I've developed a habit where I don't fully commit to a weld if it's something that can be welded when the project is in its completion phase. I usually just tack it in place. This has saved me a TON of time grinding/cutting if something is wrong.
@@Progeniusz muszę Cię rozczarować już takie są. To wszystko jest takie proste po obejrzeniu filmu ale 90% by na to nie wpadła chociaż wszystkie maszyny działają na identycznym schemacie
Excellent! Now make a smaller version to use as a lift on your welding table-and to turn/tilt it as well. 🤔 Looking forward to part 2. Great video-a 👍👍👍 as always. God bless.
Very satisfying to watch! Must be that AMSR thing they go on about! You have an extremely high level of knowledge and skill which you show in your videos, take care from the UK!
The advantages of the hydraulic system are , 1: it’s so powerful to move anything, close or far away. 2: one hydraulic system can operate many implements at the same time, and in different directions.
@TommyTempath it might be in the Valve Body so to say, as if I am correct that sort of dual valve body has in and return, plus the 2 sets of ports. 13:13
Wow that is amazing the last part running 2 actuators at the same time is sick if your gonna be making big bucks gonna need 1 of these wow amazing work
Super. Dla nieco większego komfortu pracy polecam silnik z pompą i wszelkie elementy podłączone z nimi stalą (np. rurami hydraulicznymi) zawsze umieszczać na tanich walcowych, metalowo-gumowych wibroizolatorach.
is the relief valve integrated in the valve block? have you consider to put a strainer inside the tank to protect gear pump? in general suction pipe seems not very wide, you could have some problems when oil is cold. good job, i hope to be helpful
Yes, the overflow valve is in the manifold. A mesh filter is also used, you will see it if you watch the video carefully. The suction pipe is not thick, but the pump is of low efficiency, so it should not be a problem, especially since the temperature in the workshop is almost always higher than 15 degrees Celsius.
This turned out very nice! The motor seems like the kind that belongs in a machine shop. How may RPM does it turn? I'd love to have one for my log splitter so I don't have to buy gas and keep a battery for it.
Cześć my friend. Thank you for this great video, I've been playing with the idea of a car elevator for months. With your setup, I have no excuses. Subscribed 😄 Respect from Romania.
Witam, bardzo dziękuję za film. Czy mógłbyś umieścić link do poszczególnych komponentów/części (adaptator obudowy silnika do pompy hydraulicznej, adapter łączący itp.), gdzie można je kupić, byłoby idealnie. Dzięki
Ein paar Tipps von einem Hydraulik Monteur Unbedingt eine maximal Druck Begrenzung in die Druckleitung einbauen um Schäden zu vermeiden Keinen Filter in die Saugleitung einbauen der Ölfilter muss in die Ölrücklaufleitung in den Tank dafür gibt es spezielle Rücklauffilter zum Einbau in den Tankdeckel
so random question, over here in america, seems like Hex Head Bolts are the way to go, but over seas it seems like Socket head bolts are the way to go. You, Workshop from scratch and Donny DIY all seem to favor socket heads, are they just more prevalent over there? is there a reason why you prefer socket head over Hex?
Przewody hyd bez oplotu w bezpośredniej ekspozycji tuż przy operatorze - czy to bezpieczne? Widziałem na jakimś szkoleniu zdjęcia człowieka któremu struga oleju z uszkodzonego przewodu wbiła się w rękę i napompowała jak balon. Ale tu pewnie ciśnienia o wiele niższe?
@@MadeinPolandChannel To już raczej wysokie ciśnienie, ale nie jestem specem - warto zapytać kogoś jak to pod kątem bhp przy tych ciśnieniach się robi. Dbamy o bezpieczeństwo autora kanału :)
Daruz bellissimo video. Mi piace che tu abbia scritto in ITALIANO. Mi auguro un giorno di incontrarti per conoscerti di persona. Ogni tuo video è fonte di ispirazione per qualcuno dei miei
Would be great for you to update this video with what you’re doing. I’m looking to make a general shop hydraulic unit with quick connect fittings to power different self made hydraulic jacks, vices, lifts, and presses from lots of spare hydraulic parts I’ve collected from the dump truck industry over the years
Very nice work! consider some of these upgrades for you fluid reservoir: Add baffles to the inside. this will help slow the fluid down giving it more time to cool and let contaminates sink to the bottom. the return line should be as far as possible from the intake for the same purposes. Also its best to have the return line slightly submerged to prevent air bubbles from forming when the fluid falls in. one more thing i might add is a magnet to catch metal particles. By the way i didn't see a pressure relief valve anywhere. it would be wise to add one especially since you will be using it as a press.
Your tips are very accurate and useful to many people. However, my hydraulic system is very simple because it will not operate under constant load and its operation will be rather temporary. Your tips are good for larger systems exposed to longer run times and higher loads. Regards.
