100%!! He knows his shit just as well if not better than pretty much anyone I've talked to about bikes! Also, much love, bro! I appreciate the support! 👍🏻
An induction heater is a great investment if you do this regularly....heats the bolt up in 30 seconds and no damage to paint. Also works great for primary shaft bolt that can sometimes gall from the red Loctite. If you work on cars than you know how difficult exhaust manifolds can be....simple job with an induction heater.
Everything was aligned when I put the timing chain/gears back on, and when my rear cylinder is at TDC my dots are off by two teeth. My crankshaft gear is at 11 o’clock and my cam gear is at 1 o’clock. Any ideas?
Yeah, alot dealers don't care for your eyes to be in the service department because of the hammering that tends to go on..lol.. I'm not a motorcycle tech/mechnic, but I work on my own bikes and my record with the Lifter cuffs bolt removal, without a break is 3-1..I lost the second one I tried.. used some heat, but did not want to flame it so/to avoid higher chance of combustion..yikes! You can hear the quality of that cam plate when you tap it on a hard surface.. Good point about locking the engine before adjusting the push rods
@@CassidyCarsonI haven’t seen a dealership that wouldn’t install a major manufacturer cam. I’m assuming you’re in California, dealing with CARB, which kills aftermarket/tuning performance.
@@wyattashley5871 Yeah, I expect there way more giggling in the military now than when I was in in the 70s and 80s. Still hard to listen to a man giggle like a school girl.
Nothing but love for Harley techs!
Bro this dude actually did a hella good job of explaining things 💯🤙🏽
Miller speed co. Is where it’s at for quality work and Bryce seems like a solid dude 👊🙌
Yessir! 100%
I'm going to install a cam on my 2022 Road Glide Limited. Thanks for the tips!
Thanks for this. If I could subscribe again, I would. This dude explains stuff most people dont think are important.
100%!! He knows his shit just as well if not better than pretty much anyone I've talked to about bikes!
Also, much love, bro! I appreciate the support! 👍🏻
An induction heater is a great investment if you do this regularly....heats the bolt up in 30 seconds and no damage to paint. Also works great for primary shaft bolt that can sometimes gall from the red Loctite. If you work on cars than you know how difficult exhaust manifolds can be....simple job with an induction heater.
Good video and explanation!
Did he check crank run out ? Didn't show it in the video
Greene Brothers Design!
I was thinking the same thing
What crash bar is that??
Solid crew @ Millerspeedco you won't find a better one.
💯
Cassidy I received a crankcase gasket with my cam bearing. I don't see anyone using a gasket on the crankcase.
Hey how do I prime the old without the bike starting
Everything was aligned when I put the timing chain/gears back on, and when my rear cylinder is at TDC my dots are off by two teeth. My crankshaft gear is at 11 o’clock and my cam gear is at 1 o’clock. Any ideas?
What size can did you use for it?
What do you keep disconnected to just prime the oil pump?
Yeah, alot dealers don't care for your eyes to be in the service department because of the hammering that tends to go on..lol.. I'm not a motorcycle tech/mechnic, but I work on my own bikes and my record with the Lifter cuffs bolt removal, without a break is 3-1..I lost the second one I tried.. used some heat, but did not want to flame it so/to avoid higher chance of combustion..yikes! You can hear the quality of that cam plate when you tap it on a hard surface.. Good point about locking the engine before adjusting the push rods
I got the Screaming Eagle cam on the Stage 2 a while back, I wonder what the labor cost would be if I wanted to upgrade to the S&S one.
It will depend on your local shop. As far as I know, most HD dealerships don't do aftermarket installs although some will 👍🏻
@@CassidyCarsonI haven’t seen a dealership that wouldn’t install a major manufacturer cam. I’m assuming you’re in California, dealing with CARB, which kills aftermarket/tuning performance.
What make is the engine guard on that bike ? . Thanks
Look similar to original garage moto crash bars
Join the Army, might be able to help you grow a pair.
Ha ha....I was thinking the same thing myself....way to much giggling.
Dude can’t be excited bout his new cam?? C’mon man smh.
@@jerrym2321 you must haven't been in the army in the last 10 years because giggles and jokes are the only thing we have. lol
@@wyattashley5871 Yeah, I expect there way more giggling in the military now than when I was in in the 70s and 80s. Still hard to listen to a man giggle like a school girl.
How much does that run.
How long does a cam install take ?
Depends on your tech really. Most shops would say about 4 hours I'd say? It really varies
At least 4 probably longer.
Wearing an Apple Watch hating on vrods is crazy 😂
I feel like if you are at base circle in the cam it should not rotate the motor as you run pushrods out 🤨
Dude giggles too much, stuff not even funny and he fake giggles about every thing, had to stop watching.
Agreed. Like a clown
Do we really need that annoying backgtound music for such a nuce tutorial like videos?
Why not just go with a S&S cam chest kit?
This was just the used kit I got. If I had just gotten the new package I would've probably just done all one or the other
Autofocus?
Sam smith 😂
All your giggling like a lil girl is difficult to get through. Have you come out yet?