Thanks! Condensate trap was sludgy. Appreciate that tip. Note to homeowners to put a bucket under trap when you unclip and clean it out as you’ll get 1/4 cup of gunky water coming out.
Great video . I liked how you point out that the exhaust pipes were too close , I will make sure my install is done correctly and have the screen covers followed by keeping them apart . Cheers 🇨🇦
This was an exact replacement for the old one that lasted about 10 years. ruclips.net/user/postUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh The top of my mitigation tube by my roofline was just a 90 elbow which allowed too much debris to fall down into the fan, eventually ruining it. Without this issue, I bet it would have kept running another 10 years. When I replaced this fan, I added an extra elbow joint so the top tube now it does a 180, which should solve that problem. The radon guys around here wanted to charge me a $300 diagnostic fee, then parts/labor (probably close to $600 total). I installed this all by myself in about an hour for the cost of the fan; it would probably be even easier/faster with two people. FYI the manufacturer's warranty greatly differs depending on whether you install it yourself (1 yr warranty) or have a licensed installer do it (10 yrs).
Dude, you just made me look like a superstar. Pregnant wife at home and woke up to a 58F house. Fixed in 10 min. You're the man. Put a bucket under that plug. Sludge comes out!
Thank you for the video - the second issue haloed and got my water heater working again. Will wait and watch to see if it’s working as expected now. Thanks a lot though. 🙏
Thank you sir! I didn’t think to look at the condensate drain. I was hearing a gurgling from the boiler. I couldn’t understand how air would be getting in the system but that’s because I wasn’t. The gurgling was from the condensate. I saw an e003 error and e110 errors for reference. About a half cup of water came out of the drain then gurgling sound was gone.
Thank you. Would u know why my heater won’t turn on? There’s no display in circuit board when turned on. Is there a reset button somewhere? Model NR 240. Thanks!
I got a nasty surprise when I removed the white cap, ensure to put a small bucket under! Any tips for dropping PSI? My max is 16.7, I recall it used to hit 22 a couple years ago.
Thanks. Mine would not turn on. I was getting error 22. Then I was getting error 27. My air intake screen was pretty dirty. Cleaned it. Still wouldn't go. Went outside & cleaned what I think was the soffit vent for it. Still wouldn't go. So next I pulled off that water condensation catcher cover. What a mess! Should have warned me to put a small bucket under it 1st. Filthy water went everywhere. About 1/2 liter I'd guess. I put the cover back on while still spraying out. I wasn't sure if it would stop. If maybe it was perhaps needing the input water shut off. But I went & got a small bucket & tried again & it did finish running out pretty quick after. I had a big mess of filthy water spray to clean up. The white cap was quite full of grunge. Had to dig it out about an inch deep. Compacted dirt. Then I cleaned it & put back in. I cleaned all inside the unit, also the outside & all around to make it look nice. And have it all dry. I gave it a quick check & turned it on. It works. Yay. So I guess I was experiencing both of your 1st two common issues. My unit is a Navien NP240 NG. I live in White Rock, British Columbia, Canada. Thanks for saving me hundreds of dollars. Didn't cost me a dime.
My 3 way valve went on mine and it is only 2 yo. The symptom was 777 LWCO going off every now and then. Found only once summer hit because another symptom is that the base board pipes got hot when water called. Finally got no hot water.
The mask was to much. Never once wore one. If someone asked I told them it was a safety hazard. Most people that wear them are to stupid to realize you aren’t serious. Otherwise call someone else.
Хобби
I cleaned the trap on the bottom. It was filled with dirt. The hot water worked right away. Thanks a lot.
Thanks! Condensate trap was sludgy. Appreciate that tip. Note to homeowners to put a bucket under trap when you unclip and clean it out as you’ll get 1/4 cup of gunky water coming out.
Great video . I liked how you point out that the exhaust pipes were too close , I will make sure my install is done correctly and have the screen covers followed by keeping them apart . Cheers 🇨🇦
You just saved me hundreds of dollars and got my heat back on, thank you sir!
This was an exact replacement for the old one that lasted about 10 years. ruclips.net/user/postUgkx7yWIKcrbA9KMHkGSfcgxW2lsjHT6B8Sh The top of my mitigation tube by my roofline was just a 90 elbow which allowed too much debris to fall down into the fan, eventually ruining it. Without this issue, I bet it would have kept running another 10 years. When I replaced this fan, I added an extra elbow joint so the top tube now it does a 180, which should solve that problem. The radon guys around here wanted to charge me a $300 diagnostic fee, then parts/labor (probably close to $600 total). I installed this all by myself in about an hour for the cost of the fan; it would probably be even easier/faster with two people. FYI the manufacturer's warranty greatly differs depending on whether you install it yourself (1 yr warranty) or have a licensed installer do it (10 yrs).
