Stanley Meyer is up in heaven smiling for your having proved that his idea of using resonance is the way to go to generate a high amount of hydrogen from water.
What might be helpful is measuring the the volume of gas produced over time. Honestly, the gas production looks less at resonance, than at non-resonance. Hooking a gauge up to it, like Meyers did on his cell would prove it.
Interesting observation. I already experienced that, but this is basically what buck converters do. If your pulse is 50 percent on duty cycle you will see the double of amps on the cell in comparison to the input but the average voltage falls to half, and only at certain range of frequency (if you go to low the inductor saturates and you lose this effect). this is the pulse doubling effect (inductor discharging on the off time) and this is dependant on resistance of water (the LR transient effect, not LC).
It works. I have the same. Currently, i can get 6 times more amps then i put in.......amazing....still looking for a good way to make it a self runner.
I wish I could have 6 times the output. My setup is a little different, I have the same Water Fuel Cell setup as just about every Kiwi Fuel Cell Builder in Auckland, North Island of New Zealand and in the whole of Darwin, NT Australia. There are lots of Kient’s that build these devices. I use a Dual Petronix 60,000 Volt E-Core setup which in Series gives me a minimum of 120,000 Volts that oscillates at a base frequency of 270 Kilohertz which, I then Gate at LC Resonance. It’s powered by 200,000 Volts of Back-EMF Im-Pulses to the +Positive Anode during the LC Resonance ‘Coil Off’ Cycles. Then during the LC Resonance ‘Coil On’ Cycles I’ll pull Co-Valent Bond Electrons from the -Negative Cathode (Which is actually a ‘Time Reversed Re-Emitted Wave’ just like a Lightning Strike) which take the path of least resistance, which is through the Coil to a Spark Gap with Light Bulbs connected in Parallel, then this is connected to the +Positive Anode. If I didn’t have the Spark Gap & Lights I’d have little or no Deuterium H2 Output but, I have a Massive Deuterium H2 Output because I’m removing Co-Valent Bond Electrons from the Water itself. It works off High Voltage Tension & an effect in a Lightning Strike known as the ‘Electron Avalanche’ where I’d found that it only Works when charging the Water Fuel Cell with Back-EMF Im-Pulses!
I already own a 3.25 Kva GreenPower LPG Generator that has a Custom Exhaust Gas Recirculation (EGR) Beer Keg with an Ioniser in it. I’m already using in excess of 200,000 Volts to Knock Co-Valent Bond Electrons from Water using an Electron Avalanche. All I do is, switch my Circuit On, Reduce it’s Resistance to its Absolute Minimum, Dial into Resonance which is flicking a Switch having Dave Lawton’s original Phase Locked Loop (Auto-Resonance) Circuit. Then all I do is turn the Dial on my Variac Transformer until I’ve reached the desired amount of H2 Deuterium that I want for my Generator which is only 40 Volts DC. H2 Deuterium has Twice the Mass of regular H1. H1 Hydrogen is an Implosive Gas while H2 Deuterium being an Isotope of Hydrogen has Twice the Mass or more Ooomph in the Combustion Chamber because it is an Explosive Gas that Stanley Meyer refers to as ‘Thermal Explosive Energy’. I can actually power my Generator from H2 alone but I choose to combine 3X H2 Deuterium Atoms to 1X Nitrous Oxide Atom to form Ammonia Gas to power my 3.25 Kva Generator just out of tradition.
@@o5you86 I think maybe the problem with your setup is that you cant control the pulse frequency with a high voltage ignitor. Another issue is the driving power (amperage) available from such ignitors is negligible. The success of this experiment lies almost entirely in the electronics.
@@cjdonaldson8536 I’m not selling anything but, I reckon that its just Charging the Water Fuel Cell with Back-EMF Im-Pulses off any ignition coil or even a Tesla Coil. I think you need 80,000 Volts of Back-EMF Im-Pulses collected from the Negative of your Coils. You’ll know you’ve reach Resonance when your Coils Sing with a High Pitched Whine. I’m using a Variac rectified to DC with a 600 Volt IGBT switched with an Optocouple with a $50 USB Frequency Generator I got from Amazon. I just build my Cells 10X bigger than what I need then I overpower my Cells using 240 Volt Floating Earth setup with a 3.25 KVA Generator. All I’ll say is that I get about 5X the input with Lawtons Electron Extraction setup, just build & experiment yourself. I’m not out to prove anything as I’d had a Circuit Stolen from my 86 GTS on my front wheel cover & had insurance repair my driver side smashed window that is now a different colour to the other windows on my Car as I have a light Tint built into the Glass. Keep your SHIT to yourself & don’t Share as it can all be easily Stolen! Mates in Darwin use 44 Gallon Drum setups on Acreage collecting Electrons while discarding the HHO to the atmosphere. TRUST NO-ONE!
Stan meyer used AC voltage off of a pentium chip 3-4v pin voltage, 200 milliamps and a Phase of between 10mhz and 50mhz ,one specific phase released all the hho like a boiling kettle, if he moved the phase 0.05 mhz it stopped bubbling like mad with same voltage and amperage. Let me Clarify, He made the pins of the chip power the HHO bubbler.. so the chip would alternate Ground and Positive Voltage, in the 1/0 off the chipset. They he adjusted that chip from lowest MHZ to MAX somewher in there he found that phenomena of CFM per milliwatt , before that it was CFM per WATTS. Also his engine used the SONIC BOOM of HHO ignition ,as the Majority of the Combustion. This is why he made the Injector and Spark plug that GIANT unit. that went into the Plug hole, He needed the spark and oxyhydrogen millimeters from each other... IN THIS CASE..LEANER is BETTER, since he was not burning gasoline, IT would not suffer detonation near TDC ,and running lean would not kill the engine rings, and valves ,since the combustion temps do not soak in a gasoline engine, it runs so much cooler. Water vapor in exhaust steam cools the HOT side of the head.
