Brilliant Thank You, no other information ive found tells me the cam pulleys are freewheeling with the nuts undone I thought they would be pegged. My cambelt was half a tooth out between the cam pulleys and the new belt wouldn't go on. Loosening the cam nuts realigned it. My mate did the last belt and it's been half a tooth out since then!! I wondered why the idle was a bit rough for the last 50,000 miles. Thanks again Brilliant.
Many Thanks for taking the time to make this video, it explains everything I need to know to replace the timing belt on my Renault Megan, one of the best videos made on replacing the timing belt. Many thanks great video.
thank you igor grate video i like home made tools as i dont have much money .dad passed away and iuse his tools .i can weld cut and bend most parts i need to fix family cars and my own .tanks again.
Can you do this job without the cam shaft locking tool? I can make one but i dont need to remove the gears nor do the waterpump so not making the tool would save me some time.
Hey Igor, Do you know, or can you measure what the thinnest diameter of the pen is? The part what snaps in the flyingwheel? 8.00 mm? I am going to make the pen of an m10 bolt. On a turning machine i will decrease the diameter partly to the thinner diameter. Thanks in advance Greetings Jeroen
Video ti je odlican al engleski katastrofa. Daj poradi malo na tom izgovoru. Da nisam vidio tablice na autu pomislio bih da si neki afrikanac. Cak i vecina rusa ima bolji izgovor.
![[EN] Watch and Work - Renault Clio II 1.6 16V](http://i.ytimg.com/vi/lN65pnRoD3w/mqdefault.jpg)
![[EN] Watch and Work - Renault Clio II 1.6 16V](/img/tr.png)
Title should be, how to disassemble a motor AND change timing belt and pump at the same time... Great video! thanx
Brilliant Thank You, no other information ive found tells me the cam pulleys are freewheeling with the nuts undone I thought they would be pegged. My cambelt was half a tooth out between the cam pulleys and the new belt wouldn't go on. Loosening the cam nuts realigned it. My mate did the last belt and it's been half a tooth out since then!! I wondered why the idle was a bit rough for the last 50,000 miles. Thanks again Brilliant.
Thanks, this is the best video in days. For tighten the camshaft pulley bolt you let the bolt (70 mm) in the inspection hole?
Yes
Usefull video until today, thank you very much ! From france
Many Thanks for taking the time to make this video, it explains everything I need to know to replace the timing belt on my Renault Megan, one of the best videos made on replacing the timing belt. Many thanks great video.
So the tensioner shouldn't be in top dead position? I locked mine in top dead position, could it be too tight?Engine runs smooth though...
If it's over tightened it will damage timing belt faster than normal
Hi, how does the water pump you installed look like? Is the mark graf good?
According to me every new part is OK because it's new it doesn't matter how manufacturer it and it's under warranty for 6 months
@@mechanicigor I used the same Graf water pump, but I closed it with an old washer, I hope the coolant does not leak
It was metal or paper gasket?
@@mechanicigor The factory washer that was on the car from the beginning and has a red color
@@rezarg5081 it's metal gasket you are safe they are good quality
thank you igor grate video i like home made tools as i dont have much money .dad passed away and iuse his tools .i can weld cut and bend most parts i need to fix family cars and my own .tanks again.
No problem glad to help and thank you for watching
Dear Igor,
What is the size of the bolt you use for blocking the flywheel?
You say "the length is 70mm"
Is it an m8 bolt?
Greetings Jeroen
Dear Jeroen that bolt is combined m10 with m8 because the hole is m8 that bolt I made from timing kit for golf mk4 for the tensioner
Thank you very much. Hvala lepo. Arsen iz Srbije.
Exellent video Sir THANKYOU!!..... Does anyone know if the valves are able to hit the pistons when a belt has slipped/snapped???
Yes they hit the pistons and usually it's big damage
Thanks for this excellent video! I used it to help with the same procedure on a 2.0i 16v petrol engine in an Espace.
If I don't have those tools for blocking the engine, how can I change the timing belt? There is another way?
