dell laptop 7 beeps no display । dell laptop 7 beeps on startup black screen
HTML-код
- Опубликовано: 22 авг 2024
- LAPTOP REPAIR ZONE. YOU CAN LEARN LAPTOP REPAIR FOR FREE.
FOR BIOS, SCHEMATICS, BOARD VIEW PLEASE JOIN OUR FACEBOOK GROPE : / 483833708998722
Excellent guuding
If voltages name could be in 1-line explaining, that's would be a bonus for us
Sir..dell inspiron 15 3521..no display with 7 low beeps just like a knock sound..pls advise
Sir, plz tell me what is the cost of this work you took from customer.
Hello!
I would like to ask you the following.
I have the same problem as the video, after checking and see that I have the same results as you, remove the transistor and instead of 15v I have 10v, I still do not put a new transistor so I do not know the result. I would like to know some recommendations. Thanks and very good work!
You can replace a new N-channel mosfet or you can short with jumper wire.thanks.
@@Laptop_repair_zone I have turned to you again. After changing the UZ1 and effectively, it gives me current in the indicated terminals, which did not happen before. However, instead of giving me +15 volts like at 5:25, it gives me 9-10 Volts, and the error persists. In the + VCC_CORE (6:05) does not give me any voltage, it stays at 0. Do you think you could give me some indication of what else to check or review ?. Greetings and good work.
@@Laptop_repair_zone kindly make a video on how to short with jumper wire
VERY GOOD. RESPECT
Thanks so much brother.
Every desktop, laptop motherboard has this 8 feet thing that looks like switching mosfet. Even graphics card board has it. Can I just get one from a motherboard and place on my Dell motherboard? Will it work?
Just replace a N-channel MOSFET thanks.
My laptop, firstly 5 beeps and no screen display. And one day, i cleaned RAM. Than I turn on my laptop give me 7 beeps and no screen display. I try turn on and than off about 5 times.
My laptop was succesfully boot without beeps sound
hie i have the same problem with the same motherboard you have fixed mine the +Vcc voltage is available everything is okay but its having 7 beeps no display can you assist me on that
dell 3531 beep 7 LA-B481p
Really great video. I followed all the way till u search for the voltages . The voltages on uz1 show ok... what can i do next ?
thanks for your comment, please follow the schematic diagram.
On my dell inspiron 5458, removing the battery and putting it back fixed this, this happens when i press the keyboard too hard
What is the name of the chip that you removed? What should I tell at Hardware store?
It’s a switching MOSFET .
Thank you so much, God bless you.
Thanks for your comment. please share my videos and channel.
THANK YOU SO MUCH
On my borad uz1 show 11.32 v instead 15 as shown.
One other legs it show 1.5.
No voltage on pl 701 and pl700
Please I have the same issue with my laptop. How do I contact you to resolve this issue?
Thank you . . .
where do i get the chip you change
Tnx sir
Thanks for your comment.
Hi. QZ1 and QZ7 only 0.71 voltages. Also power led is on. No fan .no display. What should I check?
Thankyou 🙏
Hello I am facing the same problem GFX CORE missing any Points to check
thanks for your comment.check +VCCSAP if present then check. +1.5VS ,+1.5V_CPU_VDDQ pu700. +1.5VS ,+1.5V_CPU_VDDQ
Hi, have same matherboard bat is going on 3sec and off all the voltage i have check and they are right whats the problem samone know;/? Super IO?.
شكرا لك
in my case heat up the processor do the job
help me i found 0V in PL600 and 0V in PL700, where is the problem
You can replace uz1 with 4430 helo me
In PL500 it is showing only 0.46 but in your multimeter it is showing 1.06
thanks for your comment, check or change pu500.
Best
Sir g cost?
ola ... minha medicao esta dando errado no mosfet 6644
so thanks
Thanks
Would you please help me dell 3 beep code fix
+VCCSAP is showing zero... Where might be the error
thanks for your comment,check pu600.
Pls provide sound on your content
Thanks for your comment
Sir instead of 15v there is only 11.25v showing (uz1) please advice me 🙏🙏
thanks for your comment, 11.25v its good enough,check +1.5VS is present or not,and follow the schematic diagram.
same to my board, i just chnage the capacitor and resistor close to uz1 and boom it display and vcc core power was present
Value resistence please friend@@wisdomugochukwu7742
Value resistence uz20
No voltage on PU700
No voltage on pu 700
Sir my dell 3521 beeps 7 times on battery, but works normally on charger
Thanks for your comment.check all the voltage with battery.
what is the value of the resistance uz20@@Laptop_repair_zone
Hello there, I have around +7V in +VCCP, not +1V as you're...Should I replace PL500?, thank you in advanced!!
+VCC_CORE also Not Present, all other voltages are ok, what should I replace for those two voltages not present, Thank You!!
Thanks for your comment, please reflow or change PU500.
Please join our Facebook group.
@@Laptop_repair_zone already did, thank you so much!!
Hi, I have Dell 3537 with the same problem, 7 Beeps, one laptop repairer told me to change motherboard, plz give me some suggestions.
you can follow this video.
Isn't the motherboard is same in Acer e1531 🤔
Hello Sir, I have an alienware 14 with the same problem ( 7beeps) but I can't find the UZ1 chip, any advice ?
Thanks for your comment, alienware 14 and dell inspiron 15 not same motherboard you need to check all the required voltage step by step.
@@Laptop_repair_zone do you maybe know which one is for the VCC Core on the alienware 14 main board?
please i need your help its the only laptop i have
What is the reason for five beeps for the same motherboard
Thanks for your comment. 5 beeps CIMOS battery, check your CIMOS battery.
hallo i remove UZ1 but i don't find 15 V what is solition plz ?
Thanks for your comment, please check out Dell inspiron 3521 LA-9104P no display, solved. ruclips.net/video/CFc2fGDJd8M/видео.html
NO
What will it costs?
For normal people it costs Around ₹2000 to ₹3000 at work shop.
But for technician it costs only ₹500/-
thank you sir
The switching mosfet in UZ1 has label on it but it's so small and scratched that I can't read. Can anyone help me with it?
SI4634DY bro
@@Tirkan Thanks. I removed the mosfet in UZ1 and motherboard is not making sound anymore. Cooling fan is working. Battery is charging but no display. My friend said that I must find exact mosfet to replace. Can I just get any mosfet that looks like it and place it? Will it work?
@@Tirkan motherboards and graphics cards have mosfet that looks like the one I removed from UZ1. can I try with any one or it have to be exactly same? I really don't know where to find this.
You have eBay?
You Must put the Same mosfet. If you found from another motherboard you can take it
no voice
Thanks for your comment.
Thanks sir
Thanks for your comment.