Thanks man, you are a life saver. The diagram on the iflight page was so messed, I'm glad you made this video!! Going to solder up my gps now confidently.
I’m confused, why did you not installed the SD and CL wires? And where is it located to install? Will it work fine if I don’t install those 2 wires on my Nazgul evoque f6 v2?
I have the Evoque F5D with the Blitz mini F7 and DJI 03 air unit, and I connected the 5v,GND,Rx,tx to plug and the SDA and SCL wires soldered, but I cannot get the gps icon to light up in betaflight. I have gps turned on for UART4 and UBLOX turned on. The gps module has steady red light with a flashing green light, any suggestions?
That's all well and good but where can I find the TPU GPS holder that will attach to the frame so that I can secure the GPS receiver to my Nazgul 5 v2?
Hi I have the same model with dji o3 system and gps, i would like to convert with a reicever to ELRS and dissassembly GPS Can you help me please? Thanks
Thank you for the video, it is super clear and helpful, do you have a video for the complete setup of the GPS with the 2 other cables you mentioned it is used for the compass? and if I don't install these 2 cables will I be able to return home? or if you can share a list of features enabled after connecting the 4 cables only while keeping out the 2 other ones related to compass. Thank you so much!
THX. @XING//FPV/ I swapped to INAV. I soldered the wires but cant work. Of course I also enabled magnetometer (QMC5883) on config panel. Need remapping or anything else? When I connect to USB only the FC board now hear constant bee-beep very quiet after boot. With LIPO power the bee-beep loud and constant again , magnetometer icon is red. Pls help! I have a Blitz Mini F7 fc board.
Hi, just wondering if you can advise me on something. I bought the DJI BNF version of this drone but want to upgrade it to crossfire because I bought a tango 2 controller. My question is can the SucceX-E Mini F7 Flight Controller be used with the TBS crossfire micro receiver V2? If so how does it work, does it just plug in or need to be soldered? Thanks for any help, I'm slowly learning!
You could check the Wiring Diagram on the Google Drive and check RUclips for some help. If you're not able to, send it to one of the iFlight repair shops and they install it and do the setup
@@xingtheiflightinsider Well I would say it's already a benefit to have just a compass in the OSD as well as an arrow pointing to home. It is just two more solder pins more its not that much. ;)
@@KostasGur Yeah true it's not really needed for betaflight because it can kinda emulate the compass with GPS and gyro just like a fixed wing. But I don't like that much and started to put INAV on everything with GPS (and compass) anyways because the rescue mode on betaflight is not very reliable and does need a lot of tuning. If I dont need or want the RTH because of freestyle I can just arm the drone without GPS lock and it will drop then on failsafe like on betaflight. Or you can also use multiple profiles if you want to disable RTH for freestyle or inside buildings. ;)
@@materia79 I just received mine Evoque F5D HD 6S GPS Version with only the 4 wires connected from the factory (the last two where...missing!) and with no baro even if they had a barometer in their page when I ordered it. I am wondering how can it calculate the altitude without a barometer when you setup the GPS Rescue?
1. Not every flight controller has a Barometer installed and sometimes it's the newer DPS310 which was not supported by Betaflight before 4.3.0. 2. UBLOX
@@xingtheiflightinsider xt60 "H" plug? none of my types if xt60 connectors fit into that tail piece, which has a bar across it. i see no way to get it into that piece. do you have a picture of the plug before it is screwed in?
Why my gps keep turning red and another led on gps keep blinking green? I’d no idea to fix my gps, it cant lock any sats and detected false on betaflight
Thanks man, you are a life saver. The diagram on the iflight page was so messed, I'm glad you made this video!! Going to solder up my gps now confidently.
I’m confused, why did you not installed the SD and CL wires? And where is it located to install? Will it work fine if I don’t install those 2 wires on my Nazgul evoque f6 v2?
Can you make a video "How to configure the iFlight M8Q-5883 GPS in betaflight" ?
Is in work already
This! I placed order on this quad along with gps module but have no idea how to set it up in Betaflight 🥲 would love tutorial on this subject.
I have the Evoque F5D with the Blitz mini F7 and DJI 03 air unit, and I connected the 5v,GND,Rx,tx to plug and the SDA and SCL wires soldered, but I cannot get the gps icon to light up in betaflight. I have gps turned on for UART4 and UBLOX turned on. The gps module has steady red light with a flashing green light, any suggestions?
That's all well and good but where can I find the TPU GPS holder that will attach to the frame so that I can secure the GPS receiver to my Nazgul 5 v2?
That should be sold on the iFlight website. It's usually sold in a set and easy to install
Hi I have the same model with dji o3 system and gps, i would like to convert with a reicever to ELRS and dissassembly GPS Can you help me please? Thanks
Thank you for the video, it is super clear and helpful, do you have a video for the complete setup of the GPS with the 2 other cables you mentioned it is used for the compass? and if I don't install these 2 cables will I be able to return home? or if you can share a list of features enabled after connecting the 4 cables only while keeping out the 2 other ones related to compass. Thank you so much!
Where to solder the two free wires when I want to use compass? I have Nazgul Evoque 6 with same gps/compass module. Thank you!
