Toro Recycler Lawn Mower Model 20334 - DIY Carburetor Repair Not Running Correctly - Nov. 11, 2016
HTML-код
- Опубликовано: 27 сен 2024
- This is a repair video on a Toro Recycler with electric start that just started barely running while cutting the lawn one day. It began revving up and down. This shows how to remove the carburetor and gas tank. Some small trash in the tank and carburetor cleaned that also replaced the rubber seat where the needle allows fuel to flow. Did a reassembly adding fresh fuel that has corrected this Electric Start Toro!
![DDG & G Herbo - Nosey [Official Video]](http://i.ytimg.com/vi/I9Ra0Zc2NlQ/mqdefault.jpg)
Great video. Followed this step by step today and my mower started on the first pull after I was done. Thank you for taking the time to make and post this.
Unlike most gas cans with ‘safety valves’, this one is EASY to operate ruclips.net/user/postUgkx6IImIpPboNrtVJSROnpF9EnyBzRrJKP_ with one hand. Nudge the tab and press the thumb button (all with your thumb) and you’re filling your tank. I bought this to use with a pressure washer that needs frequent refilling and it’s been a blessing compared to most of the ‘safety cans’ being sold. ergonomic and easy to handle.
The link brings me to the replacement tank for your rider mower. Do have a model number for the gas tank?
Thanks for the easy and clear instructions, you are the first mechanic that I found on you tube that doesn’t sound like I am going to disassemble a 747 airline engine and put it back together 😂. Thank you
Thanks, I was able to fix my old Toro lawnmower by taking it apart and cleaning the carburetor after watching your vid, works great now
You can try just removing and cleaning the carburetor bowl first, before you take off the entire carburetor. I found the bowl and its bolt to be quite dirty after a couple years of disuse. After a good brushing of the accumulated lacquer and cleaning the hole out in the 1/2" retaining bolt, my Toro started right up.
Good point
I'm gonna try that. Having problem starting the Toro - like, at all.
Really not looking forward to opening it up & repairing...
Hopefully with your approach, that's all my Toro needs to get going again. 😅
You just saved me $400! I have same mower. 2 days ago I was using it to chop up/bag leaves. It was working fine, I stopped it to empty the bag. When I restarted, it was revving up and down 4 or 5 times and would die. I checked gas and cleaned air filter, restarted and same thing. I was about to get in my truck to go to Home Depot to buy the Honda push mower (because I have 6" of fallen leaves to deal with). Something told me to check you tube and your video was the 2nd one I saw. I didn't have an overhaul kit, but I did remove and clean the carburetor (It was pretty dirty). Put it back together and it runs great again. Problem now is it's raining (alot). The leaves will have to wait until after Christmas. Thanks much for posting this.
Thanks for the video! I have a Toro lawnmower (7.25, 190cc) that wasn't working and stalling a lot. I wasn't sure about trying to remove the carburetor and cleaning it, but your video made things easy to understand. Thanks to you, my lawnmower is working again!
Very useful video with simple step by step instructions, to remove parts, clean and reassemble. Have an exactly same model Toro and had same problem. Fixed it perfectly by following your post. Greatly appreciate your post. Thanks.
Excellent video. Thanks for taking the time to do it. I was able to follow your instructions to the letter and got a great result. My first time exploring the insides of a carburetor 🙃
Hello First Last thanks for viewing! Really glad this helped you in a small way. Great job exploring the inside of a carburetor (kind of fun isn't it) and getting it going again!
Nice touch including the socket sizes. Useful. Each year I end up with a couple of used lawn mowers that people have given up on and discarded that are more or less just carb makeover/replacement away from having a full second life. I just got a nice hand me down Toro like this one in your video, and this was a good refresher video for me. Great job on the video. Plenty for me to use on here. I'll save it for future reference.
Great video - however groove side of needle seat faces DOWN (not up towards pin).
