As I’ve posted before I did do the SE 95 set up on my 2002 FXDL. I did add an oil cooler. The power is decent and the motor has been unbelievably reliable. I think if I was going to upgrade again that S&S 100 Sidewinder Kit looks mean and super easy. Also fairly cheap.
As many older bikers have always told me, I'm 66yrs old. The higher you go, the faster it blows. I'm plenty satisfied with 2002 deuce twin cam 88 gear drive 61,000 miles and still running strong!
We're living in a horsepower upgrade age that 20 or 30 years ago we couldn't have even dreamed of. Also, your channel focuses on the older motors and we get info here that is extremely important. Thank you.
Watching your channel has caused me to spend a little bit of money. I have 2000 Heritage Soft-tail (carbureted) which started out pretty much stock. First I upgraded the cam plate with a Screamin Eagle setup and an S&S 509 cam set. To get it to start and idle a little better I re-jetted the carb and exposed the air/fuel mixture adjustment screw and adjusted that. I was somewhat happy with the results but like most Harley riders I thought I could get more out of the old girl. I then saw this video and purchased the S&S 100 kit. I had this installed by a credible Harley mechanic, he also sent the heads off for refurbishment and some porting. He also suggested installing Twin Tec ignition module and oil cooler which I have also done as well as a better air cleaner. It wasn't loud enough so put a set of Vance and Hines 2 into 2 pipes on it. With all that I'm still not very impressed with the performance. I haven't had it dyno tested, so I can't give any specifics. It starts good but I can tell a cam with a compression release would nice. Other than buying a bigger bike I'm sure what else I can do, plus my wife would kill me. I've also considered a Mikuni carb but can't handle anymore disappointment. Any Ideas?
This guy is great. But the viewers commenting on all these videos are so valuable. So much knowledge and experience I feel like I know more about Harley’s than most Harley salesmen these days btw I went to Harley the other day and I talked to 2 kids who didn’t know know what a twin cam was 😂
You gotta be kidding me? I mean I am not shocked, but still they are selling Harleys and didn't even know what a Twin Cam was? We share a lot of information back and forth in the comments here!
I’ve been riding a used 88 I purchased four years ago. Last two years been pulling a trailer loaded with camping gear. No problems. Been to n west montana. Utah Arizona Colorado Illinois. Iowa. Wisconsin If struggled in high gear on steep climb. Just downshifted to fourth. No problems.
@@GixxerFoo I agree with you, I've been doing this for a number of years and I have less than 6 vendors that are extremely reputable in the aftermarket world. (It fits like it should and everything I need is included in the package) so I've learned I don't mind paying the couple extra bucks for quality and service. HD upgrades can be expensive and I can't tell you how many times I talk to people that have ordered stuff that didn't give you everything you need. Point being that's how some vendors can offer it at a less price. (That's been my experience) As far as I'm concerned you rank right up there with doc Harley. Thanks again for the great material you produce. I've enjoyed your channel for years now.
@@GixxerFoo S & S has a 100" Power Package Kit that in addition to the bolt in cylinders and pistons comes with TC3 oil pump, cam plate, pushrods with tubes, tappets and 585 gear drive cams for around $3,000. I'm not confident to do all of the mechanical work that requires. Would turn key labor for all this be around $1,000? Guess I need to find out from my local independant shop.
I have 02 Hertage softtail with Kerner two into one muffler! I got it at 26'000 now has 70'000 new starter and battery plugs wires all every done it it runs Great! Think am gonna go with SS 100 kit!
I enjoyed you video on the 88". I went with S&S Sidewinder 100" with screaming eagle 254E cams, at the time of the build the fly wheels were bad . They were sent out to Dark Horse crank works . They repaired them lighten& trued them .I put the 254E cams in myself .At the time of cams I had it on the Dyno, It tuned out at 79.7 hp & 80.5 ft lb of torq . It also had Fuel injectors upgraded to the 29 degree also fueling cam plate & high volume oil pump. I also put in the screaming eagle Sprocket compensator , the Harley variable pressure plate in the clutch in prep for the 100" . I don't know the what the out put is right now as I also upgraded the ECM to the thunder Max. I scared the hell out of a 117cu road glide one night would have smoked him but broke my clutch cable . I did this build on a 2006 Dyna Streetbob . my build is about a year old .
You've got that bike done right with all the parts you got supporting the build! You got a lot left in there if you want a huge power bump by swapping over to an aftermarket cam from the SE you got.
I just sent my 2002 Softail 88" cylinders and heads to Hammer Performance for a 98" bore and porting with a new carb ignition module and cometic gaskets. They do a great job and are a leader in sportster line work. Super stoked to get the parts back.
Here in central Japan I found a place that might do this (now that I am FINALLY got all the problems in my 2002 88 sorted) but its pricey. Im curious how much that's going to run you Harley Dave. It's a matter of whether the high cost here is worth it or not.
@@shizuokaBLUES I do really like Sportsters, but, man, TCs do rock! For me, though no bike is an "investment", every penny spent on maintaining, upgrading or restoring any H-D motor is worth it. Sure, they're not the best engines out there, but unmistakably they have some sort of soul, like if they were alive.
I like the Twin Cam B engines. They are pretty smooth-running; and beside a little parasitic power loss due to the counterbalancers; it can still become a reliable and powerful engine. I have a pal who has a Deuce. He had head work performed (Zippers) and cams (Zippers) and H-D's 95 cu. in. kit. A hydraulic cam tensioner was added. A SuperTrapp exhaust was installed. He and his wife have ridden the bike from Ohio to CA and it's a daily rider -- no problems whatsoever.
Those B engines are awesome, the balancer system actually worked too well and caused issues with the transmission to fall between gears. They had to give it some vibration to help complete shifts. The loss is only maybe 2 horsepower at wide open throttle with balancer.
My friend I would like to thank you, you have save me money dealing with my 2006 Road King 88 engine. I have owned four HD from 2006 RK, Electric Guilds to two Harleys Trikes 2016 and 2018. I still have my 06 Road King and of all the bikes I stated a second ago I love my 88 more then the others. I still have the 06 RK because I still LOVE the American Dream, about a month ago I traded my 2018 trike for a Honda Goldwing DCT, and my reason for the trade is because I was so tired of investment of my money into two bikes with the problem being the M8 not the 88 RK. I want to travel Long distance without the worry of a HD brake down. The RK is for small short trips around town and the GW is for long distance trips. In short and again thank you for your information that is power to customers owners of HD products, other upgrades products and last I STILL LOVE HARLEY-DAVISON MOTORCYCLES
The Gold Wings are no doubt reliable, those things run forever. The Twin Cam 88 is a very reliable motor, Harleys really aren't all that bad if you just keep with them and make sure they are gone over really well.
MAN OHHH MAN.....I absolutely LOVE the HELL OUT OF YOUR NEW MOTOR SERIES VIDEOS BRO !!!! GREAT JOB----TIHIS NEWS NEEDS TO GET OUT TO THE PUBLIC RIDERS ,,,,SOME OF US ARE GETTIN ABIT UP THERE IN AGE ...LMAO---- BUT---- WITH SOME SMARTS--A LITTLE HELP FROM COUPLE BUDDIES--FEW BEERS--AND A FEW PARTS -TOOLS-AND A BIT OF KNOW-HOW....WELL THERE YA GO---YA HAVE YOUR 100+ Horsepower -N- Torque----WE ALL KNOW THAT TORQUE IS WHAT YA FEEL TOO !!!!! It's what pulls ya !!!!! KEEP EM COMING BRO !!!!! STAY SAFE --GOD BLESS---PEACE
I have a 2003 FXD Superglide. Put the S&S 100 kit in along with Screaming Eagle heads and 50 mm carb. It has been ten years now, and the bike still rips with absolutely no problem. It is a solid combination.
Generally you would think bolting on a kit like that is going to decrease reliability. My opinion has always been just the opposite, if you keep it reasonable. Now if you put a monster cam and insane compression that's where it gets iffy.
You've got the Timken bottom end on that bike too! It's way cheaper than a new one and you have something special when you're done. Not just another new bone stock stage 1 bike like you see everywhere.
So I just did the s&s 100” sidewinder kit with 89cc super stock heads and Andrew’s tw55 cams, dynojet power commander 6 tuner with s&s 2-1 sidewinder exhaust. I’m at 7,000 feet above sea leave. I got 101 hp and 107 torque. One of the guys at work has a 2022 limited with a stock 114, I walk away form him.
All that work and only a 101 hp. Something aint right. Iv seen 98 99 hp just off a breather , exhaust and little head work, thinner head gasket and a tunner. Stock bore.
