HOW TO OPERATE - A Front End Loader! HD
HTML-код
- Опубликовано: 16 авг 2017
- Like, comment, share and subscribe to my channel for more training videos .
FOLLOW ME BELOW!
/ raysvlog
/ raymond.harlall
raymondharl...
JUST GOOGLE MY NAME
www.google.ca/search?q=raymon...
Introduction to operating the Caterpillar D5 bulldozer
PART 1- FRONT END LOADER CLICK HERE --- • CATERPILLER LOADER 966...
EXCAVATORS - CLICK HERE --- • Excavators - EARTH MOV...
TRACTOR TRAILERS - CLICK HERE --- • Hook up - Tractor Trai...
MANUAL TRANSMISSIONS CLICK HERE -- • Trucker - How to Drive...
FORKLIFTS - CLICK HERE-- • UN-OFFICIAL Forklift t...
#cat
#caterpillar
#clutch
#brakes
#forward
#backwards
#neutral
#joystick
#blade
#diesle
#rpm
#operator
PART 1- FRONT END LOADER CLICK HERE --- • CATERPILLER LOADER 966...
EXCAVATORS - CLICK HERE --- • Excavators - EARTH MOV...
TRACTOR TRAILERS - CLICK HERE --- • Hook up - Tractor Trai...
MANUAL TRANSMISSIONS CLICK HERE -- • Trucker - How to Drive...
FORKLIFTS - CLICK HERE-- • UN-OFFICIAL Forklift t...
How to operate a front end loader,
caterpillar
levers - up and down or in and out
circle check,
fuel,
coolant,
engine oil,
transmission fluid,
brake and accelerator,
seat belt
bucket up and down, tilt in and out
speed,
forward and backward,
load a truck,
tractor trailer,
excavator,
construction,
safe operation,
diesel,
grease,
like a car, 
Хобби
All these people mocking him for some mistakes that have never operated any equipment especially old equipment that sticks and is really unresponsive. They would all end up threw the side of that truck if they where driving. Keep it up man no person is perfect.
I do agree with the person that said something about never enter a pile if you are not in first gear it if bad on the engine but other than that keep it up.
THANK YOU FOR YOU COMMENT MY FRIEND !
thank you for your support
and great tip!
The previous mine I worked at had a 1995 Teledyne hoe ram with terrible hydraulics that would jerk and cross-bleed. It was all I could do to not tear anything up with it, much less actually break rock!
I drive one before, not for very long, I was 17 at the time, would love to do it again
OMG !! how dirty it is !!! I worked on this in clean socks and there was a clean rug on the floor. The cabin is so wide that it allows you to immediately remove dirty shoes on the rug with a side and work in maximum comfort and cleanliness. Excellent loader. Worked on it in the conditions of the North near Vorkuta. The glass was very freezing during a snow storm. Hello to all the world’s operators from Russia!
Hello sir I'm Mohammed murshad I have experience wheel loader operator for 5 year i need a job
Lies not that much room in there for rugs n all that😆😆😆
Thanks so much. Looks very simple. Have been wanting to rent one to clear my property.
I started operating a front end loader when I was 16 working at my uncle’s concrete company business
I remember my first day in a loader. Lol
Eric Snodgrass 👌
how'd it go
I am a operator I will like to meet you in person
2 years later, I wonder if his operating skills improved? And if he learned that 1st gear gives you power and 4th gives you speed.
@@wraith0127 at least he knows faward and reverse.
Very good
Fun video. I love how quiet loaders are today. My first one had a 4-53 Detroit, once started, you throttled it to redline, like 2,500-2,800 RPM and worked all day in your open ROPS cab.
Small underground mining equipment is still like that. Open cockpit, mechanical throttle, 2300RPM and move some muck! I always bring a pair of earplugs or muffs if I'm doing more than moving the machine ten feet. I'm 24 and my hearing is already a bit jacked up from working in crusher plants, so I try to protect what I've still got.
I love this good job 👍
Engine sound very nice
Ochan #07 thank for commenting my friend be sure to follow me on Facebook
Damn that looks cool ! I want to rent one to move some snow out of my yard ! Doesn't look to complicated !
very easy! thats my second time in it!
