As a grown man child, I seriously would’ve gotten one of theses years ago for my work bench but the 143,345,583 videos showing how hard they are to start really doesnt make it worth the mail mans time.
No, These ones run great, I have one , the rotarys are pain... They wont Run well ore even start. In the Manuel stands how to tune them. The screw for the fuel mixture has to Go all the way in, one and a half Turn Back and it will start, than you can adjusg the idlespeed. After that you Rev the engine, if it revs Up slowly only, than it is to rich, turn the mixture screw out Just a tiny bit. If the engine revs Up but the idlespeed stais Up quiet a Long Time than it Runs to lean. Screw the mixture screw in Just a tiny Bit. The V8 Models Run very wenn and arent hard to tune.
I think its already been mentioned but u need to run the vent line to fuel tank to pressurize it so it pushes fuel to the carbs. It was already running lean and then u sprayed it with nitrous which leaned it out even more. Poor thing didnt stand a chance! Would love to see it in the truck once u get it running right. The extra wieght in the front would be beneficial to a burnout rig imho.
He even knew that you need to run it rich with nitrous since you have 2 oxygen molecules instead of the normal 1 with air you have upto twice the fuel burning power with nitrous.
I'm a former mechanic, and electrician. You need to be careful when taking the cambelt off, the timing might be out,- which might be one reason it doesn't run properly. There should be an idle screw on the carburettor- this allows you to set the idle once it is running. It looks like you need to take it apart
I'm a mechanical engineer, the metal dust in the oil tells me he fucked it 😂 Nitro fuel has a mixture which also contains oil, it's similar to fuel mixed for 2 stroke engines, a little oil that lubricates the engine and gets burned. When kev ran it on 100% methanol, it flushed out all the oil and it was basically metal on metal. I honestly sometimes wonder why kev makes stupid decisions when it comes to his videos sometimes. He didn't even run the engine in properly, he never runs his rc car engines in. Just starts them and full throttles. It's sad to watch, but i guess it gets him the views. Same when he sends the cars into oblivion and damages half the parts, but you can can argue that's part of using them, to bash, break, fix, repeat.
the methanol fuel wouldn’t hv caused the engine to seize that quickly. Theses engines are built to last a few months…. i doubt a cycle of 30 mins of non lubricated rpm ruined it. I think it’s due to the change in temperatures as he ran the fuel. The only reason i can think of that his shaft was stiff was cuz he ran the engine way too hot. The radiator had no fan on it and there was no where near enough air going into the supercharger in the first place. I strongly believe his engine seized up due to incomplete combustion and thermal expansion.
Try pouring all the oil out of you're car engine and see how meny seconds before it seize. 2t engines get lube from the oil mixture in the petrol.. methanol is alcohol that cleans the engine really well from all oil residue xD@@KS-vo3hf
And he didn’t even have the thing running correctly (which he could have, because they do run) before he added upgrades. He went about it the wrong way and destroyed the $2100 engine. Just for content. Must be nice.
Methanol killed it! It's not got any oil in it! But why didn't you connect the crankcase breather back to the fuel tank which would have pressurised the tank acting like a fuel pump.
That messy Port was a line to pressurize the fuel tank. That poor thing never got enough fuel to run nice. You should rebuild it, and definitely run it in a burnout rc project!!
Hey Kevin, those glow starters have a “potentiometer” in them. I was gifted a 2 cylinder engine and the glow starters wouldn’t make the glow plugs glow. I adjusted the little screw on the potentiometer to get them to glow on a 2S Lipo. The glow starters are also very finicky and you can burn out the plugs super easily. It’s a bad design.
First mistake, using water as coolant. Second mistake, using non nitro fuel in it, third mistake trying to use nos, your lucky this little thing did not explode sending shrapnel in your face. When the coolant line blew nitro onto you telling you the head gasket was blown already mixing nitro into your water before the water boiled blowing the coolant line onto you, also its a bit above my head but i would think you would need to change the timing if you use non nitro fuel or nos, i would not recommend nos, its an aluminum engine and i know real aluminum engines cant handle nos, i would not expect this little guy to handle it even if it was steel. Awesome video dude, dont underestimate these little engines, they can throw a rod through their little oil pans and blocks like a real engine. Id also reccomend safty glasses at least, i dont think you want nitro/nos/fuel/oil in or shrapnel in your eyes.