Hey Man! Thanks for the information on fuel Moto!. I just realized they are 14 mi away from my house. I have a 2005 deluxe and I'm stopping there tomorrow to have them put their 98 in big bore kit new cam plates with wood cams and do a dyno tune for me. I'm ecstatic about having a place I feel I can trust take my 88" to the next level.
Right on! That is awesome! You're very fortunate to be that close to those guys, they have a stupid amount of dyno tuning and experimentation to perfection on their kits. You're going to have one bad 88 when they get finished there!
Facts in a fast, furious format frees up fools from fruitlessly fumbling around trying to find answers on the friggin net!!! I love this... right to the point... channel!!!!
My 2002 Dyna has the 97ci kit with the 510 cams and ported heads and runs like a MoFo. I’m currently doing my 2004 softail with the 98ci kit with 510 cams and head work. I can’t wait to see the difference between the two kits. Both bikes are carb bikes.
I just bought a 98" kit from Zippers. I'm going with 9:5-1 compression and head work. I was concerned with how thin the skirts are. Will I still have good reliability going from an 88 to 98 inches? I've got a new SE cam chest and high flow oil pump, Jagg cooler, Mikuni 42 mm carb, K&N, Supertrapp 2:1, SE .510 cams and gear drive on my 01 FXDX
Have that Zipper 95 kit with the 577 cam (ThunderJet equipped S&S G carb version) on my '99 Super Glide Sport, dyno 106.1 hp and 104.0 ft-lbs with S&S slip on mufflers. I haven't had it on a dyno yet with the Vance & Hines 2 into 1 exhaust set up on it now.
I love my 88 v-twin,even running motor with great balancing and also decent power but seeing this vid makes me want to jump to the 97,I’ve got 25,000 on my Heritage Classic(03),100 year anniversary
Hey Gixxerfoo, My ride is a ‘01 RoadKing Classic. Cams, pushrods, true dual exhaust, and I believe cam chain was swapped out and if my memory was better it probably includes some other items. Liked this video quite a bit, and it will go into my library. Although age is becoming a factor.
I've got the fuel moto 98ci kit, I even went with the ported heads they offered. Everything bolted up great and the bike was running great. I just need to get a starter now and a 2 into 1 pipe to help with the power. The 6-6 cams do fall on their face after 3500 or 4000rpms. I feel like I should have went with the other cams but I'll run with these for now.
Dollar for dollar I went with Hammer Performance. 98 in. mild cam, mild porting, 9 1/2 to 1. V&H Shorties, Dyno Jet tune. HP and torque just over 100hp. 05 Softail very quick.
That's the way to do it, not a lot of people know Hammer does work on big twins. They are really known for their Sportster exploits, it's a huge savings having them bore your cylinders like that. I like that they are up front about boring to a 98 being a one time deal, a lot of places won't tell you that.
If you only want to do the big bore kit with fuel moto sending in your cylinders runs you about 700 bucks. That's them boring out your factory cylinders selling you the piston head and base gaskets and then return shipping.
That's the best way to do it honestly, Hammer Performance does that too. Hammer's thoughts are they bore your cylinder out to the max, ride it till it's wore out, and buy some new twin cam cylinders for about $280 each. It's a huge savings over the kits just boring your factory cylinders.
2001 FLHTCUI, I went with the Dave Mackie 95" with DM590 cam, 20° JM domed piston's, Heads and Cylinders done by DM, 51mm ThunderMax EFI, V&H 2n1 chrome pro pipe... I wanted to jump the HP and TQ but still maintain reliability for touring, I am 64 yo not looking to enter the Senior National Bagger Championships lol I am at about 105HP and 104TQ.. still get great fuel mileage unless I twist to go...
Thinking about getting the S&S power pack kit for my 88. I got the bike looking the way I want and have the Bassani RR3 with the Arlen Ness monster sucker already. Hoping for good results. Not positive but I believe the 100 inch sidewinder comes with the power pack
I have the sidewinder 100 inch jugs and pistons. Also running ported super stock heads 10.5.1 cpr and 575 lift cam set and i just got 125 hp at the tire and 115 lbft . This is a 05 fatboy i built and boy it runs
The FuelMoto kits are really nice, they cost more but you get everything you need in one place. Boring cylinders with the right parts works very well too!
Im glad for this video. Im going to be having the 100 s&s kit installed and my local shop explained the difference much as you did. The bigger cc seems to pay on dyno. Im running a stock 88 now and will let you know how it changes. The 60ish hp it has now is pretty slow and disappointing. I did pipes and power commander then finally cams and its still needs more to be up to speed bike only 5 years newer.
The increase in bore is going to pay dividends in torque! A good cam with a compression bump is going to give you a serious horsepower boost! Best part is all that is a lot less expensive than a new bike you have something special when you're done.
i like big inch, BUT, i want tall gearing, for maximum range. i love using big motors, running lazily, giving crazy range. so far my best was a 58mpg chopper, set up for touring, 6 gallon tanks. i want to see 65-70mpg. someday. so light weight bike, with suspension, but big motor, tall gears, and ride, i was once a 40k mile a year rider.
Awesome content man. I have a ‘06 Dyna Lowrider with 88 TC engine. I’ve done full pipes, aftermarket air cleaner, and custom tune (Powervision Dynojet). With winter coming and having 36k miles on it, I’m gonna pull the cam cover off and see what’s going on in there. I’m leaning towards a 509 cam mid-low end cam since this is my “bitch around town bike.”
I am Low Rider guy myself, l love those bikes. You've got a good setup going on your bike. The front tensioner is easy to see but the back is a real pain. It's a good thing you're looking in on it with 36k.
I was looking to do this with my 99 RK but there was no support for the MM fuel injection and I didn't really want to take out a system that was still functioning very well to retune it with a carb. Sold that bike and got a 2014 FLHTP and did the normal Stage 1 upgrades and am very happy with it.
@@GixxerFoo Power Vision thru Fuel Moto. Did intake, new head pipe and used mufflers I already had. I had the urge to do cams but after this upgrade bike runs great and has all the power I need.
It's hard to beat FuelMoto, l ordered my dad's Power Vision through them for his Vrod. They have been great to work with, l love how they already put one of their in house developed maps on there.
There are several deals available doing the big bore kit, as of June 2022, that seem appealing. I have done the S&S 509G upgrade and am now considering whether to go with new cylinder heads or doing the bore. 97" is under $1,000 and 100" is just wee bit over that. My bike is a 2003 FLHTCI with 26,000 miles on it. I am willing to put another couple of thousand dollars into it just to increase reliability for a cross country trip. It has plenty of power and torque, for an old guy! I can do all of my own work. What do you think, new cylinder heads or the big bore kit?
What changes would need to be made on a carbureted model being upgraded? Additionally, what oil cooling system do you recommend and can you do an explanation on the install? Love the vids bro!
Thank you! Each manufacturer will recommend a starting point for carb settings. Definently a jet kit and going richer, they are gonna need some fuel for sure. Harley oil coolers are really good, Jagg would be my choice in an aftermarket cooler. Jagg has coolers with thermostats and fans, those are really awesome setups.
Thank you so much for your videos im only a year into owning Harleys an love it. I have an stock like new 03 flht with 1600miles except for a full Reinheart exhaust that im looking to hope up and do away with the cam chain tensioner. Taking notes everytime i watch your videos
1600 miles on an 03? The cam chain tensioner system is really the only draw back on the 88. Once you get a hydraulic in there you're golden. I appreciate you're support on the channel!
@@shizuokaBLUES As for the stator, no problem. As for the overheating, it is an issue if the bike is driven in a traffic jam, but anyway, an air cooled motor likes continuous riding, so overheating is not even a concern if air flow is constant.