I bought them here. From what I checked, they are available in other countries, but you have to look a bit 😉 sklepdlarolnika.pl/pl/p/Szybkozlacze-hydrauliczne-mimosrodowe-euro-gniazdo-miekkie-typu-push-G38/31141
Me encantaría aprender hacer una prensa hidráulica amigo pero no sé cómo empezar me gustaría recibir consejos para poder desarrollar una prensa para trabajar 🙏👏👏
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
I've developed a habit where I don't fully commit to a weld if it's something that can be welded when the project is in its completion phase. I usually just tack it in place. This has saved me a TON of time grinding/cutting if something is wrong.
:-) definitely throw connector of switchers, tunnel presives to asphalt. 8.
@@ArslanSattar-v5b 😂
Czy jest coś czego nie da się zbudować? Wspaniale, też bym potrzebował takiego sąsiada i przyjaciela. Wszystkiego najlepszego👍
On to pewnie by nie zbudował wszystkiego, ale jak ja zbuduje zdalnie sterowaną koparkę to już wszystko zbuduje :)
@@Progeniusz muszę Cię rozczarować już takie są. To wszystko jest takie proste po obejrzeniu filmu ale 90% by na to nie wpadła chociaż wszystkie maszyny działają na identycznym schemacie
"Measure once cut twice"....Definitely been there my friend. 😅
Cut it 3 times and it is still too short..
Nice work, that will be handy testing hydraulic parts and systems. Have a great week
add angled edges to a circle and split logs fast and easy too ... or make planks or shingles with little effort ...
I am so impressed with your work.
You are a wizard! Nice work!
Kick ass!
Great power unit. Press, crane, clamping, etc
Thanks for sharing
Cheers
Turned out nice!
Thanks 👍
Another great video! Thank you for taking time to build, film, edit and post this video.
Молодец !! Руки из плеч 👍👍👍👍👍
Very good. Please answer my questions, how many kilowatts is the electric motor? And how many liters per minute is the hydraulic pump?
Nice bro!
Thanks man 👍😉
Nice job bro 👏
Excellent! Now make a smaller version to use as a lift on your welding table-and to turn/tilt it as well. 🤔
Looking forward to part 2. Great video-a 👍👍👍 as always. God bless.
Very satisfying to watch! Must be that AMSR thing they go on about! You have an extremely high level of knowledge and skill which you show in your videos, take care from the UK!
Great work! We are a hydraulic repair shop in North America and make a lot of power units. Appreciate the content!
Thanks! 👍
Fantastic work, project, and video. Cant wait to see what you do with it, very useful. Love your creativity and craftmanship.
I liked the end result where MiP bends sections of steel. Would this size of hydraulic pump be strong enough to squash an empty 45 gallon/205L drum?
The advantages of the hydraulic system are , 1: it’s so powerful to move anything, close or far away. 2: one hydraulic system can operate many implements at the same time, and in different directions.
Cześć, ile obrotów/min silnik ? I czy to jakiś gotowy zestaw z tą przystawką do pompy ?
1440, zestaw kompletowany, składany z poszczególnych części, (sprzęgło kłowe, dzwon pompy hydraulicznej, pompa i silnik.
Ile to ma ton nacisku?
Rębak do drewna z tego można zrobić?
MUITO BEM BOLADO ...COM TODA SUA EXPERIÊNCIA ..TODOS OS PROJETOS SÃO FENOMENAIS ,,,,JAÚ SP BRAZIL 😊
I may have missed it but does this system have a pressure relief valve to drain back to tank?
@TommyTempath it might be in the Valve Body so to say, as if I am correct that sort of dual valve body has in and return, plus the 2 sets of ports. 13:13
Wow that is amazing the last part running 2 actuators at the same time is sick if your gonna be making big bucks gonna need 1 of these wow amazing work
Fajna pompka. Do rębaka powinna się nadać, jak myślisz? Trochę wolno by to chodziło tylko.
Do łupania trochę za wolną, chyba że ktoś dysponuje sporą ilością wolnego czasu 😉
I'm from ethiopia I liked your profession. Please work on the piston type system, I want to know
Super. Dla nieco większego komfortu pracy polecam silnik z pompą i wszelkie elementy podłączone z nimi stalą (np. rurami hydraulicznymi) zawsze umieszczać na tanich walcowych, metalowo-gumowych wibroizolatorach.
is the relief valve integrated in the valve block? have you consider to put a strainer inside the tank to protect gear pump? in general suction pipe seems not very wide, you could have some problems when oil is cold. good job, i hope to be helpful
Yes, the overflow valve is in the manifold.
A mesh filter is also used, you will see it if you watch the video carefully.
The suction pipe is not thick, but the pump is of low efficiency, so it should not be a problem, especially since the temperature in the workshop is almost always higher than 15 degrees Celsius.
