Try resetting the system by pulling the power heated seat fuse from the fuse box for a couple minutes then putting it back in sometimes that will reset the module. Also when you remove the wire harness from the Macho pay close attention for any burned or scorched electrical terminals in there sometimes those need to be repaired
Yes, it would light up for a few minutes then go out. Light would come back on after turning key off then back on. Further testing showed a break in the internal heating pad.
Mine wont switch on at all. The light for the seat button on the dash will blink and go off,niether seat works heat or cool. 2013 Expedition King Ranch
Mine do the same thing on a 2012 Nav. Has worked twice, when I bought it in June 2018 and sometime in Dec 2018, otherwise all lights come on and go out.
my seats will sound like they turn on and after a minute it will turn off and the light will flicker untill u restart the vehicle. this is for both seats. do u thinl its the module?
+Hatchet Mobile sorry it took so long to answer. I hesitate to say yes, because it didn't work for me. But worth a try if you can get the module cheaply.
Having hard time finding that info. One source says it's part of the fuse box on 07 up. I know the module with door code & security is behind passenger foot panel.
Hey! Ive got the same car (just 2013) and same problem... Could you hand me over the part code or something that I can use to get it? Or where can I buy it?
Part number is BU5Z-14C724-A, The one removed was 9U5T-14B663-AA, so I just changed my module you don't even need to remove the seat to change it took me less than 10 min to change it, my local dealer wanted 280 to change it and reprogram it which it didn't need. Good Luck
@@simpleinverso8628 No problem, a years after replacing it it stopped working again i thought it was the module again found out it was the wire connector that fried, had to replace that also...just a heads up
@@FlavesGarage I haven't changed it lol. But my cable is already burned and the module also got messed up... Thanks for the heads up! Now that the heat here in Mexico is getting unbearable, repairing it will come very handy!
there is a ground wire in the harness that you already know now to get too, unplug it and see if it's burnt then just bridge it avoiding having to buy a new one. get back to me and let me know.
Thanks for the video. im going to try this
Try resetting the system by pulling the power heated seat fuse from the fuse box for a couple minutes then putting it back in sometimes that will reset the module. Also when you remove the wire harness from the Macho pay close attention for any burned or scorched electrical terminals in there sometimes those need to be repaired
Did your heated seats switches light up when it wasn’t working thanks
Yes, it would light up for a few minutes then go out. Light would come back on after turning key off then back on. Further testing showed a break in the internal heating pad.
@@darylturcott My heated switch lights stayed on. Year ago the seat went out how the blower fan replaced. So maybe it’s another blower fan. thanks
Thanks for the info on how to get the blue connectors undone. Do you think the junkyard module could be bad?
Doubtful because the passenger seat still worked. Also I sold it on ebay and the purchaser never complained.
@@darylturcott Did you ever get it fixed?
what is the PART # on that module?
my drivers seat only doesnt work. think that makes it likely to NOT be the module on mine?
Kevin Goff mine is same, probably not module. You need to remove connector wire and examine it for burned contacts
daryl turcott mine is the same. Just removed the seat and no burn marks on ANY of the connections. None. Sooo now what???
Mine wont switch on at all. The light for the seat button on the dash will blink and go off,niether seat works heat or cool. 2013 Expedition King Ranch
I would definitely check the connector below passenger seat.
Mine do the same thing on a 2012 Nav. Has worked twice, when I bought it in June 2018 and sometime in Dec 2018, otherwise all lights come on and go out.
Quite likely the connector under passenger seat.
my seats will sound like they turn on and after a minute it will turn off and the light will flicker untill u restart the vehicle. this is for both seats. do u thinl its the module?
Hatchet Mobile it sounds like a module issue, since it affects both at once. Did you try pulling the fuse and letting the module reset?
+Hatchet Mobile sorry it took so long to answer. I hesitate to say yes, because it didn't work for me. But worth a try if you can get the module cheaply.
Hey boss do you know where the body control modulator is for a 2007 Ford Expedition appreciate it
Have to look it up when I get home after work. Might be under dash by right footwell.
thank you I appreciate it for taking the time
Having hard time finding that info. One source says it's part of the fuse box on 07 up. I know the module with door code & security is behind passenger foot panel.
@@darylturcott thank you sir I will take a look there I appreciate your time I'm sure information if I find it
Hey! Ive got the same car (just 2013) and same problem...
Could you hand me over the part code or something that I can use to get it?
Or where can I buy it?
Part number is BU5Z-14C724-A, The one removed was 9U5T-14B663-AA, so I just changed my module you don't even need to remove the seat to change it took me less than 10 min to change it, my local dealer wanted 280 to change it and reprogram it which it didn't need. Good Luck
@@FlavesGarage sorry for being so late, but thanks!
@@simpleinverso8628 No problem, a years after replacing it it stopped working again i thought it was the module again found out it was the wire connector that fried, had to replace that also...just a heads up
@@FlavesGarage I haven't changed it lol.
But my cable is already burned and the module also got messed up...
Thanks for the heads up!
Now that the heat here in Mexico is getting unbearable, repairing it will come very handy!
did you ever fix your seats?
Marvin St John no, haven't gad time to mess with it. Hoping to find replacement seat at junkyard
there is a ground wire in the harness that you already know now to get too, unplug it and see if it's burnt then just bridge it avoiding having to buy a new one. get back to me and let me know.
I should say that that was a problem, i'm not sure if they decided to go with a heavier gauge wire on your model but it's worth a look.
Marvin St John I will check it out and let you know.