Omar Salgado well my stator melted this summer because of the insane heat and humidity (and exactly as you said -being caught in a traffic jam). But it was 18 years old and this is central Japan 🥵 so what do I expect eh? I’ve never had an oil cooled engine before because my bikes have always been Yamahas or Suzuki’s built for these brutal summers. Live and learn. Thanks for your comment. As for bike as a non-investment I agree. My investments and savings are there to pay for things like this and that’s part of the joy of life if you are blessed enough to afford it. But I will say that ....selling a made-in-Shizuoka Yamaha SR400 (single /40 year old design) for an older dyna with built-in issues WAS one of the stupider things I’ve ever done. I’ve gone from loving riding in the mountains to quietly dreading it. Will it break down YET AGAIN? Will it cost me another 1K or another 2K? What’s next -the starter? The main bearing ? The transmission bearing ? I’ve realized that riding an older Harley is a hobby and should be your second or third bike. The first one or two being Japanese or newer harleys (and you have a serious garage and tools) So I half agree with you and half can’t quite see due to the mistake I’ve made of listening to Harley fans Who won’t objectively look at their bikes (out of loyalty and ego) and only encourage others to be more like them. But live and learn and be grateful for even having a beautiful old motorcycle , a luxury in and of itself. This I Know Happy riding and cheers 🍻
@@shizuokaBLUES Such a sad thing, really. I think you bought a seriously trashed bike. I say this because I own two H-Ds, one since very brand new 2007 Sportster and a used 2005 Softail, which both have needed maintenance, one from abuse and the other from being stored almost seven years, but not tragic failures. Indeed, I can state that the abused one, the Sportster, has stood all the beating like a champ. I remember one day that I rode it for 14 continuous hours and it never hesitated. Indeed, the stator broke years later due to maintenance negligence. That's why I say you bought a very abused bike in the interior. But overall, if proper maintenance is done in time and form, the bikes are bulletproof, and though I own a couple, I'm not that of a fan, because I like other brands, including the Japanese sport bikes. I have to tell you that any bike will have its issues if abused and not maintained, including the Japanese ones, which I've seen broken down on the road. Greetings.
Yup; that’s way I’m go’n - 🤠✊👍🏻👌 hd has the 4”cyls with steel liners that fit in the case spigots - they are for the 96 so you will have to hunt for pistons 4” stoke and rings for steel liners .
I was looking at the "S&S 100/110" POWER PACKAGE FOR 1999-2017 HARLEY-DAVIDSON BIG TWINS" for my 88". It has everything I think I need. Upgraded oil pump, cam plate, and I really like the gear cams over chain. What do you think of this upgrade?
That's an awesome package, the gear drive system is very dependent on the shaft run out being in spec, .003 or less 😬. The gear drives are awesome and worry free, expensive upfront though.
@@GixxerFoo I would be hesitant going with gear drive cams on the twin cam 88 without upgrading to a new welded crankshaft or having the factory crankshaft trued and welded, I hear that even if the runout is within .003 that it may not stay there. I think I would feel uneasy about them on a stock crankshaft.
If the run out is within spec when it's installed l really haven't heard of many failures unless the run out just became atrocious. But by that time you've got some really serious issues.
😆😂👍 that's awesome! I still watch a lot of videos myself too, I like to compare opinions and see what others are doing as well too. Some I agree with and others I wanna know the who, what, when, why and how.
Really Enjoy the details you have in this video. Will you be making any more video on the Hammer Performance Products such as the 1275 kits with 560 or 570 cams.
I'd stay with the 95"... I like to leave room for improvement and rebuildability. Longevity is also a concern. Cost is another. At some point a S&S crate motor is better.
Thank you very much! I really appreciate the support! We've had a major ice storm here in Oklahoma and I wasn't able to get another video this week. We'll be back next Friday for sure, but I a am hoping to get power back and get 2 videos for next week.
I'm thankful for you and your channel. I've owned a couple HD, s. Cut my teeth on the iron head, then I had a 93 Fatboy, EVO, s are fabulous little engines. I recently purchased a 06 Flhpi. Your channel has taught me about the TC and the options I have to choose from. Thanks brother
@@GixxerFoo yeah that's one reason I was thinking about a Zipper kit on my 2017 with the 107ci , give me your honest opinion on what route you would go with the 107, I would appreciate it 💯👍🏼
I'm not really familiar with the Zippers Kit for the M8, but l would go with a bolt on 124 and a nice torque cam on the 107. The 4 valve head really opens a world of possibilities on those.
No problem, just watch the power numbers and the price. Especially with aftermarket kits, the right combination can really make some power even if it's smaller displacement.
Nice info, Thanks. Question: I just bought a 2003 FXST Carbed w/ hooker headers, want more power so what about this plan. I'm thinking of the S & S 100 ci kit, S & S super E carb, 585 cams ? and entire cam chest upgrade, head work also. Do you feel this a viable plan or am i missing something. I want power but still have a daily cruiser without having to wrench on it constantly. Thanks for your help in advance and Take Care Brother..
I have a Early production 04 Road King custom converted to a stripped Classic. Carb motor CV 44 woods needle. SE manifold. S&S air cleaner back plate kit. 203 cams with Upgraded cam tensioner and cam plate & pump & bearings. I wanted to do heads however all the heads had too much running compression. SE ignition for cams and big bore kit. Now Harley has Factory ported heads that keep compression stock as 203 cams need to stay under 9.5 static . I feel this is a good upgrade for 88 or 95 milled motors. I really comes on around 60 mph. However t don't do much hyw driving. I don't want to have to upgrade my starter as it is sensitive to hot starts sometimes. I'm running a oil filter billet cooler which looks cool lol. Any thoughts 💬💭
Yes that would be correct , but, on my 88 I’ve found that the kits only offer the basic kit, and, I’m kind of lost as to what I need to actually buy, and, I don’t want to order parts I don’t need. I honestly think I could manage the install, but, my mechanic ability Belgians to fail the order forms like; do I need a install kit, do I need new bearing , can I use my stock cam plate and oil pump, if I buy the 100 sidewinder do I need new valve springs, should I by new heads or send them out to be reworked, which parts should be installed first. I think a video explaining this on a 96 or a 88 would be a very informative video.
You can still use your stock heads with the 100 inch kit, even the stock cam if you wanted to. It just wouldn't take full advantage of the added displacement. Valve springs are really dependent on the cam you use, cam manufacturers will specify if you can run stock springs or if you need to upgrade. Just depends how aggressive the cam is, now replacing bearings is all a good idea with a build. The stock cam plates are fine, but a billet cam plate adds more support but isn't really necessary unless you really ride hard.
Question...I have a 06 wide glide 88 efi. about 18k miles on it. I bought it used and don't know if it has work done other than what I can see. The shop that did the work has long closed and I cant seem to get any records. Screaming eagle pipes staggered and screaming eagle intake on it. I assume it must have gotten a tune. I would like to put on the SS 100 sidewinder kit that comes with cams for high torque. I really like the idea of 100 hp and 100 plus torque. I'm not a racer by any stretch just a cruiser but I'm kind of over my friends pulling away from me with their Road kings, Street glides and Road glides. I mean I am 100 pounds lighter right? So I also like the sound of the screaming eagle pipes on it (amazing sound) and don't really want to spend extra money on 2 into 1 exhaust if I can help it. How much torque would I be giving up to keep the exhaust? Is that ok or do I really need to change them? Also do I need new cam tensioners and an oil cooler for this upgrade? What would you do to kick it up to this decade without breaking the bank and also keep the reliability? Also do I need to also get the frame brace or replace the engine mounts if I add torque- or can the old frame handle it? And how much about would I have to pay in to get all this work done?
You wouldn't really give up much if anything with the SE exhaust of that era, with the factory header it's really the best of both worlds. You get the sound of a 2 into 2 with the power of a 2 into 1. 2006 Dyna already has the hydraulic tensioners, they only did that on the Dyna that year. The cases are basically 96 cases with a bore for 88 cylinders and the heads are what basically later became the heads of the 96. Great year for the dyna! The 100 kit will drop and you'll want a good cam too, S&S 585 is a good Dyna cam or a Wood TW-555 is a killer Dyna cam. Hard to say what it would cost but the 100 kit about 1200, figure about 3 to 400 for a cam. Labor l am ball parking 2,000. Gaskets, oil etc, 300, and a dyno tune about 3 to 400. Total ball park guess l would say ridiculously high 4500. But indy shop with a can tune maybe around 3500.
@@GixxerFoo Sorry for my ignorance but what is "indy shop with a can tune?" Also my bike got the heavy-duty fork springs and new Ledged shocks in the rear. It has not ever wobbled -had it up to 85 few times. In your opinion will the extra torque flex this Dyna frame and create a wobble?- I read stories about that possible wobble- I have no problem-but I do not want to create a problem either.
At 100 horse you're good with the stock injectors, once you start pushing the motor up over 110 that's when it's going to be time to start looking at a bit larger injector. Too big of an injector can do more harm than good, here's a video about injector sizing that explains more ruclips.net/video/PaiSNfnLfsc/видео.html
Can you give me a list of all the parts. Complete exhaust system , One hundred hot ride kit, Tuner.. What cams were put in the bike? Iam seaching for chop. Have 2010 ultra bone stock. Live in Darien WI so close for service. Looking for the exact same setup as this gentleman Ben. Please reply. Thanks Mark
Question about Big Bore Kits and a stock clutch. I have a 2002 Softail Fatboy I want to put either a Fuel Moto 98" or the S & S 100" Power Package on and I will also replace my heads. By increasing hp and torque I should probably upgrade my clutch. Fuel Moto has a variable pressure clutch that supports 130Hp/130Tq with OEM spring. Should I try it with my original clutch first or just go ahead and do something with the clutch when I do the big bore kit and heads? What clutch upgrades should I do? I don't know much about what all is involved and will ask the mechanic that installs the other upgrades I mentioned his advice. I value your opinions and advice a great deal. Thanks!