@@raymondharlall Damn you look like you been driving it forever !
Left leaver is to tilt bucket right leaver is to raise bucket and 4th gear doesnt give more power 1st is the power
Very true on gear. 4th is more speed less torque.
Graet...thank you
Smooth as sandpaper
lol
thank you for commenting and letting me how much this video sucks
Be sure to hit SUBSCRIBE >>>>
-- Raymond Harlall
Quite useful tips
Takaidzwa Goshomi thank you for watching
Nice
At first, I thought it was a bicycle model, but after watching the video, it turned out to be true. I will definitely buy myself a bike
Is that new Country I hear on the radio? Gag! Good loader music could include classic Rock or classic Country. But nice loader. Can't hear the engine starting when you're up in the cab and it's mounted in the rear LOL.
thank you for commenting! be sure to share and subscribe! Ray
Yeah man when rocky mountain way starts playing makes my day a little better
Raymond can you make a video a front end loader loading dump truck i really want to see it
This is nice
thank you for watching, be sure to SUBSCRIBE so youtube can show my videos to other who needs to see it.
I once seen this beautiful 5 ft tall Mexican chick drive the heck out of one of these machines.
thank pretty cool! If only i was that hot i know i would have more views! lol
so good bro
All the best. Thank you for watching and subscribing. I appreciate you!
Good
How much the price
Good nice
Rana Imran 👌
thanks
Thanks a lot
Most welcome. Glad it helped. Thank you for your feedback and be sure to Subscribe 👍
that left pedal is for rim pulling bro... :)
Arn Aliangan cool
Always in first gear ⚙️ putting a load in the bucket
I heard him say " fourth gear will give you more power" 😱! The 1 gear is used to Put load in the bucket and not the fourth
I faked forklift experience over a 7minute video and they believed me. I faked Tele-handler experience and they believed me after watching a 10 minute video. Now onto dirt work with a 938 lol
haha! im guessing this is a BIG compliment to me! lol. be safe.
be sure to subscribe
@@raymondharlall yes sir, I was loader certified early last week 🙏🏻
Sorry bud but the title of the video should be “can some show me how to operate”. First off your circle check should be done before turning the key. Second always go into a pile in 1st gear or you will just chew up the transmission and third why use 2 hands for your bucket controls? They are made to be used with one hand. And finally always use 3 points of contact when getting on or off a piece of equipment.
Thank you thats 100 % great corrections to the video! Thank for your feed back Sam.
@rain Alaska ice Alaska
You check for leakes under the machine. Then you check fluids....followed by a walk around
I'm already oprerate this machine bro...not now before 15years
Thanks now I can work on a 3 million dollar project with no prior training!
Speedbird awesome. Be sure to subscribe
Cool! I'm Brazilian and I love these machines! I have good experience with heavy equipment (port area). I live in Brazil and would like to know if it is permissible for me to compete in the United States?
for sure!
Hi there. i am indian .I am also front end loader opeartor. I have 5 years +10 months experience. i have dubai and qatar licences. presently I am working in qatar and would like to know have it is front end loader opeartor job in the United states . if have , can you tell me please how can I apply.
What could be the problem?
JEZES H CHRIST!!! I HAVE TO WORK BACK SHIFT TONIGHT!!!
thank you for sharing. would be a great help if you subscribe. I appreciate your engagement
Raymond Harlall
How can i apply as operator
Where is the parking brake on this?
CAT CATERPILLAR 950 G i suppose :)
I have driven and operate with that one :)
Danijel Lukic cool
@@raymondharlall We have wheel loaders from 1970's and they are really old and bad . . . but we have CATERPILLAR 950 G and 950 F . . 950 G is from 2006 and 950 F is from 1997
This looked like a 966H. We run 972Ms, a 980G, 980Hs, a 988G and a 988H where I'm currently working.
There's drivers and screwdrivers. .. who's past u for that test stevie wonder
He's a tit!