The 2 wires go on SDA and SCL pads. But compass should only be necessary on an INAV build.
THX. @XING//FPV/ I swapped to INAV. I soldered the wires but cant work. Of course I also enabled magnetometer (QMC5883) on config panel. Need remapping or anything else? When I connect to USB only the FC board now hear constant bee-beep very quiet after boot. With LIPO power the bee-beep loud and constant again , magnetometer icon is red. Pls help! I have a Blitz Mini F7 fc board.
Great video. not easy to get right. Thanks
Can it be any solder pad? Or does it have to be those specific pads
Thank you so much thats what I needed !
And kow can you fix it ? 3DPRINT TPU ?
Thank you for the video!! Nicely done
Can you please tell what screws and spacer size + type is used to hold gps mount? Also is there something special in betaflight setup for gps? Thanks
Thank you for a very good explanation. do you have GPS Stl?
No sorry, please checkout the iFlight Google drive if there's one.
when usin scl and sda, what colors are correct, it says blue and grey but the remaining leads are orange and purple
Nicely done my friend 🤘🔥🔥
Thank you for the video!! 100% useful
Hi, just wondering if you can advise me on something. I bought the DJI BNF version of this drone but want to upgrade it to crossfire because I bought a tango 2 controller.
My question is can the SucceX-E Mini F7 Flight Controller be used with the TBS crossfire micro receiver V2?
If so how does it work, does it just plug in or need to be soldered?
Thanks for any help, I'm slowly learning!
You can check our wiring diagram for your specific FC on our Google drive
drive.google.com/drive/u/0/mobile/folders/1r3MNTBNYSzGeRXQg45j4IJVoW1Xjk7Y0
Is it the same for evoque F5 v2 o3?
Did you have the wiring diagram for how to install the led for Évoque ? (Or vidéo ? :) ) thanks you
All the wiring diagrams are on the iFlight Google drive, I think there's a link in the video description
Just got F5D today but my FC is a blitz mini f7 not the same how do I install GPS. Can’t get any info I am using DJI everything
You could check the Wiring Diagram on the Google Drive and check RUclips for some help. If you're not able to, send it to one of the iFlight repair shops and they install it and do the setup
hello .. why have you soldered only 4 wires to the FC ? .. there are 6 wires on the gps module
the other 2 wires are for the compass, which isn't needed for Betaflight builds anyway
@@xingtheiflightinsider Well I would say it's already a benefit to have just a compass in the OSD as well as an arrow pointing to home. It is just two more solder pins more its not that much. ;)
@@xingtheiflightinsider but If you want to change to INAV with RTH functionality you will need them I think
@@KostasGur Yeah true it's not really needed for betaflight because it can kinda emulate the compass with GPS and gyro just like a fixed wing. But I don't like that much and started to put INAV on everything with GPS (and compass) anyways because the rescue mode on betaflight is not very reliable and does need a lot of tuning. If I dont need or want the RTH because of freestyle I can just arm the drone without GPS lock and it will drop then on failsafe like on betaflight. Or you can also use multiple profiles if you want to disable RTH for freestyle or inside buildings. ;)
@@materia79 I just received mine Evoque F5D HD 6S GPS Version with only the 4 wires connected from the factory (the last two where...missing!) and with no baro even if they had a barometer in their page when I ordered it. I am wondering how can it calculate the altitude without a barometer when you setup the GPS Rescue?
1.How to activate the barometer iflight nazgul analog, I dont see on Betaflight?
2. iFlight M8Q-5883 GPS what protocol UBLOX< ENMA..?
1. Not every flight controller has a Barometer installed and sometimes it's the newer DPS310 which was not supported by Betaflight before 4.3.0.
2. UBLOX
Where did you connect SD and CL cables?
I’d like to know that too. The Succex-D Mini doesn’t have UARTS set up for that, but I guess there’s a way to set those up yourself?
I am doing a scratch build and can not find how to install the xt60 plug into the rear tpu part. could you explain how it fits in?
It's a black XT60 that gets tightened with 2 screws to the TPU
@@xingtheiflightinsider xt60 "H" plug? none of my types if xt60 connectors fit into that tail piece, which has a bar across it. i see no way to get it into that piece. do you have a picture of the plug before it is screwed in?
@@micsherwood4930 nah. Please check the iFlight website for pictures.
@@xingtheiflightinsider they dont address it,that i could find.
Why my gps keep turning red and another led on gps keep blinking green? I’d no idea to fix my gps, it cant lock any sats and detected false on betaflight
Rx and Tx wires are correctly soldered?
What uart is the gps Using ?
Did I miss something or are you just not using the CL purple wire and DA orange wire?
Not using it. It's the compass and not necessary for Betaflight basically. I wanted to keep it simple, nothing more...
how to install runcam thumb ?
How do we know it's working?
The red light on the GPS Module?
Check in betaflight configurator. Go outside with your computer and check if your module is finding sats or use your OSD and wait.
What do you think about that gps module? Is it good (like fast satellite fix)?
I heard it's not good for Europe, as it lacks that regional satellite standard. For all other regions its awesome and has a fast fix