Yes it was thoughtful but we Colonists aren't that dumb. I would hazard a guess that most 'Muricans here watching Kev are the type of people that watched UK Top Gear. The real TG, with Jeremy, Richard and James. So.. petrol, bonnet, boot, ashfelt, etc.. we're familiar, yes. Except for when these Brits speak of a measuring unit called.. Kilo-Metres. I have no earthly idea what those are.
Hello. This type of V8 engine also needs regular oil, because you put the factory oil in it, but it is not enough to keep the engine running. The engine was full of metal particles because you boiled the cylinders. Before starting for the first time, you have to put a little normal oil in it.
i saw at the back a gear sticking out and the thing that fell of was supposed to turn it. i think it is the oil pump and it was not turning at 6:49. it probably never turned after that and that would also explain the metal bits and the seized engine.
@@reneentarastraathofvanmarw2287 u mean in the back where the flywheel sits, with that big gear? i dont think its supposed to be turning while the engine is running. theres a starter on it with a small gear and since it cant disengage like on a real car, it probably can only turn in one direction while trying to start it. but not 100% sure.
@@reneentarastraathofvanmarw2287 The big wheel at the back is the flywheel that connects to the starter, and what flew off was the clutch housing. The oil pump is always located on the crankshaft at the first cylinder so that its speed matches the engine speed
When i was a kid, i found one of those silver nitrous oxide systems in my mums knicker drawer, always wondered what it was for, I never knew she had a interest in RC though.
anyone that knows how glo engines actually run, and how the compression and fuel ratios affect ignition timing also knows that a supercharger on a glo engine is sheer stupidity.
@@paradiselost9946 It's interesting that every single one of these little V8 engines end the same way and they all used the glow plugs...The only ones I've seen run almost reliably are with the spark plug ignitions systems...He might need something a little bigger than that Arma to fit everything into it.
@@BlackTownie999 Runnin methanol will make it waaay harder compared to usin plugs and gas. I’m sure those carbs start freezin up and they definitely aren’t made for much more then being mounted on a block or something and just starting it and showing your friends type deal and not for runnin in a rc and I feel that’s why there ain’t alot of dudes tryin it, absolutely badass tho and I’m extremely jealous 🤠
yea but if it gets too big it gets too heavy too. these engines dont produce enough torque to be used in rc cars that it would make fun. i like them, how they look, sound and how tiny it is and yet it works. but for a real use he would need a gearbox just like johnnyQ90 has build. there was a dude who build a 1/4th Grave Digger from scratch, he used a stinger v8 engine which was compared to this one bigger, but it did function way better.
I Know this sort of thing can be frustrating. But from what you said it was lean and you were venting pressure from the crank case to atmosphere instead of the fuel tank and throwing a dense oxygen charge at it to boot. These engines have been proven to work and work well. I would love to see your project! But at least give the engine a chance.Love the content.I was just hoping for more. The arm chair know it all LOL!
I was thinking it made sense to run the hose from the "crank case" to the tank for positive pressure. I've never played with one of these myself but I was just thinking something was off.
before you add nitrous to ANY engine i recommend you do some research... NO2 should only be added at wide open throttle, otherwise detonation murders the cylinders, at least in regular automotive applications. you basically threw a bomb in the intake, and not in a good way. this is a cool project, i understand you're having fun, but frustration usually comes from ignorance. cheers!
I would definitely like to see this as a project. I had multiple electric RC cars but I’ve never wanted to mess with gas because I know they’re pretty difficult and nitrous is definitely not something I feel comfortable playing around with.
That line that was spraying nitro, you should attach it to the top of the Fuel tank. I remember my older nitro cars had a tube that went from the exhaust pipe to the top of the fuel tank. I'm pretty sure that's why you were lacking fuel pressure to feed the motor. Best of luck!!
Hell yes, I personally would love to see a supercharged Toyan V8 put into a Infraction. If you do you gotta make dual exhaust that exit the rear. Lmfao. The guys over at Warped Perception had some pretty good luck with this motor. I'm willing to bet they can help you out with running it. I think they actually ran different types of fuels through it as well to find what gave the most power.