You can get there with a bolt on 95 and using a Wood Cam. Depends on your year and if you're carb or fuel injection. Bump the compression to 10:1 with some mild head porting and it will bang out 100. 100 horse is a great number for Twin Cam, plenty of power and reliable.
I already encountered my first issue n the break in...may have a lil too much torque id like to believe...but honestly idk what happened..my pulley broke..all 5 screws..so ima drill n tap or "ez out" ....this thing is a monster...i ran down a stock m8 114 breakout ..i need a tune now. My ecm is locked with tts master pro...what can i donto start fresh get a new ecm..btw im the guy with the screaming eagle 103 with mild worked heads 543 reaper cams domed pistons fueling oil pump amd camplate...im unsure what to do next. I may be thinking too small...why not 124 if im have to crack the cases anyway..
Good day Great Channel 👍 I am planning to get a play bike after 10 years out of the saddle my age is 65 My rides will be under 100 to 150 km. I am mechanical inclined and built many metric sport bikes Looking at my old favorite shovelhead or a newer Evo bike around 2005 What is you recommendation Thanks in advance
The case bore is smaller on the 88 so the drop on jugs won't fit the 88. You'd need to go with 95 inch cylinders and then a stroker crank. The 100 inch drop on kit the biggest one out there for the 88 with the stock crank.
Question. I thought I heard you say the Fuel Moto cylinders had more cooling surface/fins early in your video, and then at the end you said S&S. So did you misspeak? Do they both have that feature? Am I a poor listener? Lol Thanks for the breakdown and information!
Yeah they will bolt up and they actually flow a lot better, even the stock 103 heads would be a big improvement. The 100" kit is made to work with the stock 88 heads so the 103 heads will bolt right on, you'll just have to use late model flanges on the intake. You can plug the ACR's or wire them to the starter solenoid, maybe put some manual ACR's in there if you want.
It's never a bad idea to upgrade to heavier spring or centrifugal spring assist. A stock clutch with some miles on it may actually slip, especially depending how you ride. If you got the cash get a good clutch basket and go all out!
would you have any suggestions on a higher lift cams for a "06 FLHXI with the Harley 95" big bore kit installed, I run the Bassani true dual power curve exhaust with 4" Road Shark mufflers.
Thank you for a very valuable information 👍👍 Would it be possible to make a video about big bore kits for the 88” that DO require case machining and crankshaft work ? Or , maybe even kits that offer new crankshaft, if there are any 🤔 ?! How expensive would it get ? Do you have to find a shop to do your machining locally or can you send your cases or even complete engine to those who offer the kits for a complete big bore overhaul? Thanks 👌👍✌️
Not a bad idea, S&S and Zippers make serious kits with stroker cranks that you get to do a full case machining with. I believe with S&S they have a program where you can send your cases in, l know they do that with your heads.
Would you stay with a 95 inch kit or go with the 97, 98 or even the 100 inch Sidewinder bolt on?
As I’ve posted before I did do the SE 95 set up on my 2002 FXDL. I did add an oil cooler. The power is decent and the motor has been unbelievably reliable. I think if I was going to upgrade again that S&S 100 Sidewinder Kit looks mean and super easy. Also fairly cheap.
96" Twin Cam plus Sidewinder kit equals 110"?
The price of the S&S isn't too bad, it's not as good of a deal as the SE kit but it makes some serious power.
You are correct, they make one for the 96 and you can bolt on 110 inches.
I'll run my 88" against any displacement Harley heads/jugs
As many older bikers have always told me, I'm 66yrs old. The higher you go, the faster it blows. I'm plenty satisfied with 2002 deuce twin cam 88 gear drive 61,000 miles and still running strong!
Have you had to replace cam tensioner?
Everyone’s done that by 60k no doubt
Actually by 30 if your being safe
@@Anonymouso283it’s gear drive…. He said GEAR drive….
Excellent comment!👍
We're living in a horsepower upgrade age that 20 or 30 years ago we couldn't have even dreamed of.
Also, your channel focuses on the older motors and we get info here that is extremely important.
Thank you.
Right on! We're seeing horsepower numbers out of this 45 degree design we never thought possible now, well reliably anyway lol.
Enjoy this video. Glad to see that us 88ci people weren’t forgotten about.
Thank you, the 88 is the last of later design engines that you can still get a carburetor on.
Watching your channel has caused me to spend a little bit of money. I have 2000 Heritage Soft-tail (carbureted) which started out pretty much stock. First I upgraded the cam plate with a Screamin Eagle setup and an S&S 509 cam set. To get it to start and idle a little better I re-jetted the carb and exposed the air/fuel mixture adjustment screw and adjusted that. I was somewhat happy with the results but like most Harley riders I thought I could get more out of the old girl. I then saw this video and purchased the S&S 100 kit. I had this installed by a credible Harley mechanic, he also sent the heads off for refurbishment and some porting. He also suggested installing Twin Tec ignition module and oil cooler which I have also done as well as a better air cleaner. It wasn't loud enough so put a set of Vance and Hines 2 into 2 pipes on it. With all that I'm still not very impressed with the performance. I haven't had it dyno tested, so I can't give any specifics. It starts good but I can tell a cam with a compression release would nice. Other than buying a bigger bike I'm sure what else I can do, plus my wife would kill me. I've also considered a Mikuni carb but can't handle anymore disappointment. Any Ideas?
That bike well tuned should be around 100 horsepower and torque, you might go with a little more cam if you're wanting more out of it.
This guy is great. But the viewers commenting on all these videos are so valuable. So much knowledge and experience I feel like I know more about Harley’s than most Harley salesmen these days btw I went to Harley the other day and I talked to 2 kids who didn’t know know what a twin cam was 😂
You gotta be kidding me? I mean I am not shocked, but still they are selling Harleys and didn't even know what a Twin Cam was? We share a lot of information back and forth in the comments here!
I’ve been riding a used 88 I purchased four years ago. Last two years been pulling a trailer loaded with camping gear. No problems. Been to n west montana. Utah Arizona Colorado Illinois. Iowa. Wisconsin If struggled in high gear on steep climb. Just downshifted to fourth. No problems.
I like the fact that you put the pricing in with these upgrades. Thanks again for another great video.
Thank you! The prices vary quite a bit depending on where you decide to buy it from though too.
@@GixxerFoo I agree with you, I've been doing this for a number of years and I have less than 6 vendors that are extremely reputable in the aftermarket world.
(It fits like it should and everything I need is included in the package) so I've learned I don't mind paying the couple extra bucks for quality and service. HD upgrades can be expensive and I can't tell you how many times I talk to people that have ordered stuff that didn't give you everything you need. Point being that's how some vendors can offer it at a less price.
(That's been my experience)
As far as I'm concerned you rank right up there with doc Harley.
Thanks again for the great material you produce. I've enjoyed your channel for years now.
@@GixxerFoo S & S has a 100" Power Package Kit that in addition to the bolt in cylinders and pistons comes with TC3 oil pump, cam plate, pushrods with tubes, tappets and 585 gear drive cams for around $3,000. I'm not confident to do all of the mechanical work that requires. Would turn key labor for all this be around $1,000? Guess I need to find out from my local independant shop.
I have 02 Hertage softtail with Kerner two into one muffler! I got it at 26'000 now has 70'000 new starter and battery plugs wires all every done it it runs Great! Think am gonna go with SS 100 kit!
I enjoyed you video on the 88".
I went with S&S Sidewinder 100" with screaming eagle 254E cams, at the time of the build the fly wheels were bad . They were sent out to Dark Horse crank works . They repaired them lighten& trued them .I put the 254E cams in myself .At the time of cams I had it on the Dyno, It tuned out at 79.7 hp & 80.5 ft lb of torq . It also had Fuel injectors upgraded to the 29 degree also fueling cam plate & high volume oil pump. I also put in the screaming eagle Sprocket compensator , the Harley variable pressure plate in the clutch in prep for the 100" . I don't know the what the out put is right now as I also upgraded the ECM to the thunder Max. I scared the hell out of a 117cu road glide one night would have smoked him but broke my clutch cable . I did this build on a 2006 Dyna Streetbob . my build is about a year old .
You've got that bike done right with all the parts you got supporting the build! You got a lot left in there if you want a huge power bump by swapping over to an aftermarket cam from the SE you got.
