediate come back after clearing, check power, ground and signal at the cam position sensor. Because the ground or power source maybe missing and they're all related in some way. This is me off the top of my head
So Where is the I have wk 2010 It is the same problem The codes p2122 p2127 p2138 I change the pedal and clean the throttle body and replace it connector And it is the same problem
This is exactly what my truck is doing U1428. P2122. P2138. I’m in limp mode and it says low voltage connection! This video is super help to trouble shoot thx man!!!!!
I'm getting the same code along with p0642,p2135. I've replaced the etc. It won't start at all...
I have the same code. Replaced the pedal and throttle body and still in limp mode
Same problem
Same here
Same here
@@EDjustthatcool ⁰0⁰
Same like me
My 07 Jeep Wrangler is in lilp mode. It's must be the TPS. 120 USD part.
Amazing
I’m having codes P0642, P2122, and P0522 on my 2010 Chrysler Seabring. The car cranks but it won’t start over, and it drove perfectly fine the day of. I’m currently stuck on what it could possibly be, any help??
What if you get P2122 code but your TPS has also been on, would it more likely be the TPS?
What's the TPS code?
My car is giving these codes P2115, P2116 Accelerator Pedal Position Sensor 1&2..do you need to cgange wires?
I'd check the wiring either on a volt meter or scan tool, perform a wiggle test and see if there's legit wiring issues 1st. Hard to say via message weather it is or not. Hopefully the video assisted you
Please, how can I fix the problem? I was called to another garage to fix a 2005 300c chrysler. The problems they noticed with the car was Hard or no start, red lightning bolt flashing, no throttle response, headlight stays on, immediate stalling after starting and rough idle throughout idling as a result a new PCM was replaced with a new one however problem still persisted.
I scanned for DTC codes and saw a P0340, P2167, P2166, P2115, P2116, p0603 and more module codes like C2202, U0168, U1414, B1A25, etc.
Give me a few to answer this. I'll look into it when I'm free. I'm just acknowledging I see and read
Really quick... have you tried monitoring CMP pid data? If this is the easiest to access and immediate come back after clearing, check power, ground and signal at the cam position sensor.
Because the ground or power source maybe missing and they're all related in some way.
This is me off the top of my head
@@partsshooter Please, what should the CMP sensor value be?
@davidessien5465 compare with the other bank. I'm referring to the wiring going to pcm and not sensor itself.
@@partsshooter ok. I'll check that.
I keep getting a P2127 Code that says throttle Control on a 2019 Ram 1500 P/U.
What have you done in effort to fix this?
Well for now I use a code reader and just reset it. I have to get it in for repair.
@@leskeegan9033 I gotcha
It's on a2012 avenger
Still running smooth without replacing the pedal?
Yup!
@HUBERT LEWIS yup
So
Where is the
I have wk 2010
It is the same problem
The codes p2122 p2127 p2138
I change the pedal and clean the throttle body and replace it connector
And it is the same problem
I have the same problem, you already fixed.?
@@eriklopez6143 you fix it?
@@Untied223 yes, my friend works at cummins and I repair it .. he told me the pedal cables that connect to the computer.
@@eriklopez6143 oh thanks man
" conneggtore " ....hmmmm ...