Kev Love the content, I love how you cater to us Americans by using “our” terms. One term that should never be used by either side of the Atlantic is “NOSS” It’s called Nitrous brother Well done sir
It's a novelty engine... It is not made to run long or last long... There is a reason you can't find videos of these toyan engines doing anything except free revving by youtubers who were given free samples to make a video on... they only make a couple videos because the engine stinks and only runs a few times. A single cylinder nitro engine is 100x better. This engine is a waste of time.
@@volvo09 Kev has done it before and he can do it again Also if you truly believe this is a waste of time how come you clicked on this video and looked at the comments?
@@Alvino_rc i don't doubt his skills - that's why I love his channel, but I'm calling the engine a waste of time because it won't last... I know people WANT to see it done, but it's not going to end up the way everyone expects (some V8 rocket)... It has nothing to do with Kevin and only the motor. It makes nothing for power, and is made of soft aluminum, it just won't last and a cheap nitro engine will kill it all around. Will it make a great video? Probably. But will it last more than a few tanks of fuel before the valvetrain is worn out and it won't start anymore? I highly doubt it.
Yes but a mid mounted engine will hold a drift better and be alot easier to control. I've owned many cars in my 50 yrs as a semi-pro and mid mounted is definitely the way to go in a lightweight body.
@@dazofthemoo1531 It's a tall engine in a model, it'll probably want to wheel stand everywhere. I suppose it wouldn't if he uses hard, smooth type tyres but, then it would just skate around boringly. I had a 1/5th Baja bug with the 26cc engine and yeah, that drifted ok mostly at speed with a mid to rear kind of mounting but this is much shorter wheel based and that tall engine I think will probably be pretty prone to rolling too but, it'll be a bit of a hoot either way, especially if he gets it running a lot better than here. It never even revved very well so was pointless adding nitrous, damage, probably from being too lean and consequently no lube looks like it may have already done some major damage to it. I think the nitrous attempt on a glow engine without running in and proper tuning was a very bad idea.
@@lorditsprobingtime6668Yes. Considering the cash Kev seems to have behind him, he's probably better binning that one and starting again. Once he gets this thing going, I think it's going to be either very good or very bad. I'm definitely curious to find out.
@@dazofthemoo1531 I wouldn't ever bother with one at the prices they ask but, most sensible people who've spent the money to get one will make sure they've got that pressure to the fuel tank and run it very rich and slowly start leaning it out bit by bit after several tanks full. I've seen enough running on YT to know they can really scream and do sound pretty amazing. This was not the way to do it and then shoving nitrous into it when already running lean was a very smooth brain thing to do. I would really love to hear it running properly and in a model of some sort, it should look and sound amazing, IF he doesn't screw it up like here, what a waste!
The idea is really cool, but i'd try without nitro injection, or even without the supercharger at first since that makes it harder to start. And idk if it would work well in an infraction, it would be very front heavy. Maybe put it mid mounted in a limitless so you have better weight distribution?
Welcome to methanol/ nos style engines or just big power race stuff, people build 80,000$ engines and burn them down on the dyno when breaking them in, before even getting to take it too the street or drop it into a car lol. Trust me, I been there unfortunately 🤦♂️🤠
For $2000 I would expect it to work. Make the manufacturers get you another one. Doesn't look good if it doesn't run. Would be amazing if it ran in that truck. Keep at it !!
The meth flow rate for stoich is higher compared to nitro “blend”. Would probably need more than vacuum feed ….Also running non oil added fuel probably quickly washed the walls and cooked a bearing 😂 but love the content!!
Hey Kevin, another great vid. I love your builds and the fact that you do some of the most one and off unique projects, but sometimes it seems like you either abandon them or just don't update them anymore. I know you probably have 100000 of videos to create, but sometimes it sucks watching a really cool build and then never seeing it on the channel again.... Mp10t and the other mp10's never got more running footage :/
JONNYQ90 Said in one of his videos the supercharger rotors dont have proper clearanceing and i think thats why it would cut out and die while high reving. They will idle all day but he came to the conclusion that the supercharger is more cosmetic than actually a proper charger that makes boost. In the video while your reving the engine you can hear the rotors hitting each other. Remove supercharger then try the spray.
V8 powered RC truck?? Yes please! After everything else you've done, i know you (likely) have the know how. And i say this as a not-professional motor tinkerer, but maybe a gasoline conversion would make it easier to get a handle on. Just my armchair opinion. Good luck Kev!!