I just sent my 2002 Softail 88" cylinders and heads to Hammer Performance for a 98" bore and porting with a new carb ignition module and cometic gaskets. They do a great job and are a leader in sportster line work. Super stoked to get the parts back.
Hammer does a great job on big twins too, a lot of people don't even realize they do work on big twins. They are reasonable to compared to these kits.
Here in central Japan I found a place that might do this (now that I am FINALLY got all the problems in my 2002 88 sorted) but its pricey. Im curious how much that's going to run you Harley Dave. It's a matter of whether the high cost here is worth it or not.
You'll notice a huge difference, it will be like a new bike.
@@shizuokaBLUES I do really like Sportsters, but, man, TCs do rock! For me, though no bike is an "investment", every penny spent on maintaining, upgrading or restoring any H-D motor is worth it. Sure, they're not the best engines out there, but unmistakably they have some sort of soul, like if they were alive.
👍 that's exactly what is so much fun about working on and riding Harleys.
I like the Twin Cam B engines. They are pretty smooth-running; and beside a little parasitic power loss due to the counterbalancers; it can still become a reliable and powerful engine. I have a pal who has a Deuce. He had head work performed (Zippers) and cams (Zippers) and H-D's 95 cu. in. kit. A hydraulic cam tensioner was added. A SuperTrapp exhaust was installed. He and his wife have ridden the bike from Ohio to CA and it's a daily rider -- no problems whatsoever.
Those B engines are awesome, the balancer system actually worked too well and caused issues with the transmission to fall between gears. They had to give it some vibration to help complete shifts. The loss is only maybe 2 horsepower at wide open throttle with balancer.
This is a great channel, and your delivery is almost like listening to a good podcast. Rare. Subscribed.
Welcome aboard! I just try to get the information out there all in one place!
Yep I put Gixxer on at work ! I've listened threw his vids a few times over now . Always excited for new content
Hmmm
I have stock jugs with a 95" bore, ported heads, Andrew's midrange cams and a MasterTune pro tune and I'm pushing 100HP and 110 ft lbs...
My friend I would like to thank you, you have save me money dealing with my 2006 Road King 88 engine. I have owned four HD from 2006 RK, Electric Guilds to two Harleys Trikes 2016 and 2018. I still have my 06 Road King and of all the bikes I stated a second ago I love my 88 more then the others. I still have the 06 RK because I still LOVE the American Dream, about a month ago I traded my 2018 trike for a Honda Goldwing DCT, and my reason for the trade is because I was so tired of investment of my money into two bikes with the problem being the M8 not the 88 RK. I want to travel Long distance without the worry of a HD brake down. The RK is for small short trips around town and the GW is for long distance trips. In short and again thank you for your information that is power to customers owners of HD products, other upgrades products and last I STILL LOVE HARLEY-DAVISON MOTORCYCLES
The Gold Wings are no doubt reliable, those things run forever. The Twin Cam 88 is a very reliable motor, Harleys really aren't all that bad if you just keep with them and make sure they are gone over really well.
@@GixxerFoo Thank you, may God alway keep you and your family safe and God Blessing ALWAYS 🙂
You definitely break these options down better than any other channel I've watched
MAN OHHH MAN.....I absolutely LOVE the HELL OUT OF YOUR NEW MOTOR SERIES VIDEOS BRO !!!! GREAT JOB----TIHIS NEWS NEEDS TO GET OUT TO THE PUBLIC RIDERS ,,,,SOME OF US ARE GETTIN ABIT UP THERE IN AGE ...LMAO---- BUT---- WITH SOME SMARTS--A LITTLE HELP FROM COUPLE BUDDIES--FEW BEERS--AND A FEW PARTS -TOOLS-AND A BIT OF KNOW-HOW....WELL THERE YA GO---YA HAVE YOUR 100+ Horsepower -N- Torque----WE ALL KNOW THAT TORQUE IS WHAT YA FEEL TOO !!!!! It's what pulls ya !!!!! KEEP EM COMING BRO !!!!! STAY SAFE --GOD BLESS---PEACE
I have a 2003 FXD Superglide. Put the S&S 100 kit in along with Screaming Eagle heads and 50 mm carb. It has been ten years now, and the bike still rips with absolutely no problem. It is a solid combination.
Generally you would think bolting on a kit like that is going to decrease reliability. My opinion has always been just the opposite, if you keep it reasonable. Now if you put a monster cam and insane compression that's where it gets iffy.
@@GixxerFoo it has a 625 cam kit, and Darkhorse flywheels. Lots of work. I don’t go crazy with it, but enjoy the power.
Whew... damn. It's definently got some work, more than enough to get in trouble!
Anything screaming eagle is the great value version of Harley Davidson parts
Had Kevin Baxter build my 88 to a 117 on my trike conversion. It runs great down the interstate at 70 & 75.
Kevin Baxter builds a damn good motor, I would trust that guy all day every day. I bet that trike flys now!
Only if you would enjoy it but you would do a killer podcast imo. I drive a semi and would enjoy listening for sure. Keep up the good work !
Thank you, l appreciate that. I'll have to look into doing a podcast, l really hadn't thought about that before 🤔.
I have an 02 Fatboy. And this has really opened my eyes And probably my pocket book to the idea of more horsepower. Seems like a good idea for me.
You've got the Timken bottom end on that bike too! It's way cheaper than a new one and you have something special when you're done. Not just another new bone stock stage 1 bike like you see everywhere.
@@GixxerFoo you're getting me excited about this bike again
So I just did the s&s 100” sidewinder kit with 89cc super stock heads and Andrew’s tw55 cams, dynojet power commander 6 tuner with s&s 2-1 sidewinder exhaust. I’m at 7,000 feet above sea leave. I got 101 hp and 107 torque. One of the guys at work has a 2022 limited with a stock 114, I walk away form him.
What was the total cost on doing all that
All that work and only a 101 hp. Something aint right. Iv seen 98 99 hp just off a breather , exhaust and little head work, thinner head gasket and a tunner. Stock bore.
Hey Man! Thanks for the information on fuel Moto!. I just realized they are 14 mi away from my house. I have a 2005 deluxe and I'm stopping there tomorrow to have them put their 98 in big bore kit new cam plates with wood cams and do a dyno tune for me. I'm ecstatic about having a place I feel I can trust take my 88" to the next level.
Right on! That is awesome! You're very fortunate to be that close to those guys, they have a stupid amount of dyno tuning and experimentation to perfection on their kits. You're going to have one bad 88 when they get finished there!
Facts in a fast, furious format frees up fools from fruitlessly fumbling around trying to find answers on the friggin net!!! I love this... right to the point... channel!!!!
My 2002 Dyna has the 97ci kit with the 510 cams and ported heads and runs like a MoFo. I’m currently doing my 2004 softail with the 98ci kit with 510 cams and head work. I can’t wait to see the difference between the two kits. Both bikes are carb bikes.
You throw some head work in there like you've done and they will easily break 100hp. That's better than the average on any of the 103's out there.
I just bought a 98" kit from Zippers. I'm going with 9:5-1 compression and head work. I was concerned with how thin the skirts are. Will I still have good reliability going from an 88 to 98 inches? I've got a new SE cam chest and high flow oil pump, Jagg cooler, Mikuni 42 mm carb, K&N, Supertrapp 2:1, SE .510 cams and gear drive on my 01 FXDX
@@paulfiore7083 I think you’ll love it
I'll keep my zippers 95c.i kit. 577 cams, S&S pushrods, lifters and gear drive cams. Larger intake & injectors and a Thundermax tuner. Definitely tire shreader😎
Dang that's a hell of a setup right there, that's gotta be a handful if you get out of shape.
Have that Zipper 95 kit with the 577 cam (ThunderJet equipped S&S G carb version) on my '99 Super Glide Sport, dyno 106.1 hp and 104.0 ft-lbs with S&S slip on mufflers. I haven't had it on a dyno yet with the Vance & Hines 2 into 1 exhaust set up on it now.
I love my 88 v-twin,even running motor with great balancing and also decent power but seeing this vid makes me want to jump to the 97,I’ve got 25,000 on my Heritage Classic(03),100 year anniversary
It’s like your reading my mind... I’ve been meaning to ask you this exact question...thanks for the info...I’ll keep you posted on my build
That's awesome! Please do, keep me updated on your progress.
Hey Gixxerfoo, My ride is a ‘01 RoadKing Classic. Cams, pushrods, true dual exhaust, and I believe cam chain was swapped out and if my memory was better it probably includes some other items. Liked this video quite a bit, and it will go into my library. Although age is becoming a factor.