@@MadeinPolandChannel ok, i missed the mesh, good job!
Small question is the pump designed for that much rpm or does it have a short duty life ?
MM77 Approved 👍🏼👍🏼
Parabéns pelo seu grande projeto incrível muito bom mesmo
Where did the bell housing and coupler come from? Looks like it’s all meant to be put together
You can configure the engine, bell and pump online. It's not difficult, you just need to spend some time.
Thanks. Where does it come from?
Классно! Только бы ещё увидеть как отключаешь от системы и сливаешь масло из цилиндра.
А зачем из них сливать масло?
@@mechnomad2572 для подключения к другим целиндрам при необходимости, например. Иначе зачем там быстросъемы?
Masz fajne pomysły albo ciekawe zlecenia. Niektóre pomysły zamierzam wykorzystać. Dzięki.
Your work is mind blowing 😊😊😊😊😊😮😮😮😮😮😮😮😮❤❤❤
Can't wait for the next part, those hydraulics are working nice! 👍💪✌
Cudowna sprawa!
Love you man,great work😊
Buen trabajo una consulta cuanto de precion ejerce quisiera mover un motor hidráulico
Jeśli można wiedzieć to jakie ciśnienie i jaki przepływ ma ta pompa ? Silnik malutki.
Fantastic work, dude! Really well done! 😃
I bet it's going to be really useful!
Stay safe there with your family! 🖖😊
0:05 hallo, kannst du noch eine Auflistung erstellen wo man die Verschiedene Teile kaufen kann?
Thanks for the video!
Refreshing our memories!
Nicely presented!
Witam Darku siłę robi większy siłownik przy tym samym zasilaczu ( Podobny projekt kończę ) Pozdrawiam
Tak dokładnie. Prędkość się zmniejsza, ale siła rośnie.
Pozdrawiam serdecznie 😉
@@MadeinPolandChannel Tak jest jak napisałeś
You are wise beyond your years!!
Great project. Tell me, what kind of marker with a thin rod do you use for marking on metal?
LYRA 4480051 Marker for deep holes 😉
@@MadeinPolandChannel thank you!
Welcome to the hydraulic press channel. Great build
Or maybe welding table press channel 😂
This turned out very nice! The motor seems like the kind that belongs in a machine shop. How may RPM does it turn?
I'd love to have one for my log splitter so I don't have to buy gas and keep a battery for it.
Amazing job my friend congratulations
Thank you! Cheers!
Po zrobieniu agregatu, w układzie sterownik dwustronnego działania coś harczy jakby w siłowniku, Jaka może być przyczyna?
Proszę o podpowiedź
Kosmos robota !❤
Wow, an amazing work! 👍
Хорошо работать, когда все детали имеются 👍
Cześć my friend. Thank you for this great video, I've been playing with the idea of a car elevator for months. With your setup, I have no excuses. Subscribed 😄
Respect from Romania.
Fajnie wyszlo, jak zawsze, mega sprzęcik i super film, pozdrawiam
Witam, bardzo dziękuję za film. Czy mógłbyś umieścić link do poszczególnych komponentów/części (adaptator obudowy silnika do pompy hydraulicznej, adapter łączący itp.), gdzie można je kupić, byłoby idealnie. Dzięki
Love from❤ 🇮🇳india🙏🙏
Ein paar Tipps von einem Hydraulik Monteur
Unbedingt eine maximal Druck Begrenzung in die Druckleitung einbauen um Schäden zu vermeiden
Keinen Filter in die Saugleitung einbauen der Ölfilter muss in die Ölrücklaufleitung in den Tank dafür gibt es spezielle Rücklauffilter zum Einbau in den Tankdeckel
As always, well done!
Can you please tell me what is the make and model of the tapping head you are using? Thank you.
King Tony 39123012M
@@MadeinPolandChannel thank you.
Jest moc. Będzie ładna giętarka. a może jeszcze giętarka do rur ?
Zobaczymy co czas przyniesie 😉
so random question, over here in america, seems like Hex Head Bolts are the way to go, but over seas it seems like Socket head bolts are the way to go. You, Workshop from scratch and Donny DIY all seem to favor socket heads, are they just more prevalent over there? is there a reason why you prefer socket head over Hex?
I have better access to socked hed in hard-to-reach places 😉
Siemanko nie wiem czy bylo, może wykrawarkę do otworów byś zrobił. Pozdrawiam!
Excelente video, todo muy claro. 👍🇲🇽
Po co są te otworki w nakrętkach/złączkach? To jakaś "kontrola" szczelności?
It turned out awesome; did I see a leatherman charge tti+ being used?
Yes Sir. Great for everyday work.
Skad wziac taka przystawke by połączyć silnik z pompą?
Poszukaj pod nazwą "dzwon pompy hydraulicznej"
@@MadeinPolandChannel dzięki wielkie 👍pozdrawiam
Muito bom ! Tem como passar , o modelo da bomba é a capacidade do motor? .