Isn't that the pinnacle of RC?... I mean, to have as much realism in at smaller scale that you may never experience in something full scale is my main attraction to models and RC. Just saying
Hey Kev, by running on pure methanol you've run it without any lubrication. Model fuel has oil and methanol for this reason. I suspect you have lunched it, but I'm more than happy to tear it down and take look if you want?
It's be really cool if you could get this to work. I would recommend sending the dead engine to "I do cars" so he can give it a proper teardown on RUclips, assuming the manufacturer won't accept it as a return.
This is like Linus Tech Tips. Hurts me to see as a mechanical engineer and former master tech. Also your American water accent is wrong and iced tea is the best tea.
🚗Win one of my cars raffall.com/kevin_talbot
I don't even have a credit card😂
I was the first to like this comment
What about the crawler that should have had the real engine too?
Can you give me a link for the nitro system :)
Looks like it might be a good candidate for a Losi MT TLR rolling chassis…?
Never would have thought that those little engines are $2100. Mind blowing.
You Shouf put it in the infra Timon of the felony
Should
Yea at that point just buy a full size engine to build lol
Hard to make, so you're basically paying for labor and fabrication
Bro you can buy an actual full size engine for that much
As a grown man child, I seriously would’ve gotten one of theses years ago for my work bench but the 143,345,583 videos showing how hard they are to start really doesnt make it worth the mail mans time.
Agreed seems like a cool project but not worth the pain
Just saw the price! I'll take basically anything 5th scale instead please
Only like 4 people who have those engines working.
It’s a total novelty, I would never pay good money for one, and I would never expect it to last.
No, These ones run great, I have one , the rotarys are pain... They wont Run well ore even start. In the Manuel stands how to tune them. The screw for the fuel mixture has to Go all the way in, one and a half Turn Back and it will start, than you can adjusg the idlespeed. After that you Rev the engine, if it revs Up slowly only, than it is to rich, turn the mixture screw out Just a tiny bit. If the engine revs Up but the idlespeed stais Up quiet a Long Time than it Runs to lean. Screw the mixture screw in Just a tiny Bit. The V8 Models Run very wenn and arent hard to tune.
I think its already been mentioned but u need to run the vent line to fuel tank to pressurize it so it pushes fuel to the carbs. It was already running lean and then u sprayed it with nitrous which leaned it out even more. Poor thing didnt stand a chance! Would love to see it in the truck once u get it running right. The extra wieght in the front would be beneficial to a burnout rig imho.
He even knew that you need to run it rich with nitrous since you have 2 oxygen molecules instead of the normal 1 with air you have upto twice the fuel burning power with nitrous.
I'm a former mechanic, and electrician. You need to be careful when taking the cambelt off, the timing might be out,- which might be one reason it doesn't run properly. There should be an idle screw on the carburettor- this allows you to set the idle once it is running. It looks like you need to take it apart
I'm a mechanical engineer, the metal dust in the oil tells me he fucked it 😂
Nitro fuel has a mixture which also contains oil, it's similar to fuel mixed for 2 stroke engines, a little oil that lubricates the engine and gets burned. When kev ran it on 100% methanol, it flushed out all the oil and it was basically metal on metal. I honestly sometimes wonder why kev makes stupid decisions when it comes to his videos sometimes. He didn't even run the engine in properly, he never runs his rc car engines in. Just starts them and full throttles. It's sad to watch, but i guess it gets him the views. Same when he sends the cars into oblivion and damages half the parts, but you can can argue that's part of using them, to bash, break, fix, repeat.
Yep, destroyed it by switching fuel. Also a mechanical engineer and former master tech.@@EagleFPV43
the methanol fuel wouldn’t hv caused the engine to seize that quickly. Theses engines are built to last a few months…. i doubt a cycle of 30 mins of non lubricated rpm ruined it. I think it’s due to the change in temperatures as he ran the fuel. The only reason i can think of that his shaft was stiff was cuz he ran the engine way too hot. The radiator had no fan on it and there was no where near enough air going into the supercharger in the first place.
I strongly believe his engine seized up due to incomplete combustion and thermal expansion.
