Put tape over the pvc section you wish to cut should help with the splitting nasty edges. I would also fill the bar with concrete, it will make it heavier, stronger, and will help to prevent excessive bending.
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
Hey Keven! Love the new video, you are a really good actor with great instructions as always. My suggestion for a next one would be Concrete Dumbbells!
I was curious if you could do the same thing for a 1in barbell? I love seeing DIY content especially after coronavirus pandemic and the mark up of home gym equipment
Great video! I was wondering if the steel pipe could be filled with sand to decrease the bending on heavy load, then the sides could be sealed using steel stick.
I know that with rails on chain link fences, about 1 1/2" outside diameter they fill them with concrete for more strength so it may make sense here... I'm not sure about sand though ...
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
Hi Keven, I've wached one of your previous videos where you explain how to make concrete weight plates and the video is amazing and very useful, thanks! I have juste one question if you could help me, where did you buy the aluminium flashing used for the molds? I really can't find it in any store (maybe it's just hard to find in my country, Belgium) ... I've found it online but way too expensive (19€/meter). It would be very nice if you could help me
@@shadowarcherz i don't have a drill. Do you think i could use 1.75" pipe and hammer it over as the stop for the weights opposed to screwing in the 2" pipe? Or even layer a 1.75" then a 2" on top?
@@jimmorrisongrip6086 From what I researched around the interwebz there's a video of a guy using a black steel pipe sch 160 and it holds ~370lb fine without deforming (it's good that it bends at least a little, otherwise it'd probably break). Now, sch 160 is quite expensive, I ended up buying a used non olympic bar which can hold 500lb easy and was like U$25. It'll be more than enough for years to come.
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
Damn, this looks like the perfect solution at home. I'm new to anything gym based, but aren't these barbells supposed to weight like 20 kg (around 45 pounds) without weight? No criticsim, just curious if you have a way to get it. Thanks man!
I was thinking similar. The only way I could think to do it would be to fill the bar with something of substantial density, such as maybe sand, steel shot, etc. You'd need to have a way to plug the ends so whatever you fill with doesn't leave the side and also create a tight enough seal that whatever you plug with won't shoot out when the internal pressure gets high from dropping or excessive bending of the bar. Completely spitballing here, but maybe 12 inches of wooden dowel of just barely smaller diameter than that of the inside of the steel pipe, with adhesive in multiple circles along the length of the wooden dowel. Do that to each side and I think it would seal well enough against shooting out/losing the filler and still give you enough volume inside the pipe to add at least SOME weight.
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds and if you made the bar weigh 45 lbs it would defeat the purpose of it in the first place.
I built some…. It was expensive. Honestly I’m not even sure it was much cheaper then buying a set and for sure a hell of a lot more work. I’m not bashing the guide, it worked… it was just: expensive… and a fucking workout in itself…
Bullshit, I don't know what the hell is happening but I bought what you said and every tube enters freely in each other, no snug fit... I can't build shit with those loose as PVC pipes
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
![🟡 How to make 5 Kg. OLYMPIC DISC with CARDBOARD MOLDS [STEP BY STEP] 2022](/img/1.gif)
Amazinggg Keven can't findd a better video: Visual Effects - Entertainment - Fast and very Clear! Keep up the professional content💪🏻💪🏻
The Arnold impression had me in stitches mate lol fair play and great video 👍
Why didn't you continue uploading videos? Your material is very helpful and satisfying; I wish you come back some day.
Greetings from Mexico City.
Put tape over the pvc section you wish to cut should help with the splitting nasty edges. I would also fill the bar with concrete, it will make it heavier, stronger, and will help to prevent excessive bending.
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
good project, I was looking to make weights to train now in quarantine and this is a very good guide
If you were to put something in the middle of the bar for increase its resistance, what would you put?
Dude, savior!!
You just got a subscriber.
FUNNY AND LIVELY. KEEP DOIN IT SO. OH AND GOOD BUILD TOO!!!
Nice video man. Super helpful here because all gyms are closed due to pandemic
Hey what if we insert a 1/2 inches pipe inside the 3/4 in pipe.
Will it becomes more durable 😁?
Does it matter if you do not have any electrical saws?
I am from India . I like your video
could i use this for snatches and clean and jerks?
Hey Keven! Love the new video, you are a really good actor with great instructions as always. My suggestion for a next one would be Concrete Dumbbells!
this guy is literally so underrated
Yes
Hey man this video is sooooo helpfulll!! Its hilarious as well! Keep it uppppp WWWOOOOO 💕💕
Great video !
Nice mate. But how much weight can held?
Been waiting for a new video!