Dude, you just made me look like a superstar. Pregnant wife at home and woke up to a 58F house. Fixed in 10 min. You're the man. Put a bucket under that plug. Sludge comes out!
Thank you so much!!! Single woman here out of warranty!!!!
This was really helpful, it saved me a visit to hvac .. the issue happened on Thanksgiving it was a nightmare.
Super helpful and I really appreciated the sound effects 🔊👍
Good job on the video and good job on catching those vent terms being too close
Thank you for the video - the second issue haloed and got my water heater working again. Will wait and watch to see if it’s working as expected now. Thanks a lot though. 🙏
Thanks al lot
You saved my life LOL
E-10 error and another number 27 as well
I cleaned the one in the bottom and the filter too
Works again
Thank you
Thank you brother
Thank you!!! I can take a bath now! That condensation plug thing was full.
Thank you sir! I didn’t think to look at the condensate drain. I was hearing a gurgling from the boiler. I couldn’t understand how air would be getting in the system but that’s because I wasn’t. The gurgling was from the condensate. I saw an e003 error and e110 errors for reference. About a half cup of water came out of the drain then gurgling sound was gone.
Very helpful. Thank you!
Thanks for making the video. Don’t listen to the negative Nancy’s
Thx theres another better 1 I made on my videos. Was clearer and wasnt mirrored. You can find under videos
This helped thank you
Thank you. Would u know why my heater won’t turn on? There’s no display in circuit board when turned on. Is there a reset button somewhere? Model NR 240. Thanks!
I got a nasty surprise when I removed the white cap, ensure to put a small bucket under! Any tips for dropping PSI? My max is 16.7, I recall it used to hit 22 a couple years ago.
Need pics not sure what water feeder or regulator you have
Can you explain the correct orientation of the condensation trap? I got dripping from the white cap after cleaning. TIA
Thank you!
Np
Thank you ❤
Thanks. Mine would not turn on. I was getting error 22. Then I was getting error 27. My air intake screen was pretty dirty. Cleaned it. Still wouldn't go. Went outside & cleaned what I think was the soffit vent for it. Still wouldn't go. So next I pulled off that water condensation catcher cover. What a mess! Should have warned me to put a small bucket under it 1st. Filthy water went everywhere. About 1/2 liter I'd guess. I put the cover back on while still spraying out. I wasn't sure if it would stop. If maybe it was perhaps needing the input water shut off. But I went & got a small bucket & tried again & it did finish running out pretty quick after. I had a big mess of filthy water spray to clean up. The white cap was quite full of grunge. Had to dig it out about an inch deep. Compacted dirt. Then I cleaned it & put back in. I cleaned all inside the unit, also the outside & all around to make it look nice. And have it all dry. I gave it a quick check & turned it on. It works. Yay. So I guess I was experiencing both of your 1st two common issues. My unit is a Navien NP240 NG. I live in White Rock, British Columbia, Canada. Thanks for saving me hundreds of dollars. Didn't cost me a dime.
how long did you own yours before it started acting up
Can you go over flowtech water treatment. Does it work?
I only work on heating side of plumbing. Not whole house filters. But they do work
My 3 way valve went on mine and it is only 2 yo. The symptom was 777 LWCO going off every now and then. Found only once summer hit because another symptom is that the base board pipes got hot when water called. Finally got no hot water.
It was covered under warrantee but not labor. Paid over $500 to fix.
I have a code e.594 what could it be thanks
Thanks for wearing your mask for us.
lol
That didn’t age well 😂😂😂😂
SHEEP
🤣🤣🤣
The video is a "reverse" image. Everything is backwards.
I’m confused what are you showing
To painful to watch
I have another one with better video. Its not mirrored and i dont have a mask on
The mask was to much. Never once wore one. If someone asked I told them it was a safety hazard. Most people that wear them are to stupid to realize you aren’t serious. Otherwise call someone else.
No sabes de la bronca que me sacaste
Subscribe
The hot water problem is the last of your worries if you must wear a mask in and outside of the house, I cant understand what you are saying,
Theres another video with info maybe can stop crying about it
Can't understand you with mask on.
BUDDY, HOW THE BOILE AND NOT YOUR FACE
Check another video of mine with better film. Same 3 problems
Why are you wearing a mask?
your camera work gave me a stroke
Good info but very annoying video.
Does that mask keep the germs out out RUclips?
Very poor filming cant hear him..please practice your cinematography
Broo can't hear a word of what you saying, ERASE the video and make a new one
I have another 1 on my videos newer and clearer so you can stop whining
I wish this guy would take his mask off so he doesn't sound like Charlie Browns teacher. I can't hear him☹
cant hear you, maybe if you took the mask off?
Go watch someone else for free info
Take off the damn mask
why are you wearing a mask alone? its 6 feet distance
Because the homeowners were still worried about plandemic. I have another video of the exact same problem with better footage and no mask check it out
Why are you wearing a mask?