Could have been why it sounded a little clunky
Try pouring all the oil out of you're car engine and see how meny seconds before it seize. 2t engines get lube from the oil mixture in the petrol.. methanol is alcohol that cleans the engine really well from all oil residue xD@@KS-vo3hf
Love the part when the engine got installed
To be fair the title is "can I" not "I put"
And he didn’t even have the thing running correctly (which he could have, because they do run) before he added upgrades. He went about it the wrong way and destroyed the $2100 engine.
Just for content. Must be nice.
Methanol killed it! It's not got any oil in it! But why didn't you connect the crankcase breather back to the fuel tank which would have pressurised the tank acting like a fuel pump.
Thats why it kept shutting off it didn't have pressure of the engine to feed it what it needed when needed it
@@Mike-vs9vo exactly
I didn’t even think about that,hell yeah that was his issue because he does t have a fuel pump!
cuz this guy has no idea what he's doing. Money can't buy knowledge.
That messy Port was a line to pressurize the fuel tank. That poor thing never got enough fuel to run nice. You should rebuild it, and definitely run it in a burnout rc project!!
Hey Kevin, those glow starters have a “potentiometer” in them. I was gifted a 2 cylinder engine and the glow starters wouldn’t make the glow plugs glow. I adjusted the little screw on the potentiometer to get them to glow on a 2S Lipo. The glow starters are also very finicky and you can burn out the plugs super easily. It’s a bad design.
Yes, you should do it as a project. That’ll be so awesome.
First mistake, using water as coolant. Second mistake, using non nitro fuel in it, third mistake trying to use nos, your lucky this little thing did not explode sending shrapnel in your face. When the coolant line blew nitro onto you telling you the head gasket was blown already mixing nitro into your water before the water boiled blowing the coolant line onto you, also its a bit above my head but i would think you would need to change the timing if you use non nitro fuel or nos, i would not recommend nos, its an aluminum engine and i know real aluminum engines cant handle nos, i would not expect this little guy to handle it even if it was steel. Awesome video dude, dont underestimate these little engines, they can throw a rod through their little oil pans and blocks like a real engine. Id also reccomend safty glasses at least, i dont think you want nitro/nos/fuel/oil in or shrapnel in your eyes.
I love the new Bi-Lingual format ! Very thoughtful 🤣😅=))
Same that was cool
Yes it was thoughtful but we Colonists aren't that dumb. I would hazard a guess that most 'Muricans here watching Kev are the type of people that watched UK Top Gear. The real TG, with Jeremy, Richard and James. So.. petrol, bonnet, boot, ashfelt, etc.. we're familiar, yes. Except for when these Brits speak of a measuring unit called.. Kilo-Metres. I have no earthly idea what those are.
Hello. This type of V8 engine also needs regular oil, because you put the factory oil in it, but it is not enough to keep the engine running. The engine was full of metal particles because you boiled the cylinders. Before starting for the first time, you have to put a little normal oil in it.
I was worried about it seizing up when he said he was going with pure methanol. It def doesn't have any oil mixture for lubrication.
if i remember correctly u also have to break it in and after running for a bit change the oil 1 or 2 times. before going complete bonkers with it.
i saw at the back a gear sticking out and the thing that fell of was supposed to turn it. i think it is the oil pump and it was not turning at 6:49. it probably never turned after that and that would also explain the metal bits and the seized engine.
@@reneentarastraathofvanmarw2287 u mean in the back where the flywheel sits, with that big gear? i dont think its supposed to be turning while the engine is running. theres a starter on it with a small gear and since it cant disengage like on a real car, it probably can only turn in one direction while trying to start it. but not 100% sure.
@@reneentarastraathofvanmarw2287
The big wheel at the back is the flywheel that connects to the starter, and what flew off was the clutch housing. The oil pump is always located on the crankshaft at the first cylinder so that its speed matches the engine speed
I would love to see this project come to life! Please do it Kev.
Yes
yes! flood this comment with likes!
Gotta make it happened!
Yes
do it kev
When i was a kid, i found one of those silver nitrous oxide systems in my mums knicker drawer, always wondered what it was for, I never knew she had a interest in RC though.
😂😂😂
What were you looking for when you found the nitrous canister in your mums knicker drawer?
This engines are a pain in the ass to work with, I've never seen a video where the guy starts it without losing some hair in the process
Did I just watch 2 guys blowup a $2100 micro V8?