Um the loader at my job doesn't have a steering wheel, it has a joystick but I can't find video of a CAT with a joystick
Hi! Are front-end loader and wheel loader same? I have subscribed and clicked like button!
Yes
The cylinder is correct and the seal of the cylinder is also correct.
i want EXPLAIN WRITE DOWN how to get Use
Are you able to operate this machine with az license?
You mean drivers license? As far as i know there is no license requirements to operate a loader off-road on a construction site. Just don't drive on the road. You will need proper training from an experienced, on-site operator though.
dont really need that unless you are driving on the road. you need a ticket for it most of the time. can get from union
All the best. Thank you for watching and subscribing. I appreciate you!
That’s the machine He’s driving..😆🤣
I operate my loader.
The Far left pedal is to control rim pull and
You had better check more than just fuel, transmission fluid and grease during a pre-shift inspection.
If you’re going to put out a video on how to operate a loader you should probably learn how to operate it yourself.
true
Far left pedal in the 986
And lower is a de clutch it only kicks it into neutral, and acts as a brake 988 and up is when it controls rim pull and acts as a brake
👍👍👍
The front boom cylinder is not working.
👍👍👍👍
How do u level the buxket
thank you for the great question.
1: tilt up.
2: put your bucket on the ground
3: tilt the bucket down unit you feel the front touch the ground. if front wheel uplifts up then you till too much.
hope that helps. be sure to subscribe. I appreciate your engagement
Raymond Harlall
The lower the gear the more torque not a higher gear more power. And the left pedal is a clutch brake not just a brake. Just saying
YOU ARE CORRECT. thank you for you comment. I really appreciate you. Be sure to support my channel by SUBSCRIBING :) Raymond
Give me any more help with me
Her yere gidersin bununla. Everywhere, everywhere.
I need help cat 966H
How much does a front end loader weigh
972k is 26000lbs weight i believe
Wheel loader کے training center batein joo sahe sey seekhaye
You got it my friend.
Glad it was helpful!
Watch my other videos too.
I have over 100 videos.
Please support my channel by Subscribing to my channel. Thank Ray.
Faward on the axecelerator
thank you for you comment. I really appreciate you. Be sure to support my channel by Subscribing :) Raymond
Don't ever push in anything other then 1st gear. That's how you'll be putting a new torque converter in that transmission
Tristan Horner thanks for the tip
You shouldn’t be teaching how to operate a loader, first off use a lower gear when entering a pile, second you didn’t even explain your walk around, and mostly 3 points of contact when exiting your machine you should always face your equipment and walk down it, smdh.....
People that are watching prob just want to know how to move one if they have it or how it operates because anyone certified to use one for work shouldn't be learning on youtube... lol
@@bulletclub4life I know how to run one, but only with joystick controls. Never dealt with twin-lever bucket controls before.
I push 2nd gear once it starts to feel little heavy change to first gear
Wish the camera was on his head instead of his chest, would’ve made it easier to see
next time
thank you for the suggestion
Do you need special license to operate the loader
on job site no. if drive on road yes. also if union job, they will give you license (ticket) or certification
I have a tractor trailer license what kind of license u need to drive heavy duty construction machines like backhoes and loaders and bulldozers
@@jimkontos4221 I’m pretty sure a class D. (Straight truck license will do) but Az is a big plus. What are do you live??? If in gta I got a job for you
New Jersey
Put it in first when going into a pile..
thanks
Depends on material u could get a full bucket on second gear
Press the axe sellerstor
Thank you
No truck carries 35 tons, 27 tons would be max for 80,000 gross on aluminum body and wheels dump truck. Pahleez And 4th gear gives more power?
Some of our customers run trucks over 80k gross in NM, but still nowhere near 35t of rock.
What's the price in Pakistan
to buy this machine??? like $500k usd
I want work loader operator PLZZ can u give me work I'm From India
Hi
hello. thank you for commenting,
it Would be awesome if you Subscribe to my channel :)
-- Raymond Harlall
Hi guys, all of you in comment section know your stuff. How do I get a CDL to drive a loader? Will the regular class a work?