You can buy tools or take the car to mechanic
Zajebista robota
Just what I needed. Thank you!
Great video - thanks! Is the procedure exactly the same for the Laguna Alize1.8 16v engine (yr 2000)?
I think yes
Very help full...
Sir where location camshaft position sensor
I think there is no camshaft sensor
Very helpfull, thank you so much, greetings from Holland.
hi. is it a 50 torx for the timing belt idler pulley? or a 55 torx?
I think it was torx 55 I'm not sure write now
Hi Igor. Thank you gor this video.
I have one question:
What's the thickness of the metal plate you use to make the camshaft bloking tool?
I think was 5mm
@@mechanicigor Thank you. Very grateful. Replacing timing belt and cooling pump in my Mégane 1.6 16v K4M today... Wish me luck... 😉
Hello, where is the horn in this car because my didn't work and I can't find it. I have the same engine and the car is from 2000 (after lifting)
It is located under the left front plastic, under the bumper.
You need to get under the car in order to replace it.
Great video I am doing head gasket on a 1.8 how do I find top dead centre.
There is plug hole for locking crankshaft check in the video
Fantastic information video. Thank you.
Thank you can you please check this video ruclips.net/video/dSB2HfG1ayE/видео.html
Can you do this job without the cam shaft locking tool? I can make one but i dont need to remove the gears nor do the waterpump so not making the tool would save me some time.
Yes you can just use marker to mark the sprockets
@@mechanicigor okay, thats what i was thinking. Thank you for replying :)
Very useful, thanks for the post.
Ile km max ten samochód może przejechać
If you are asking about timing belt 60000km it's the safety mileage for replacement
Fantastic video
hi , is this engine MPI or GDI ??
This one is mpi
@@mechanicigor
is it the one with 110hp and 145nm torque ?
I would like to make the camshaft tool my self. Do you have a drawing or dimensions so I can make the tool?
Sorry I don't have
@@mechanicigor www.meganeclub.nl/fora/index.php?topic=11489.0 i have found dimensions on google.
Position top timing belt scenic sama?
I have video of Renault scenic 1.9dci timing belt replacement
Cuál es la posición de los árbol de levas del Renault laguna 1.8 16 valvulas
Hey Igor,
Do you know, or can you measure what the thinnest diameter of the pen is?
The part what snaps in the flyingwheel? 8.00 mm?
I am going to make the pen of an m10 bolt.
On a turning machine i will decrease the diameter partly to the thinner diameter.
Thanks in advance
Greetings Jeroen
No problem glad to help
Sorry Jeroen you need 10mm of m10 so you can screw rest of the bolt needs to be 8mm and total size is 70mm
Super ti je brate engleski, za nekog ko radi mehaniku mozes slobodno u kinu da predajes...
Excellent video
Thanks!
Hello Igor,
What i previous wrote was a question.
Nice
Thanks
How cams stand
Check the video at 9:10 from there I start to explain how they should be locked
Great job thank u
Thanks igor,
You helped me a great deal!
Thanks
Great video.
Thanks 😀
Tamaj, nu ai dat tot, era motoarelor cu ardere internă a ajuns la apogeu, vor dispărea ! Atunci la ce mai folosește secretul ? Suntem ceia ce arătăm
Thanks for the useful advice, although this is a shit car to work on
Megàne 16v timing
i have that video but the video quality is bad this is the same with megane it has the same locking ponts
k4m timing 1.4 16v
I think is the same as this one
807
Help
My car will not rev will not up
Как них маскируйся, а росиянский акцент тебя выдал с потрохами.
Fuck dat
Акцент- Как серпом по яицам...
Video ti je odlican al engleski katastrofa. Daj poradi malo na tom izgovoru. Da nisam vidio tablice na autu pomislio bih da si neki afrikanac. Cak i vecina rusa ima bolji izgovor.
Borislav Djukic Fala ke probam nekogas imam tolku mnogu za kazvanje I ke gi izmesam rabotite I izgleda nejasno sepak fala
Iskreno, engleski ti je ok, sve se razumije bez ikakvih problema. Poz
Nice