Yes yes you did😂
$2600!
Just hook the belt to an electric motor and let it spin the supercharger pulley. These engines are notoriously hard to get to run right.
anyone that knows how glo engines actually run, and how the compression and fuel ratios affect ignition timing also knows that a supercharger on a glo engine is sheer stupidity.
It's not a 2 stroke glow engine.@@paradiselost9946
@@paradiselost9946 It's interesting that every single one of these little V8 engines end the same way and they all used the glow plugs...The only ones I've seen run almost reliably are with the spark plug ignitions systems...He might need something a little bigger than that Arma to fit everything into it.
@@BlackTownie999
Runnin methanol will make it waaay harder compared to usin plugs and gas. I’m sure those carbs start freezin up and they definitely aren’t made for much more then being mounted on a block or something and just starting it and showing your friends type deal and not for runnin in a rc and I feel that’s why there ain’t alot of dudes tryin it, absolutely badass tho and I’m extremely jealous 🤠
yea but if it gets too big it gets too heavy too. these engines dont produce enough torque to be used in rc cars that it would make fun. i like them, how they look, sound and how tiny it is and yet it works. but for a real use he would need a gearbox just like johnnyQ90 has build. there was a dude who build a 1/4th Grave Digger from scratch, he used a stinger v8 engine which was compared to this one bigger, but it did function way better.
I Know this sort of thing can be frustrating. But from what you said it was lean and you were venting pressure from the crank case to atmosphere instead of the fuel tank and throwing a dense oxygen charge at it to boot. These engines have been proven to work and work well. I would love to see your project! But at least give the engine a chance.Love the content.I was just hoping for more.
The arm chair know it all LOL!
I was thinking it made sense to run the hose from the "crank case" to the tank for positive pressure. I've never played with one of these myself but I was just thinking something was off.
The fact you said that at the end, makes you not an armchair expert/ computer expert lol, guys like that would never admit that ever 🤠
before you add nitrous to ANY engine i recommend you do some research... NO2 should only be added at wide open throttle, otherwise detonation murders the cylinders, at least in regular automotive applications. you basically threw a bomb in the intake, and not in a good way. this is a cool project, i understand you're having fun, but frustration usually comes from ignorance. cheers!
Oh yeah big block infraction 🤩
Rock on dude 🤟🏼😎
I think you need to put that engine in, it would be so cool to see!
I would definitely like to see this as a project. I had multiple electric RC cars but I’ve never wanted to mess with gas because I know they’re pretty difficult and nitrous is definitely not something I feel comfortable playing around with.
Nitro RC cars are very simple to run, The engine kevin has her is a very expensive bit of kit which very few rc enthusiasts will ever own.
That line that was spraying nitro, you should attach it to the top of the Fuel tank. I remember my older nitro cars had a tube that went from the exhaust pipe to the top of the fuel tank. I'm pretty sure that's why you were lacking fuel pressure to feed the motor.
Best of luck!!
We’re all still waiting for the one you were putting in a crawler 4 yrs ago 😂
Yup
Yeah Kev where is it
In my 43 years as an American, I've never heard any American say "water" like that.
definitely want to see this project happen
Heck yes! Please turn this into a awesome project. Go Kev!
If any body can get it done it’s you Kevin!!! 👍
You definitely should keep trying to get it running, it sounds awesome when it's going.
Absolutely make that happen we're here for it
Love your vids always so interesting and entertaining. And no unnecessary waste of time. Good work.
Hell yes, I personally would love to see a supercharged Toyan V8 put into a Infraction. If you do you gotta make dual exhaust that exit the rear. Lmfao. The guys over at Warped Perception had some pretty good luck with this motor. I'm willing to bet they can help you out with running it. I think they actually ran different types of fuels through it as well to find what gave the most power.
WaZz up, kool idea make it a series
I’m gonna love this series! ❤
About time. An Aussie burnout car.👍👍👍
Kev
Love the content, I love how you cater to us Americans by using “our” terms.
One term that should never be used by either side of the Atlantic is
“NOSS”
It’s called Nitrous brother
Well done sir
I love how kev always converts it to the american standered for us americans 🤣
KEV (no hate) please! Please! don’t let this become a project that sits on the shelf! I would absolutely love to see this ripping around a car park!❤❤
It's a novelty engine... It is not made to run long or last long...