To teraz czekam na prasę 😂😂
Great my bro, please can you tell me the type (serial number) of blade that you used. Thanks in advance.
Zrób jakiś domowy podnosik taki ala paleciak tylko żeby podnosił na większą wysokość i żeby można było podnosić i opuszczać wkrętarką 😎
Albo połączenie paleciaka z rowerem, aby nie targać jak jest załadowane dużo. Podnoszenie też realizowane nożnie.
Is that a tapping head on your hand drill? Could you give us details?
Przewody hyd bez oplotu w bezpośredniej ekspozycji tuż przy operatorze - czy to bezpieczne? Widziałem na jakimś szkoleniu zdjęcia człowieka któremu struga oleju z uszkodzonego przewodu wbiła się w rękę i napompowała jak balon. Ale tu pewnie ciśnienia o wiele niższe?
Dodatkowe zabezpieczenie na pewno nie zaszkodzi, ale u mnie ciśnienie jest max 180 barów, a węże są do bodajże 225 😉
@@MadeinPolandChannel To już raczej wysokie ciśnienie, ale nie jestem specem - warto zapytać kogoś jak to pod kątem bhp przy tych ciśnieniach się robi. Dbamy o bezpieczeństwo autora kanału :)
ten stół spawalniczy to nie traci jakiejś precyzji przy takich zabawach?
Blat 16 mm I Kratownica pod stołem robi robotę 👍
Nice, next big Project... Building your own excavator💪
Great work and great skills!
What's the rated pressure for the pump?
I think 250 bar, but the overflow valve on the hydraulic distributor is set to 180
@@MadeinPolandChannel Thanks! Keep up the good work! I always enjoy your videos!
Name of the parts which will be useful for the beginner's
What bandsaw you using? Is it worth the money?
Nice one ! Can't wait to see the next videos !
Здравствуйте! Отлично сделано! Подскажите, а что за патрон куда крепите метчик?
Daruz bellissimo video. Mi piace che tu abbia scritto in ITALIANO. Mi auguro un giorno di incontrarti per conoscerti di persona. Ogni tuo video è fonte di ispirazione per qualcuno dei miei
Appreciate for better workmanship & your skills. I would like to see more videos going to be made by you.
Hydraulics and Electricity are “IDENTICAL “ .
How many tones does it hold?
Good tool to have.......enjoyed that - thanx
very good job one like 👍
Great work you are awesome bro 👏 😊❤❤
Would be great for you to update this video with what you’re doing. I’m looking to make a general shop hydraulic unit with quick connect fittings to power different self made hydraulic jacks, vices, lifts, and presses from lots of spare hydraulic parts I’ve collected from the dump truck industry over the years
Very nice work! consider some of these upgrades for you fluid reservoir: Add baffles to the inside. this will help slow the fluid down giving it more time to cool and let contaminates sink to the bottom. the return line should be as far as possible from the intake for the same purposes. Also its best to have the return line slightly submerged to prevent air bubbles from forming when the fluid falls in. one more thing i might add is a magnet to catch metal particles. By the way i didn't see a pressure relief valve anywhere. it would be wise to add one especially since you will be using it as a press.
Your tips are very accurate and useful to many people. However, my hydraulic system is very simple because it will not operate under constant load and its operation will be rather temporary.
Your tips are good for larger systems exposed to longer run times and higher loads.
Regards.
Very good advice
Excelente trabajo!!
OMG! Where did you get these offset adapters for your couplings? These are genius! 🤩
I bought them here. From what I checked, they are available in other countries, but you have to look a bit 😉
sklepdlarolnika.pl/pl/p/Szybkozlacze-hydrauliczne-mimosrodowe-euro-gniazdo-miekkie-typu-push-G38/31141
Gracias por el enlace ,y buen trabajo
Thank you for the dark filter when you were welding
Fantastic work here!
What would you call the piece that enclosed the motor to pump mating? The shroud type price.
pump bell housing ;)
Impressive guy....
Masz jakiś pomysł jak zrobić redukcję z silnika 125 quad na napęd tak żeby jak najwięcej miało to siły
Najprościej redukcję na zębatkach.
@@MadeinPolandChannel czyli 4 zębatki mała duża koło niej mała i dalej na dużą takie coś ogarnie czy są jakieś ślimakowe redukcję
Hallo,
Was ist das für ein Bohrfutter das du für die Gewindeschneider verwendest?
Приветствую, подскажите пожалуйста какие характеристики электродвигателя?
Me encantaría aprender hacer una prensa hidráulica amigo pero no sé cómo empezar me gustaría recibir consejos para poder desarrollar una prensa para trabajar 🙏👏👏
A quanti BAR hai impostato la pressione quando sei sotto sforzo?
180 BAR