Great video. I have the same/similar plate and lift. I found the bolt to raise and lower the lift rubbed on the bottom of the plate and was a little "sloppy". So 3d printed a little wear cap to go over the head of the bolt. It reduced friction and stopped it grinding on the bottom of the plate.
Yes I have exactly the same perfect you don’t have to spend lots of money for router table and very good thanks my friend again I ready have push block table fence and know router lift thanks thanks again 👍👌👌
With smaller bits (i.e. 1/2 dovetail) the fence assembly can cover the lift screw. One might rotate the lift assembly 180 degrees and make a new hole for the crank in front.
I bought one of thee. Do u need to put some springs on the shafts bcos some ppl have said it moves/drops when ur in the middle of using this router lift. It's a good little lift but the issue I heard about has been spoken about by a few ppl now. Love the look of this mini router table though pal. Great build but all ur builds are tbf..
What was that composite material u used for the top? This really made it a nice finish in the end. I never bought the router plate when I should have but the lift is doing fine atm. I didn't put springs on it. I really like the blue colour table top with the GOLD colour plate.. It makes a nice finish to the top of the table. Keep up the great work pal.
The material call ACP (aluminum Composite Panel), this material very durable usually use for cover outdoor wall like mall or shop. glad if you think the result look good, THANK YOU very much
Hey, a few things to point out. I did buy the same kit, I'm planning to make a similar router table like this one. 1, It would be sensible to mark a midline for the fence to have a reference line to keep it straight. Also, I'd route out a groove for a ruler on both sides of the insert plate. The one on the plate is okay, but not for accurate work. 2, Safety first. This kit badly needs a starter pin and a hole to make it safe without the fence. 3, The mitre gauge is… sufficient, but there are better options. The T-track on the long side is suitable for the job, if accurate enough. 4, What is that pushstick? :D
Seems strange they would put the Router Raise/Lower Hex Bolt hole between the fences.. Why did they not put it in front of the fence where you could get to it easily? Ha..
@@mikewelch3903 Actually that is where most of the Chinese insert plates have the hole for the 'crank' ... The first Chinese designer did it that way and all the rest just copied his mistake. Original thought is not encourage among Chinese engineers and/or designers.
![[4K] Watch SpaceX Catch A Starship Rocket From Space!!! #IFT5](http://i.ytimg.com/vi/pIKI7y3DTXk/mqdefault.jpg)
Great video.
I have the same/similar plate and lift. I found the bolt to raise and lower the lift rubbed on the bottom of the plate and was a little "sloppy". So 3d printed a little wear cap to go over the head of the bolt. It reduced friction and stopped it grinding on the bottom of the plate.
Thanks for the info! i will use your idea!!
Yes I have exactly the same perfect you don’t have to spend lots of money for router table and very good thanks my friend again I ready have push block table fence and know router lift thanks thanks again 👍👌👌
Right on, your welcome my friend!!
With smaller bits (i.e. 1/2 dovetail) the fence assembly can cover the lift screw.
One might rotate the lift assembly 180 degrees and make a new hole for the crank in front.
Beautiful work, dude! Really well done! 😃
I'm definitely going to make something like that!
Stay safe there with your family! 🖖😊
Thanks a lot!
mantap bwang...
but router lift and base plate way too expensive for me, it's great idea for using ACP for top
thank you very much, happy hear that!!
I bought one of thee. Do u need to put some springs on the shafts bcos some ppl have said it moves/drops when ur in the middle of using this router lift. It's a good little lift but the issue I heard about has been spoken about by a few ppl now.
Love the look of this mini router table though pal. Great build but all ur builds are tbf..
I'm installing the same lift kit and added springs.
thank you very much!! sorry for late reply
what brand is the router table? (In Amazon Mexico I see one of Walfront) Is it good?
I forget, i add link on description you can check. For me this is enough.
What was that composite material u used for the top? This really made it a nice finish in the end. I never bought the router plate when I should have but the lift is doing fine atm. I didn't put springs on it.
I really like the blue colour table top with the GOLD colour plate.. It makes a nice finish to the top of the table. Keep up the great work pal.
The material call ACP (aluminum Composite Panel), this material very durable usually use for cover outdoor wall like mall or shop. glad if you think the result look good, THANK YOU very much
Hey, a few things to point out. I did buy the same kit, I'm planning to make a similar router table like this one.
1, It would be sensible to mark a midline for the fence to have a reference line to keep it straight. Also, I'd route out a groove for a ruler on both sides of the insert plate. The one on the plate is okay, but not for accurate work.
2, Safety first. This kit badly needs a starter pin and a hole to make it safe without the fence.
3, The mitre gauge is… sufficient, but there are better options. The T-track on the long side is suitable for the job, if accurate enough.
4, What is that pushstick? :D
Number 2: AFFIRMATIVE !!! (should not be difficult to add one).
Avid fan here of your useful videos from Manila. I've learned a lot. Are you from Indonesia or Philippines?
Thank you, i from indonesia. Glad if you learned a lot from this video☺
I was there in 2006, very nice!
I want this product
link buy in description
Seems strange they would put the Router Raise/Lower Hex Bolt hole between the fences.. Why did they not put it in front of the fence where you could get to it easily? Ha..
“They” didn’t put it between the fences. This guy did. I agree with you, he would have mounted it rotated 180º.
thank you very much!! sorry for late reply
@@mikewelch3903
Actually that is where most of the Chinese insert plates have the hole for the 'crank' ...
The first Chinese designer did it that way and all the rest just copied his mistake.
Original thought is not encourage among Chinese engineers and/or designers.
Hi Ok
Too much trouble for a beginner
agree, but if you can little improve this tool can work perfectly.