There is a reason you can't find videos of these toyan engines doing anything except free revving by youtubers who were given free samples to make a video on... they only make a couple videos because the engine stinks and only runs a few times. A single cylinder nitro engine is 100x better.
This engine is a waste of time.
@@volvo09 Kev has done it before and he can do it again
Also if you truly believe this is a waste of time how come you clicked on this video and looked at the comments?
@@Alvino_rc i don't doubt his skills - that's why I love his channel, but I'm calling the engine a waste of time because it won't last...
I know people WANT to see it done, but it's not going to end up the way everyone expects (some V8 rocket)... It has nothing to do with Kevin and only the motor. It makes nothing for power, and is made of soft aluminum, it just won't last and a cheap nitro engine will kill it all around.
Will it make a great video? Probably. But will it last more than a few tanks of fuel before the valvetrain is worn out and it won't start anymore? I highly doubt it.
That is the coolest looking rc engine I ever seen! That would be kick ass if you install that engine in that truck!! Insane!
I would love to see this project continue!
We really want to see this come to life!!!
That Methanol had no oil in it like the glow fuel does
Yes it's probably run a bearing or worse!
Glow fuel contains oil to lubricate the engine.
Running straight methanol will kill it for sure.😢
You should mount the engine behind the cab for a mid-engine layout.
He wants a drift car, not a race car. Front mounted means not so much power needed and less tendency to wheel stand and flip.
Yes but a mid mounted engine will hold a drift better and be alot easier to control. I've owned many cars in my 50 yrs as a semi-pro and mid mounted is definitely the way to go in a lightweight body.
@@dazofthemoo1531 It's a tall engine in a model, it'll probably want to wheel stand everywhere. I suppose it wouldn't if he uses hard, smooth type tyres but, then it would just skate around boringly. I had a 1/5th Baja bug with the 26cc engine and yeah, that drifted ok mostly at speed with a mid to rear kind of mounting but this is much shorter wheel based and that tall engine I think will probably be pretty prone to rolling too but, it'll be a bit of a hoot either way, especially if he gets it running a lot better than here. It never even revved very well so was pointless adding nitrous, damage, probably from being too lean and consequently no lube looks like it may have already done some major damage to it. I think the nitrous attempt on a glow engine without running in and proper tuning was a very bad idea.
@@lorditsprobingtime6668Yes. Considering the cash Kev seems to have behind him, he's probably better binning that one and starting again. Once he gets this thing going, I think it's going to be either very good or very bad. I'm definitely curious to find out.
@@dazofthemoo1531 I wouldn't ever bother with one at the prices they ask but, most sensible people who've spent the money to get one will make sure they've got that pressure to the fuel tank and run it very rich and slowly start leaning it out bit by bit after several tanks full. I've seen enough running on YT to know they can really scream and do sound pretty amazing. This was not the way to do it and then shoving nitrous into it when already running lean was a very smooth brain thing to do.
I would really love to hear it running properly and in a model of some sort, it should look and sound amazing, IF he doesn't screw it up like here, what a waste!
Really cool new project Kev! I look forward to the other episodes!
Definitely do the whole thing. Highly recommended 😊❤🎉
Yes please build it. It's my favorite truck I'd love to build one after you do. Thanks Kevin
The idea is really cool, but i'd try without nitro injection, or even without the supercharger at first since that makes it harder to start. And idk if it would work well in an infraction, it would be very front heavy. Maybe put it mid mounted in a limitless so you have better weight distribution?
Nothing like spending £2k on a toy engine and blowing it up in an hour 😂
Welcome to methanol/ nos style engines or just big power race stuff, people build 80,000$ engines and burn them down on the dyno when breaking them in, before even getting to take it too the street or drop it into a car lol. Trust me, I been there unfortunately 🤦♂️🤠
@@HighSideHustler811 hahaha yeah, I get the fact that they're great little pieces of engineering, just thought they'd be more sturdy 😂
That's gunna be bad ass!!!! Can't wait to see it all together!!!
Need to see the V8 Supercharged RC truck
That mini NOS tank was made for fun in multiple ways 👍
For $2000 I would expect it to work. Make the manufacturers get you another one. Doesn't look good if it doesn't run. Would be amazing if it ran in that truck. Keep at it !!