I've got the fuel moto 98ci kit, I even went with the ported heads they offered. Everything bolted up great and the bike was running great. I just need to get a starter now and a 2 into 1 pipe to help with the power. The 6-6 cams do fall on their face after 3500 or 4000rpms. I feel like I should have went with the other cams but I'll run with these for now.
FuelMoto has some mean kits, that 98 kit runs very strong!
How much did everything cost?
T w 6 Bob wood cams night Prowler
Dollar for dollar I went with Hammer Performance. 98 in. mild cam, mild porting, 9 1/2 to 1. V&H Shorties, Dyno Jet tune. HP and torque just over 100hp. 05 Softail very quick.
That's the way to do it, not a lot of people know Hammer does work on big twins. They are really known for their Sportster exploits, it's a huge savings having them bore your cylinders like that. I like that they are up front about boring to a 98 being a one time deal, a lot of places won't tell you that.
@@GixxerFoo Why not just bore to a 96", leaving headroom for the next rebuild? 'Course, I'm financially strapped and ride a LOT.
That's actually very cost effective and Hammer Performance has a really good deal on bore jobs for Twin Cams.
What cam did you end up using?
If you only want to do the big bore kit with fuel moto sending in your cylinders runs you about 700 bucks. That's them boring out your factory cylinders selling you the piston head and base gaskets and then return shipping.
That's the best way to do it honestly, Hammer Performance does that too. Hammer's thoughts are they bore your cylinder out to the max, ride it till it's wore out, and buy some new twin cam cylinders for about $280 each. It's a huge savings over the kits just boring your factory cylinders.
I went with the S&S 100” kit with S&S heads…..super G carb and the V&H big radius exhaust……had to upgrade my clutch as well along with the ignition.
2001 FLHTCUI, I went with the Dave Mackie 95" with DM590 cam, 20° JM domed piston's, Heads and Cylinders done by DM, 51mm ThunderMax EFI, V&H 2n1 chrome pro pipe... I wanted to jump the HP and TQ but still maintain reliability for touring, I am 64 yo not looking to enter the Senior National Bagger Championships lol I am at about 105HP and 104TQ.. still get great fuel mileage unless I twist to go...
That's the best way to go about it right there, good solid power and still reliable.
I have a 2004 softail springer with an 88 TC. I'd love to put one of these aftermarket kits on there. Thanks for al the information, brother
Glad to help!
Ive got a 106 stroker in my dedicated drag dyna. Running in the 10s 1/4 mile. On my second season running it. Only changed rings.
Gixxerfoo you have a great channel with the best information available 💪🐐👍🔥 Thank you for sharing your knowledge bro
Thank you! We greatly appreciate you taking the time to watch!! I love to put it out there and be honest and straight forward about it!
Thanks I just started investigating these kit s&s all the way
S&S is very high quality and they make the power, pricey. But there is is a good reason for it.
Thinking about getting the S&S power pack kit for my 88. I got the bike looking the way I want and have the Bassani RR3 with the Arlen Ness monster sucker already. Hoping for good results. Not positive but I believe the 100 inch sidewinder comes with the power pack
That kit will transform your 88, the short stroke of the 88 makes for one hell of a motor once you get them worked over!
@@GixxerFoo what’s a better cam for my 88? The 509 or 510?
This is the exact video I was looking for. Thank you!
Glad it was helpful! I hope you found the information you were after!
I have the sidewinder 100 inch jugs and pistons. Also running ported super stock heads 10.5.1 cpr and 575 lift cam set and i just got 125 hp at the tire and 115 lbft . This is a 05 fatboy i built and boy it runs
Making them M8 guys that spent the big bucks mad!!
I did a S&S106 stroker on mine n 55 throtle body . N she made 95 hp 110 torque to back wheel
You should really investigate the Fuel Moto kit. Everything you need to do it right. I’m torn between boring my cylinders vs buying cylinders
The FuelMoto kits are really nice, they cost more but you get everything you need in one place. Boring cylinders with the right parts works very well too!
Im glad for this video.
Im going to be having the 100 s&s kit installed and my local shop explained the difference much as you did. The bigger cc seems to pay on dyno. Im running a stock 88 now and will let you know how it changes.
The 60ish hp it has now is pretty slow and disappointing. I did pipes and power commander then finally cams and its still needs more to be up to speed bike only 5 years newer.
The increase in bore is going to pay dividends in torque! A good cam with a compression bump is going to give you a serious horsepower boost! Best part is all that is a lot less expensive than a new bike you have something special when you're done.
What cams did you use ?
So how did the build turn out?
Last summer I upgraded to the S&S 100" and love it.
But, in 2018 I went with the Fueling 525 cams. Thinking about upgrading to the 543.
I just recently found this channel and find the information very helpful and straight forward.
Thank you, l really appreciate it! Welcome to the channel, let me know if you have any video suggestions you would like to see.
i like big inch, BUT, i want tall gearing, for maximum range. i love using big motors, running lazily, giving crazy range. so far my best was a 58mpg chopper, set up for touring, 6 gallon tanks. i want to see 65-70mpg. someday. so light weight bike, with suspension, but big motor, tall gears, and ride, i was once a 40k mile a year rider.
40K a year?! That's more than most cars see in 3 years!
I am glad I saw this video very informative. I am going with the S&S big bore sidewinder gear dive kit😎 wake up my old 88 twin cam.
Did you do it yet how is it ? I'm in the market chain tensioner just started rattling today !
Awesome content man. I have a ‘06 Dyna Lowrider with 88 TC engine. I’ve done full pipes, aftermarket air cleaner, and custom tune (Powervision Dynojet). With winter coming and having 36k miles on it, I’m gonna pull the cam cover off and see what’s going on in there. I’m leaning towards a 509 cam mid-low end cam since this is my “bitch around town bike.”
I am Low Rider guy myself, l love those bikes. You've got a good setup going on your bike. The front tensioner is easy to see but the back is a real pain. It's a good thing you're looking in on it with 36k.
What do you mean by "bitch around town bike? Do you putt around or do you like to go fast once in a while?
good explanation, I have an 89 fxr .. and I planned to put an 88tc on it .. and I see the advantage of reaching 98 in the future .. greetings ..
Why do you want to swap the Evo out of your FXR?
I was looking to do this with my 99 RK but there was no support for the MM fuel injection and I didn't really want to take out a system that was still functioning very well to retune it with a carb.
Sold that bike and got a 2014 FLHTP and did the normal Stage 1 upgrades and am very happy with it.
It's hard to find anyone that can tune the MM system, what tuner did you use on your 2014?
@@GixxerFoo Power Vision thru Fuel Moto. Did intake, new head pipe and used mufflers I already had. I had the urge to do cams but after this upgrade bike runs great and has all the power I need.
It's hard to beat FuelMoto, l ordered my dad's Power Vision through them for his Vrod. They have been great to work with, l love how they already put one of their in house developed maps on there.
There are several deals available doing the big bore kit, as of June 2022, that seem appealing. I have done the S&S 509G upgrade and am now considering whether to go with new cylinder heads or doing the bore. 97" is under $1,000 and 100" is just wee bit over that. My bike is a 2003 FLHTCI with 26,000 miles on it. I am willing to put another couple of thousand dollars into it just to increase reliability for a cross country trip. It has plenty of power and torque, for an old guy! I can do all of my own work. What do you think, new cylinder heads or the big bore kit?
Fuelmoto worked for me .right on on their support..
Those guys are awesome there! Best support out there I have found.
I own a 2002 Fat Boy TC88..great chanel and info. Keep up the great work. Subscribed 🤘🏻
Very nice! The 02 was the last year of the Timken bottom end too!
@@GixxerFoo, go to my page and check it out. I have Vance & Hines big shots and Arlen Ness Monster Sucker 🤘🏻
It's been 22 years since HD installed timkin bearings?? I think they forgot what they are for!@@GixxerFoo
Your have become a new go to. I really love your videos brother
I'm at 40,000 miles on my 2000 Heritage Softail twin cam 88 cam tensioners look brand new check them this spring
That's awesome! Not every 88 with spring tensioners will do that!
What changes would need to be made on a carbureted model being upgraded? Additionally, what oil cooling system do you recommend and can you do an explanation on the install? Love the vids bro!
Thank you! Each manufacturer will recommend a starting point for carb settings. Definently a jet kit and going richer, they are gonna need some fuel for sure. Harley oil coolers are really good, Jagg would be my choice in an aftermarket cooler. Jagg has coolers with thermostats and fans, those are really awesome setups.
Jag makes the Harley Coolers!!
