Secrets of pipe welding 2g

[@franciscogarciaromero5977]

Se parese a mi soldando con 7018 y acabado con 6013 muy bueno colega felicitaciones saludos dePeru

[@CarlosHernandez-ij7pl]

Tremendo tremendo trabajo 😊❤❤🎉

[@steelworkers78]

Nice welding tricks bro 💪💪💪 keep strong

[@gustavocardenas8843]

Hola q tipo de electrodo es?

[@juanzumaran6066]

Whats the amperage for each electrode(diameter information)and every pass..?

[@rishabsharma8702]

Hey I am a beginner is it possible to fill that gap with mig welding.

[@josevigil6731]

Did you only do 2 stringers and the one in the middle was your hot pass?

[@TheGoofyReview]

Too much inclination on the last rod. Try a 5° to 10° off 90° inclination. I do my 2G almost straight 90°. I use about 5° on the root and use a sawtooth weave

[@جمعهضاحيعبداللطيف]

رجاء شرح كيفيه ضبط الامبير لعمل مثل هذا اللحام

[@erikajanda3007]

What is Amphere you use on root pass, hot pass?

[@phillipwilliams7100]

Clean off the Millscale 1st....both inside and outside the pipe to even an inch....work clean ok..

[@hernanmoreira5455]

La raíz del minuto 1:36 pasa una placa? (RX).

[@luckyonyelonu964]

Please show how to weld 6gr please

[@luckyonyelonu964]

Thank you sir i love your tricks, PLEASE SIR i need you to show me how to weld 6GR please!

[@miltonandrescanar3145]

Tengo una duda la pulida es por los bordes de la soldadura

[@juanzumaran6066]

Si,en el borde de arriba..en cada pase...siempre la línea guía.. para tu próximo cordon, hasta k cierres tu bisel

[@ousmanecamara5188]

Excellent ❤technicien

[@peterkinzius7185]

Dans un premier temps en explication du jour,hagrafage est nickel mais dans un deuxième temps ce qui serait bien c'est que tu expliques l'orientation de ton électrode combien de degrés par rapport au metal.😅😅😅😅😅

[@michaelshortridge6379]

Can't see why he uses red 6010.5p+ or 6p+ weld way better.

[@TheUltimate65]

Weld stight sideways, then you not need to.use the grinder fore cut more opening under the weld

[@naydah]

Root pass seems to get too much amperage thats why melt is so deep - did you try like 10-15 amps less or smaller electrodes diameter ?

[@francisjamesbarroso387]

É 6010 o famoso 5p muito bom

[@shanmoore7838]

Too much undercut on last pass

[@점-p5c]

파이프 뚜께가 3티 정도되는. 개선 치지않고 용접하는 영상 부탁드립니다

[@tomasnunezcasal7964]

La pinza es la reina.mucho ahorro en gases..

[@YadavG-l1v]

Sukhmarkumai❤

[@idrisidris2300]

Mantap.. From indonesia

[@AhmedTarek-tw1ei]

معلش الماسورة ماتتبنطش خالص ركب عرايس رفيعة ولما توصلها اكسرها

[@KarimBenzema-z8m]

👍👍

[@내가누구게-l4m]

속 비드 가 완벽 하네요.굿~^^

[@rapperticotds8925]

Poderia soldar e explicar os passo a passo si comunicando com o publico e outra observação lixadeira sem proteção da merda em fixa a dica

[@PiotrMiskiewicz-oz8km]

Super,,

[@asmaezadin1961]

❤❤❤❤❤❤❤

[@lugokloe]

good

[@uraierasimov4581]

Паки боги сварочных дел.

[@DIDAR.2101]

Да, и у меня был бы на стройке кресло и отрезанная сварочная работа под рукой

[@rezazandi]

هزار ماشالا👏👏👏👏👏👏👏👏👏👏👏

[@francoresca5870]

Quello non è il 6010 , cos'è?

[@сергейдмитриев-ф3д]

. Кто будет зачищать околошовную зону ? И запилы делать на прихватки. Если бы перекрывал четверкой и двух проходов бы хватило. 159 труба стенка 8

[@ahmedizaguani9522]

Penitration 20%

[@bezen61]

😲👍

[@farshadRabbani-jj9ff]

احسن بهت👌👌

[@РустамКаримов-ь2ш]

В таком положении любой заварит

[@Владимир-у3з6э]

Я это делал 55лет назад

[@НОРТОЙ-р7у]

Удар чикди

[@internetalemi7773]

Он хорошыварин моладец

[@luckyonyelonu964]

Please teach 6gr with stick welding

[@boykaboyka2740]

Inclinazione dell'elettrodo sbagliata. La scoria passa davanti al bagno di fusione. I lembi non fondono bene. Pessima saldatura.

[@internetalemi7773]

Название корен 1 стик

[@SalohiddinxonKing]

💫👍👉🇺🇿👍👍

[@internetalemi7773]

Есть обратно валик

[@HamaduHassan-wy3up]

Malien

[@antemarov9422]

Good Work 👍👍👍