Awesome video! I was waiting for this :D
I was curious if you could do the same thing for a 1in barbell? I love seeing DIY content especially after coronavirus pandemic and the mark up of home gym equipment
Great video! I was wondering if the steel pipe could be filled with sand to decrease the bending on heavy load, then the sides could be sealed using steel stick.
I know that with rails on chain link fences, about 1 1/2" outside diameter they fill them with concrete for more strength so it may make sense here... I'm not sure about sand though ...
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
Thank you so much for this video.
Where can we find a steel pipe?...Thanks
Can you make some dumbbells please :)
Subscribed!❤️
I like him, he is funny and smart.
Maybe fill the pipe with concrete/rebar.
Wonderful
lets se that dead lift platform build ;)
Hi Keven, I've wached one of your previous videos where you explain how to make concrete weight plates and the video is amazing and very useful, thanks! I have juste one question if you could help me, where did you buy the aluminium flashing used for the molds? I really can't find it in any store (maybe it's just hard to find in my country, Belgium) ... I've found it online but way too expensive (19€/meter). It would be very nice if you could help me
😂😂😂I luv ur vib bro, you my man just nab ur self a subscriber 😂😂😂
I did it! My plates are nowhere near as pretty though. Thanks for the help!
Now teach us how to make those stone plates
How much do you think this thing costs?
What a legend
dumbells pls
In which country you live
bro make more videos jee ur good
How has it held up?
@@shadowarcherz i don't have a drill. Do you think i could use 1.75" pipe and hammer it over as the stop for the weights opposed to screwing in the 2" pipe? Or even layer a 1.75" then a 2" on top?
@@shadowarcherz will do 👍
@@shadowarcherz it did work i tagged you on instagram if you would like to see pictures/videos of it. Thank you have a great day
@@shadowarcherz thanks dude 👍
this guy is hilarious
Great video. What's the schedule of the galvanized steel pipe?
This is a secret, because it will bend even at 100 lbs))
@@jimmorrisongrip6086 From what I researched around the interwebz there's a video of a guy using a black steel pipe sch 160 and it holds ~370lb fine without deforming (it's good that it bends at least a little, otherwise it'd probably break). Now, sch 160 is quite expensive, I ended up buying a used non olympic bar which can hold 500lb easy and was like U$25. It'll be more than enough for years to come.
@@eucharistenjoyer Buddy, a bad barbell (neck) is better than a good pipe!l💪
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds.
Damn, this looks like the perfect solution at home. I'm new to anything gym based, but aren't these barbells supposed to weight like 20 kg (around 45 pounds) without weight? No criticsim, just curious if you have a way to get it. Thanks man!
I was thinking similar. The only way I could think to do it would be to fill the bar with something of substantial density, such as maybe sand, steel shot, etc. You'd need to have a way to plug the ends so whatever you fill with doesn't leave the side and also create a tight enough seal that whatever you plug with won't shoot out when the internal pressure gets high from dropping or excessive bending of the bar. Completely spitballing here, but maybe 12 inches of wooden dowel of just barely smaller diameter than that of the inside of the steel pipe, with adhesive in multiple circles along the length of the wooden dowel. Do that to each side and I think it would seal well enough against shooting out/losing the filler and still give you enough volume inside the pipe to add at least SOME weight.
I know I'm a little late here but the article is about making a training bar for people who can't use a 45 lb barbell. This wasn't meant to hold 100's of pounds and if you made the bar weigh 45 lbs it would defeat the purpose of it in the first place.
and howd you make a olympic barbell?
Great channel you got here. I just subscribed. Keep up the good work! 🙏🏼💪🏼
Btw what is your ethnicity?
@@shadowarcherz ey! Kifak khaye?
I thought lebanese or greek haha. Wish to visit lebanon some time soon.
Has somebody done this with European measurements?
😎🏆👌🏻
Nice tutorial, bro. Can you also include your total expenses for each project? I am wondering how much did this cost to build.
I built some…. It was expensive. Honestly I’m not even sure it was much cheaper then buying a set and for sure a hell of a lot more work.
I’m not bashing the guide, it worked… it was just: expensive… and a fucking workout in itself…
The meth lab had me rolling, I subscribed
TODAYS update on yuor equipment ? Cheap barbell GAS PIPE .
Try to make a diy cable machine my man...
Bullshit, I don't know what the hell is happening but I bought what you said and every tube enters freely in each other, no snug fit... I can't build shit with those loose as PVC pipes
this video quality eli’s absurd man
Very regular looking pencil😂
damn this dude is getting funnier
LOL I'm I the only one that noticed he came out of the closet??
What?
Edit: ah the intro
@@shadowarcherz haha I didn't think there was but I did find it hilarious