Thank you so much for your videos im only a year into owning Harleys an love it. I have an stock like new 03 flht with 1600miles except for a full Reinheart exhaust that im looking to hope up and do away with the cam chain tensioner. Taking notes everytime i watch your videos
1600 miles on an 03? The cam chain tensioner system is really the only draw back on the 88. Once you get a hydraulic in there you're golden. I appreciate you're support on the channel!
@@GixxerFoo Stator and overheating?
@@shizuokaBLUES As for the stator, no problem. As for the overheating, it is an issue if the bike is driven in a traffic jam, but anyway, an air cooled motor likes continuous riding, so overheating is not even a concern if air flow is constant.
Omar Salgado well my stator melted this summer because of the insane heat and humidity (and exactly as you said -being caught in a traffic jam). But it was 18 years old and this is central Japan
🥵 so what do I expect eh?
I’ve never had an oil cooled engine before because my bikes have always been Yamahas or Suzuki’s built for these brutal summers. Live and learn.
Thanks for your comment.
As for bike as a non-investment I agree. My investments and savings are there to pay for things like this and that’s part of the joy of life if you are blessed enough to afford it.
But I will say that ....selling a made-in-Shizuoka Yamaha SR400 (single /40 year old design) for an older dyna with built-in issues WAS one of the stupider things I’ve ever done. I’ve gone from loving riding in the mountains to quietly dreading it. Will it break down YET AGAIN? Will it cost me another 1K or another 2K? What’s next -the starter? The main bearing ? The transmission bearing ?
I’ve realized that riding an older Harley is a hobby and should be your second or third bike. The first one or two being Japanese or newer harleys (and you have a serious garage and tools)
So I half agree with you and half can’t quite see due to the mistake I’ve made of listening to Harley fans
Who won’t objectively look at their bikes (out of loyalty and ego) and only encourage others to be more like them. But live and learn and be grateful for even having a beautiful old motorcycle , a luxury in and of itself. This I Know
Happy riding and cheers 🍻
@@shizuokaBLUES Such a sad thing, really. I think you bought a seriously trashed bike. I say this because I own two H-Ds, one since very brand new 2007 Sportster and a used 2005 Softail, which both have needed maintenance, one from abuse and the other from being stored almost seven years, but not tragic failures. Indeed, I can state that the abused one, the Sportster, has stood all the beating like a champ. I remember one day that I rode it for 14 continuous hours and it never hesitated. Indeed, the stator broke years later due to maintenance negligence. That's why I say you bought a very abused bike in the interior. But overall, if proper maintenance is done in time and form, the bikes are bulletproof, and though I own a couple, I'm not that of a fan, because I like other brands, including the Japanese sport bikes. I have to tell you that any bike will have its issues if abused and not maintained, including the Japanese ones, which I've seen broken down on the road.
Greetings.
Yup; that’s way I’m go’n - 🤠✊👍🏻👌 hd has the 4”cyls with steel liners that fit in the case spigots - they are for the 96 so you will have to hunt for pistons 4” stoke and rings for steel liners .
It's really not a bad deal at all, if you shop around you can get those kits a lot cheaper than advertised. RevZilla has S&S products a lot cheaper.
GixxerFoo ruclips.net/video/A1j1gQ5iaVM/видео.html
These will fit the 88 spigots and you can buy cyls together without pistons and rings $400
GixxerFoo right on ; I’ll check price ; but S&s @ $1500 is out my price range -
Yeah they aren't that much shopping around, retail price is high on S&S.
GixxerFoo I got a price on the pair of 4” cyls at Harley dealer for around . $450 . Add weisco pistons and rings another $300 I believe.
I was looking at the "S&S 100/110" POWER PACKAGE FOR 1999-2017 HARLEY-DAVIDSON BIG TWINS" for my 88". It has everything I think I need. Upgraded oil pump, cam plate, and I really like the gear cams over chain. What do you think of this upgrade?
That's an awesome package, the gear drive system is very dependent on the shaft run out being in spec,
.003 or less 😬. The gear drives are awesome and worry free, expensive upfront though.
@@GixxerFoo I would be hesitant going with gear drive cams on the twin cam 88 without upgrading to a new welded crankshaft or having the factory crankshaft trued and welded, I hear that even if the runout is within .003 that it may not stay there. I think I would feel uneasy about them on a stock crankshaft.
If the run out is within spec when it's installed l really haven't heard of many failures unless the run out just became atrocious. But by that time you've got some really serious issues.
I think I'll cancel all of my other RUclips subscriptions. You have got my attention.
😆😂👍 that's awesome! I still watch a lot of videos myself too, I like to compare opinions and see what others are doing as well too. Some I agree with and others I wanna know the who, what, when, why and how.
Really Enjoy the details you have in this video. Will you be making any more video on the Hammer Performance Products such as the 1275 kits with 560 or 570 cams.
I definently can, you add a cam to those big bore kits and that's really a power party.
I'd stay with the 95"... I like to leave room for improvement and rebuildability. Longevity is also a concern. Cost is another. At some point a S&S crate motor is better.
Not a bad idea, you can't beat that S&S motor. Those motors already have all the defects engineered out.
Those are some the coolest motors ever! They are literally true pan and shovels but with modern updates that you would never know are actually there.
Very good information. I enjoyed watching your videos. Keep up the good work.
Thank you very much! I really appreciate the support! We've had a major ice storm here in Oklahoma and I wasn't able to get another video this week. We'll be back next Friday for sure, but I a am hoping to get power back and get 2 videos for next week.
Love your channel brother.
Harley stock heads can't breathe for nothing ported heads will bring more life to your engine than you can ever imagine
That's been a serious draw back on the twin cam for sure. Also the low stock compression doesn't help either.
Im doing the S&S 100ci kit with 585 easy start cams. What would you recommend for jetting on a CV carb?
I'm thankful for you and your channel. I've owned a couple HD, s. Cut my teeth on the iron head, then I had a 93 Fatboy, EVO, s are fabulous little engines. I recently purchased a 06 Flhpi. Your channel has taught me about the TC and the options I have to choose from. Thanks brother
I would probably put an aftermarket crank in an 88 before I did any kind of major power increase.
That's pretty amazing hp for either kit, thanks for sharing this with us Brother, much appreciated 💯🤜🏼🤛🏼
It is pretty impressive, aftermarket kits makes some real power compared to Screamin Eagle.
@@GixxerFoo yeah that's one reason I was thinking about a Zipper kit on my 2017 with the 107ci , give me your honest opinion on what route you would go with the 107, I would appreciate it 💯👍🏼
I'm not really familiar with the Zippers Kit for the M8, but l would go with a bolt on 124 and a nice torque cam on the 107. The 4 valve head really opens a world of possibilities on those.
@@GixxerFoo thanks brother, I appreciate your input 💯🤜🏼🤛🏼
No problem, just watch the power numbers and the price. Especially with aftermarket kits, the right combination can really make some power even if it's smaller displacement.
Nice info, Thanks. Question: I just bought a 2003 FXST Carbed w/ hooker headers, want more power so what about this plan. I'm thinking of the S & S 100 ci kit, S & S super E carb, 585 cams ? and entire cam chest upgrade, head work also. Do you feel this a viable plan or am i missing something. I want power but still have a daily cruiser without having to wrench on it constantly. Thanks for your help in advance and Take Care Brother..
Great source of information. Thanks!
Thank you, l appreciate your support!
I have a Early production 04 Road King custom converted to a stripped Classic.
Carb motor CV 44 woods needle. SE manifold. S&S air cleaner back plate kit.
203 cams with Upgraded cam tensioner and cam plate & pump & bearings. I wanted to do heads however all the heads had too much running compression. SE ignition for cams and big bore kit. Now Harley has Factory ported heads that keep compression stock as 203 cams need to stay under 9.5 static .
I feel this is a good upgrade for 88 or 95 milled motors. I really comes on around 60 mph. However t don't do much hyw driving. I don't want to have to upgrade my starter as it is sensitive to hot starts sometimes. I'm running a oil filter billet cooler which looks cool lol. Any thoughts 💬💭
Thanks for video, will probably go Fuel Moto cause I need tensioners upgraded as well. Cheers
Yes that would be correct , but, on my 88 I’ve found that the kits only offer the basic kit, and, I’m kind of lost as to what I need to actually buy, and, I don’t want to order parts I don’t need. I honestly think I could manage the install, but, my mechanic ability Belgians to fail the order forms like; do I need a install kit, do I need new bearing , can I use my stock cam plate and oil pump, if I buy the 100 sidewinder do I need new valve springs, should I by new heads or send them out to be reworked, which parts should be installed first. I think a video explaining this on a 96 or a 88 would be a very informative video.