Sumit suryavansjo
This must be a joke right. Digging in 4 gear, that will get you fired. 2 brakes. Don't put these videos up as a joke. Some dumb ass is going to get killed and it will be your fault. Left brake is a brake and trans disconnect. Right brake is just brake so if your going down a steep hill you can use brake while your in gear. Fill bucket in 1st or 2nd if loose material. Only use 4 th on road or across yard maybe. Load while going straight, never spin a tire, put bucket down at pile so you don't wear edges out fast. When you start in pile lift bucket that will transfer weight to front tires giving you more traction. I've trained 30 loader operators. Many have top jobs in gravel pits now. One of my 18 year olds just got on operating a 988 feeding a crusher with world wide company.
Gud day Boss, plz can I have a private conversation with you, I want to know more about wheeloader. I think you can help me out. I'm a incoming wheel loader operator
You should b the one making the video. Very useful information I will apply it to the next time I’m on the loader. Thanks 👍
Yeah, I honestly think that was a poor job! You didn't explain thoroughly or allow them to see you moving & picking up the load😔1 brake, 1 more like a retarder
Hii
thank you for commenting! be sure to share and subscribe! Ray
4th gear will absolutely NOT give you more power. The loader has more torque the lower the gear. This is hard to watch. Get out of the loader before you damage it
You are absolutely right cause I was shocked to hear him say that😢. I'm from Africa precisely Cameroon and my three years of experience has only been on a CAT 962H. It really cost a lot to own one in my country so such mistakes might damage the equipment 😭😫
easy
any child could drive this
4th gear ? Are you kidding me?
lol
4th gear speed I never use 4th gear only when I go into the street to move it around
I was looking for this reaction 😅when loading i only used to use 2nd gear as far as i know 4th is only for road use 🤣if you want Power put it in 1st
I'm going to drive right through the Foremans trailer if he gives me any shit
Wrong command Mr because 1st cheak all oil level fuole.. Enjen oil etc.. Then start... And working
shakeel malik you are correct
Thank you so much Mr Raymond
Mr Raymond which from country?
Who tf taught ypu how to spell my guy
Why act like this? In need of some kind of gratification? Seek help.
First check fuel def oil .check hydrolic transmission controls be sure there is no material under bucket cylinders blow out filter check great lines if yousing auto graser grease nipples that lines are broken keep pins happy it s your doll its you I AM THE LOADER ATTITUDE THEN CHECK LIGHTS WIperS report all damage number 1 take pictures blow out rads filter and engine takes about 30 min but your ass is covered
very good!
He wouldn't shovel shit from a canary!
Hi sir super love you thanks you sir be hippy Nidain Hyderabad phochmapad PETAL ODDEM MAHESH RADDYE NMASTE DIVIRN TARUK BS4 very good casllnu Good super kkk
Your loader Need, Hydrologic
front loader
thank you for you comment. I really appreciate you. Be sure to support my channel by Subscribing :) Raymond
Hello sir my name is Karandeep singh I'm wheel Loder opretor from india plese Help me job sir,
Im sorry but 1st puts more power not 4 th
M aoprtar. Sawal
Be careful with end loaders
Hello every one ..my name is tareq when iwas child i playing loader games and i love caterpillar ..now iam 28 years old my dream is have caterpillar loader but its big dream and iam very poor gay but i have hope one day i will have caterpillar loader all respect to this company reality i proud and love caterpillar company and hope have any body can make my dream fact ..iam from palestine gaza ..i love all people..🌹🙂 best regards
Really dude??. ##how to get fired on your first day being an operator!
Hard to watch;my God !!!
He lied
When are you gonna do some real work my friend anybody can play on the Loader ....💪🏾😂
I hate levers I work faster with the joystick
Wow you are not good, sorry dude the drivers want a real oprator
Travis Mckenney I know!
Me.lodaroptarhu.jobmilaga
This was not helpful at all.
Your intentions are good but your knowledge is HORRIBLE! stop talking bro.
lol. i was new on that machine!!! thank you for sharing. would be a great help if you subscribe. I appreciate your engagement
Raymond Harlall