Put an inline fuel filter on. It doesn’t take too much dirt to clog up the jet. Most ride on
mowers have the filter, I am surprised push mowers are not factory equipped with a filter.
The Honda engines have a filter in the gas line that connects to the tank. It is in the fuel line and you can’t see it. I am surprised Briggs never did that.
Very nice instructional video by the way!
Hello Al Gorel! Thanks very much , yes agree with you Honda seems to be the only one they have fuel cut offs and a filter. The lawn mower type Kohler engines and Briggs and Stratton do not. Add a inline fuel filter and use non ethanol gas as well certainly would help!
thanks for your help. I corrected my Toro today and it is running much better.
Thanks, Again.
Nevermind. I figured it out...once I cleaned then off and realized they were different. The shallow one is an S2 square bit and the deeper one is a standard Phillips.
Thanks for your video. It helped me clean my first carburetor, and it started right up. 😃
You are a real magician ;)... To be able to fixe a machine like this... I'm impressed by your knowledge.
Nice easy fix, I can't believe how bad it ran in the beginning. I've watched so many of your videos that I'm wanting a Toro to replace my Victa now...lol
Thank you. , followed exactly and worked .thanks for informing what size socket to use. Love that. Thanks
You make it look so easy! Going to give it a try on my toro. Not fix/clean though, just purchase a new carburetor for ~$13.
the seat should go in with the groved side down actually.
Your first screw your took off the carburetor is a mixture screw and has holes in it that need to be cleaned thoroughly. it’s the number one problem in most mowers that causes start then stop, or low idle issues.
Purring like a kitten now .... Great work Cliff.
That bottom jet gets a little dirt in it and it wont run right. Thats what i usely clean out first with out pulling the carb completly off the engine.
this video really helped thanks
Hi Cliff, that Toro runs great now! I've never seen a seat swell up like that before, do you think it's the ethenol in the gas that caused it?
I like those toro mowers.
Perfect
Bull mowers ( toro) I like them.
my toro recyler leaks gas,so I changed the carb. and it still does it,seems the floats are sticking ,any advice?
Hi you use to comment a lot on my other channel, mowersandstuff this is my newer channel so perhaps you would like to have a look, lots of mower stuff on there. Hope your keeping well and still searching out them mowers🙂👍
Where did you buy the replacement kit. Having hard time to find the sealer seed
Do you know anything about fixing the personal pace on the lawn mower because mine is broken and I need to fix it
What size spark plug is that model
What did you use to clean the parts?
be very careful with those autochoke carbs the little piece that holds the vane can snap really easily.... what I have run into with a mower running like this can also be a slightly sheared flywheel key.... get job.
Thank you
... look for the obvious: small holes in a small brass 'jet' at the bottom of the gasoline bowl. The bowl and the jet plug should be physically cleaned and then flushed with solvent. You want any debris removed completely. Then reassemble and use only CLEAN, fresh fuel. A mower is not a car!
How did you clean it? What kind of product did you use to clean the carburetor?
You can use the stuff they have in the automotive stores. Works the same
Where did you purchase that kit at my lawn mower does the same thing and then when I’m cutting the grass it turns off on me
Hello thanks for viewing Jesus, got these on Ebay you can either get a package of just the carburetor seats or a single seat with a new needle. Sure Amazon would have something similar as well search for part # 398188 a very simple fix!
mountainbikekayak I have the toro 6.75 190cc model number 20352 do you think these parts will fit
Hi mountainbikekayak. I have the exact lawn mower model with electric start. I'm having the same exact thing happening now. The problem I have is the label for my lawn mower is missing due to mishap while cleaning with a pressure washer. I need to get the carburetor rebuild kit but I don't know the model of the Briggs & Stratton engine. If you could give me the numbers to that engine or the rebuild kit. I would really appreciate it. Thanks in advance. AW.
For Briggs and Stratton, the engine model number is stamped on the engine block. If memory serves its near the muffler but I’m not certain. I had to find mine to order some parts.