You can still use your stock heads with the 100 inch kit, even the stock cam if you wanted to. It just wouldn't take full advantage of the added displacement. Valve springs are really dependent on the cam you use, cam manufacturers will specify if you can run stock springs or if you need to upgrade. Just depends how aggressive the cam is, now replacing bearings is all a good idea with a build. The stock cam plates are fine, but a billet cam plate adds more support but isn't really necessary unless you really ride hard.
Thanks for the reply. I don’t trust the Harley guys and I really want to do this myself.
I don't blame you, l don't really like using shops either. I do everything myself unless it requires machining lol.
I have a 95 from an 88 and I need to do cams and heads
Got my 2000 softail with 95 SE and SS 509G. CANNOT find a dyno chart. All the 509 charts are for the 88.
Question...I have a 06 wide glide 88 efi. about 18k miles on it. I bought it used and don't know if it has work done other than what I can see. The shop that did the work has long closed and I cant seem to get any records. Screaming eagle pipes staggered and screaming eagle intake on it. I assume it must have gotten a tune. I would like to put on the SS 100 sidewinder kit that comes with cams for high torque. I really like the idea of 100 hp and 100 plus torque. I'm not a racer by any stretch just a cruiser but I'm kind of over my friends pulling away from me with their Road kings, Street glides and Road glides. I mean I am 100 pounds lighter right? So I also like the sound of the screaming eagle pipes on it (amazing sound) and don't really want to spend extra money on 2 into 1 exhaust if I can help it. How much torque would I be giving up to keep the exhaust? Is that ok or do I really need to change them? Also do I need new cam tensioners and an oil cooler for this upgrade? What would you do to kick it up to this decade without breaking the bank and also keep the reliability? Also do I need to also get the frame brace or replace the engine mounts if I add torque- or can the old frame handle it? And how much about would I have to pay in to get all this work done?
You wouldn't really give up much if anything with the SE exhaust of that era, with the factory header it's really the best of both worlds. You get the sound of a 2 into 2 with the power of a 2 into 1.
2006 Dyna already has the hydraulic tensioners, they only did that on the Dyna that year. The cases are basically 96 cases with a bore for 88 cylinders and the heads are what basically later became the heads of the 96. Great year for the dyna!
The 100 kit will drop and you'll want a good cam too, S&S 585 is a good Dyna cam or a Wood TW-555 is a killer Dyna cam.
Hard to say what it would cost but the 100 kit about 1200, figure about 3 to 400 for a cam. Labor l am ball parking 2,000. Gaskets, oil etc, 300, and a dyno tune about 3 to 400. Total ball park guess l would say ridiculously high 4500. But indy shop with a can tune maybe around 3500.
@@GixxerFoo Sorry for my ignorance but what is "indy shop with a can tune?" Also my bike got the heavy-duty fork springs and new Ledged shocks in the rear. It has not ever wobbled -had it up to 85 few times. In your opinion will the extra torque flex this Dyna frame and create a wobble?- I read stories about that possible wobble- I have no problem-but I do not want to create a problem either.
Excellent info - was looking for insight on the S&S 98 kit. Thanks!
I did the SS 97 inch and Delkron heads with Feuling camchest 90 hp 95 tq
Those are some pretty good numbers! What compression ratio did you go with?
@@GixxerFoo should be 10.1
What would you recommend for injectors for 100 hp harley motor
At 100 horse you're good with the stock injectors, once you start pushing the motor up over 110 that's when it's going to be time to start looking at a bit larger injector. Too big of an injector can do more harm than good, here's a video about injector sizing that explains more ruclips.net/video/PaiSNfnLfsc/видео.html
Can you give me a list of all the parts. Complete exhaust system , One hundred hot ride kit, Tuner.. What cams were put in the bike? Iam seaching for chop. Have 2010 ultra bone stock. Live in Darien WI so close for service. Looking for the exact same setup as this gentleman Ben. Please reply.
Thanks
Mark
the 98" kit is now 1280.00 from S&S
Question about Big Bore Kits and a stock clutch. I have a 2002 Softail Fatboy I want to put either a Fuel Moto 98" or the S & S 100" Power Package on and I will also replace my heads. By increasing hp and torque I should probably upgrade my clutch. Fuel Moto has a variable pressure clutch that supports 130Hp/130Tq with OEM spring. Should I try it with my original clutch first or just go ahead and do something with the clutch when I do the big bore kit and heads? What clutch upgrades should I do? I don't know much about what all is involved and will ask the mechanic that installs the other upgrades I mentioned his advice. I value your opinions and advice a great deal. Thanks!
Lol 11 degrees the other day... I think that's about my limit. Ty
11 degrees?! Yeah l think l am out on that too, bike will run cool though.
I want 100hp and I have a 88tc fatboy with 60k miles on it what do you recommend
You can get there with a bolt on 95 and using a Wood Cam. Depends on your year and if you're carb or fuel injection. Bump the compression to 10:1 with some mild head porting and it will bang out 100. 100 horse is a great number for Twin Cam, plenty of power and reliable.
I already encountered my first issue n the break in...may have a lil too much torque id like to believe...but honestly idk what happened..my pulley broke..all 5 screws..so ima drill n tap or "ez out" ....this thing is a monster...i ran down a stock m8 114 breakout ..i need a tune now. My ecm is locked with tts master pro...what can i donto start fresh get a new ecm..btw im the guy with the screaming eagle 103 with mild worked heads 543 reaper cams domed pistons fueling oil pump amd camplate...im unsure what to do next. I may be thinking too small...why not 124 if im have to crack the cases anyway..
Good day
Great Channel 👍
I am planning to get a play bike after 10 years out of the saddle my age is 65
My rides will be under 100 to 150 km.
I am mechanical inclined and built many metric sport bikes
Looking at my old favorite shovelhead or a newer Evo bike around 2005
What is you recommendation
Thanks in advance
I decided to go with the 98 S&S kit but i dont know what cams to go with can u help me out. Thanks
What compression are you looking at running?
I really cannot see adding all that work without having the crank trued and welded.
Having a stock 2000 FXDL with carburetor; not FI will my carb being re jetted support 100HP???
Oh yeah, with a proper carb kit installed 100 horse will be no problem. Even with just jetting changes it will support 100 horse.
Hey nice video I've watched 3x now lol wud.they 100 kit work well with 509 cams?
It would work very well with those cams, it's a bolt in and it will take advantage of the added displacement.
@@GixxerFoo thanks for reply. I split cases and up graded to timkens. Is a diff oil pump a must? Or factory one ok?
Can you put 103 jugs and pistons on the tc 88 ,and then cam swap to 510 so cam
The case bore is smaller on the 88 so the drop on jugs won't fit the 88. You'd need to go with 95 inch cylinders and then a stroker crank. The 100 inch drop on kit the biggest one out there for the 88 with the stock crank.
Question. I thought I heard you say the Fuel Moto cylinders had more cooling surface/fins early in your video, and then at the end you said S&S.
So did you misspeak? Do they both have that feature? Am I a poor listener? Lol
Thanks for the breakdown and information!
Hi, got a 03 electra glide standard, i want the S&S 100" sidewinder cylinder, will 103 SE heads fit to this set up ?? Runs S&S 509g cams
Yeah they will bolt up and they actually flow a lot better, even the stock 103 heads would be a big improvement. The 100" kit is made to work with the stock 88 heads so the 103 heads will bolt right on, you'll just have to use late model flanges on the intake. You can plug the ACR's or wire them to the starter solenoid, maybe put some manual ACR's in there if you want.
with the 100 inch Sidewinder bolt to a 88,
on do need to add a upgrade clutch?
It's never a bad idea to upgrade to heavier spring or centrifugal spring assist. A stock clutch with some miles on it may actually slip, especially depending how you ride. If you got the cash get a good clutch basket and go all out!
would you have any suggestions on a higher lift cams for a "06 FLHXI with the Harley 95" big bore kit installed, I run the Bassani true dual power curve exhaust with 4" Road Shark mufflers.
Thank you for a very valuable information 👍👍
Would it be possible to make a video about big bore kits for the 88” that DO require case machining and crankshaft work ?
Or , maybe even kits that offer new crankshaft, if there are any 🤔 ?!
How expensive would it get ?
Do you have to find a shop to do your machining locally or can you send your cases or even complete engine to those who offer the kits for a complete big bore overhaul?
Thanks
👌👍✌️
Not a bad idea, S&S and Zippers make serious kits with stroker cranks that you get to do a full case machining with. I believe with S&S they have a program where you can send your cases in, l know they do that with your heads.
So i called fuel moto about a big bore kit for my 88 tc . Bad news no. Kit available without compression release head work