Is the valve timing correct after the belts were removed Kevin 😊
This was my first thought when it was running like garbage. Never really sounded quite right.
Glow plugs? You mean spark plugs
you didn’t watch the whole video
The meth flow rate for stoich is higher compared to nitro “blend”. Would probably need more than vacuum feed ….Also running non oil added fuel probably quickly washed the walls and cooked a bearing 😂 but love the content!!
You're the best RUclipsr ever in the world you deserve to get described to.😊
Hey Kevin, another great vid. I love your builds and the fact that you do some of the most one and off unique projects, but sometimes it seems like you either abandon them or just don't update them anymore. I know you probably have 100000 of videos to create, but sometimes it sucks watching a really cool build and then never seeing it on the channel again.... Mp10t and the other mp10's never got more running footage :/
Disclaimer please do not inhale nitrous oxide it will make you laugh
Fun fact: automotive nitrous contains sulfer. Don't huff it.
@@uberchipmonk2568 it causes itchiness and some vomiting i call it the happy suffer ( you suffer and laugh at the same time
@@bartosbart"Now you know, and knowing is half the battle!"
I need to try that now!
It’s gone real tight ….. that’s what we all never said .
Epic builds brother .
Merry Xmas from New Zealand
🤘🏻(*ˉ︶ˉ*)🤘🏻
I would love to see this project come to life
Gotta make this come to life dude!
I love your 'American' water sounds like how Aussies would say it XD! Great video, loved the build!!
Yess!!! Please need a video on the second part!!
*DO IT KEV!!*
Yes, please do it!
Yes do it! Love the idea!
Finally someone did it
Ok no you didnt do it, you just thought about it
Yes finish the project!
I would love to see this project come alive
been binge watching your videos since Ive seen the first one this by far is my favorite one so far
Good little bash and awesome summary
Go for it man
YES IWANT TO SEE THAT!! definetely do it
Subscribed to see this project come to life
Kev, this would be an incredible project that I think everyone would love and would be very successful on that chassis and high body style
can't wait to see it in that truck :D
JONNYQ90 Said in one of his videos the supercharger rotors dont have proper clearanceing and i think thats why it would cut out and die while high reving. They will idle all day but he came to the conclusion that the supercharger is more cosmetic than actually a proper charger that makes boost. In the video while your reving the engine you can hear the rotors hitting each other. Remove supercharger then try the spray.
He loves how smart you are
Havent seen you in awhile glad you posted this to get on my fyp
V8 powered RC truck?? Yes please! After everything else you've done, i know you (likely) have the know how.
And i say this as a not-professional motor tinkerer, but maybe a gasoline conversion would make it easier to get a handle on. Just my armchair opinion. Good luck Kev!!
I’d love to have that engine! The way it is Seized!
Yesssss put it in the car
Kev, my man. You have asked a lot of dumb questions. But this one takes the cake. YES! Put it in the damn Infraction!
Isn't that the pinnacle of RC?... I mean, to have as much realism in at smaller scale that you may never experience in something full scale is my main attraction to models and RC. Just saying
I vote for a REBUILD! 💛 🦁✌
Hey Kev, by running on pure methanol you've run it without any lubrication. Model fuel has oil and methanol for this reason. I suspect you have lunched it, but I'm more than happy to tear it down and take look if you want?
It's be really cool if you could get this to work. I would recommend sending the dead engine to "I do cars" so he can give it a proper teardown on RUclips, assuming the manufacturer won't accept it as a return.
Thanks for another great video
gOOD STUFF KEV.
Absolutely YES.
Perhaps something slighty bigger.. xmax perhaps?
I've been hoping for someone to do this for months 🙏
This was a cool video
YES LETS SEE IT
Now ur doing some cool stuff foreal
Street Rod music, love it!
This is like Linus Tech Tips. Hurts me to see as a mechanical engineer and former master tech. Also your American water accent is wrong and iced tea is the best tea.
Tank wasn’t pressurized. Also supercharged with nitro on a brand new engine is crazy.
So dope you never put it in the car. Really good video man. Loved the part where you didn't do what the titled said.
He loves the stuff you buy
Would LOVE to see someone turn one of these EFI!!!