My electric start button isn't working pull handle starts it right up. I can hear a click when I push the button any ideas?
Charge or replace your battery.
Still a noisy mower. You'd think they'd have made these things quieter by now. Think I'll go electric when mine finally gives up the ghost.
Brilliant video, thanks so much for uploading. I have the 20956 Toro also with electric start and it's running poorly as yours was so I'll be servicing the carb as you did. Do you have a link to the carb service kit you bought and the small seat in particular? Thanks again.
Well 4 months later and I finally got around to fitting the rubber gasket as you very kindly showed in the video.......and my mower now runs like new. Thank you so much, you are a gentleman and a scholar!
I drained all the fuel and gave my carb a good cleaning an now it's reving way too high....I don't see a throttle adjusting screw on this style carb...where is that??? anyone know ??
Hello David thanks for viewing! One thing to check is to make sure the linkage is moving freely the butterfly is opening/ and no springs or the linkage are catching up under the cover. There is no screw adjustment on these newer type engines the speed is controlled by that fan on the flywheel which also should be moving freely as well. These carburetors can be bought new aftermarket type ones on Amazon or Ebay for under $12.00 as well. Have bought many of these and they work just fine if that carburetor is just sticking open.
@@mountainbikekayak Ok...thank you for your info...I really do appreciate it...I'll check the carb and linkages again... 👍
great vid..l subbed!
WTH, @3:08 is that electrical tape wrapped around the critical (n delicate) GOVERNOR SPRING !!?
7:19 "..now lets put the bowl on" with the rubber washer on the inside of the bowl or the outside? we'll never know.
nice video but you never really determined exactly what the problem was.
Thanks. Just fixed mine by watching your video
my recycler wouldnt start so i replaced the spark plug but that didn't do anything either so I decided to take it apart I removed the two covers to expose the flywheel and magneto the flywheel was covered with rust also the magneto so I wire brushed and sanded them, I removed the magneto and cleaned it up , then I clear coated it then I removed the cearcoat from the mating induction serfaces i did not clearcoat the flywheel and permanent magnet i then reinstalled the magneto using a business card to set the distance between the magneto and flywheel and tightened the magneto down reassembled the covers it started on first pull
great job
What did you use to clean the gas tank and carburetor? Also, if I want to insert a fuel line filter, do I need to cut the fuel line that goes into the carburetor?
Great video. I have the same mower and problem. your step by step process is easy to follow. Thank you
Buy a new carburetor... they are cheap
When removing the cover what type and size of bit did you use? I can't seem to find the right one.
What tools do I need in order to fix this?
First of all, many thanks for posting this great video! My Toro had the same symptoms and was able to follow the video to access the carburetor. However, I was concerned about the gaskets needing to be replaced so went to Amazon and found not only the gaskets but the entire carburetor for about $12! The only glitch I ran into was a small spring that I wasn't sure where it came off from and could not locate it in the RUclips. I took a chance and hooked it to where I thought it might go and now the Toro works like new!
...took a chance and hooked it to where I thought it might go...can you tell me where did the spring have to go in?
@@edwardfernandez7516 At 3:10 look at where his finger is, Just to the right is the spring I was referring to.
Mine is taken apart on a work bench right now, watched this video and I am fairly sure its the part that the linkage connects to on mine is stuck. It turns but with effort. If I cant clean it tomorrow prbably ordering a new carb.
Hello James thanks for viewing! These carburetors you can find new aftermarket ones on Ebay and or Amazon. The last spare I bought was just under $8.00 which is cheaper to replace than getting a rebuilt kit. Have used a number of them and they work just fine. This is the part number 799871 it you have a similar autochoke engine and decide to buy a new one.
What would wood shaving looking stuff in the carb bowl indicate?
Got carb on - no problem. Runs like a top! Thanks for your vid!
Great video👍
Wow nice video
Hello Freddie thanks for viewing! Been using this mower all year with no issues since cleaning that carburetor!
thank you very helpful
cheers