Very good production, can you explain the details of resonance rod and size of WFC also any electrolyte if diluted in the water. Would you like to tell the details of PWM. Will be appreciated if answered. Regards
You dont need any details of his own every container every cell design has its unique capacitance all you have to do is to connect the right inductor and a PWM that's suits the frequency range of the self resonant frequency. There are bunch of online calculators online to calculate the resonance frequency. Make your own research
Note that the level of water decreases and the capacitance decreases too because of its dielectric property so you must adjust the frequency accordingly, or build your own self tuning circuit
Precisely Paul! The microcontroller gives the same effect as the burst of hydrogen when it's first turned on, in case anybody doesn't understand. I believe that only the few that graduated in the top echelon from Hudson Valley College with a degree in electronic engineering, would find it easy to grasp! LOL... If people would only learn and think!! Thanks. Joe Martin, class of '73
I've been studying this tech for maybe 11 years, not just Stan Meyers Waterfuelcell, in the case of Stan's first device the Waterfuelcell, it works on resonance frequency as you probably already know, I assume its the electronics are pulsing the tubes at the resonant frequency of water or resonant frequency of the pipes, but Stan Meyer moved on from this device, Why? Was it because the device would slip out of resonance? The great secret about this technology is about creating Electrically Expanded Water which can be created using the method you're using but also many other methods as I said there may be an issues with the device slipping out of resonance. The successful use of this technology, contrary to popular belief is not about releasing copious volumes of hydrogen in order to run an engine on water.
I use 498kHz, but interestingly, you can also achieve resonance at 1/4 and 1/2 this frequency. Also the pulses should be separated by a fully ON pulse width and not an OFF width. Outer cylinder should be negative and byfilar wound coil that is tuned to your capacitor setup. I will try and video my setup so far. The frequency is very hard to find due to so many variables. Great video you have, a pressure gauge and timed run would be perfect to show difference. :)
I think a little bit, the two pipes inside the electrolite is the capacitor ? If so, maybe a NANO VNA is usefully to find the so called resonance circuit. Thinking a little bit, the electrodes is in fact a capacitor. And a capacitor oppose to pure DC.
Why not make a variable frequency device so you can just turn the dial? The resonance will be on any of the natural frequency nodes of the vibrating system, there is no limit, this is basic electronics and basic acoustics. I would guess that the water would vibrate based on the volume, but there would be an ideal natural frequency where the least energy is required to fully vibrate the most water molecules.
@@jucavaque Thank you but a pwm modulator I can buy alone on ebay. What I am interesting is how to find the resonance frequency of rod and pipe to put them in together in resonance. On ebay wonn dont sell rod nor pipe.
So... the resonant frequecy is..? Or does that all depend on pipe diameter and length and getting the pipes to 'sing'? I see mention of 923 cycles per second (Hz) with no specific tube lengths or diameters in sight. Look up: Voltage:4,8 V Amp:300 mA Frequency: 923 cycles per second (Hz) (I'd post a link but it'd probably get deleted)
Fantastic video, I’ve been researching Stan myers for years. I have learned a lot in the past few weeks. Unfortunately I am not trained in electronics, but slowly understanding,unlike Wayne. Pleas humor my ignorance. How do you figure the number of windings on you resonant rod. And how would you control resonance if temperature or atmospheric pressure changes.
Its in relation to all of this , know that frequency is needed , i dont have it off top of head.. Yet have read about best frequencies to use.. so have a frequency ,generator ,tuned ,would make life easier .... Also , have 316L stainless steel due to corrosion resistance ... Which affects the frequency also. The voltage ,should be around 1.2. V between poles and not all are neg or pos , some neutral , So if you us3d a dry ,cell ,that the soloution passes , youd divide mayybe , 12v between the neutral plates ,to lower the voltage ,in each section ..to around 1.2v More voltage and current equals more heat , not a good thing ... Oh and for the bubbler /scrubber Maybe go look at delvis 11 video on hho He implemented a flash port , so the bubbler could not grenade !! An extra safety feature ,if you plan to use hho for burning ...
It gets too complicated because the dipoles of the electron clouds of the H and O are all moving and interacting. So you find the resonant frequency by charging it close to saturation, removing power, and measuring the frequency of the swing back of the dipoles. The resonant frequency will change depending on temp, pressure, and magnetism. So self adjusting using a type of phase lock loop would keep it in tune. Just have it skip a pulse every once in a while to have a micro controller keep it on freq.
hi. I just entering into hho production and still knowing Meyer's work but there is so much that it is not clear for me what is the latest work to implement. Can you provide any extra information to continue with? Do you have a blog, youtube channel or any social media to know your work? Thanks in advanced.
@@emesma Knowing electronics is a must. Everyone on the internet is wrong. Brute force is horribly inefficient. Meyer's patents are right. Read his words from all of them. He says voltage, no current. His circuit designs are very old school 1980's that's why many don't understand them. A fuel cell with distilled water is a capacitor. You want to charge the capacitor to just over it's break down voltage, but in a way that when the break down makes it conductive no more power flows, or it will just ignite the hydrogen you made. Look into how Geiger tubes work and the circuitry for them.
@@paulksycki I am in the rigth path then. The problem is, accourding to what I have found, Meyer's cirucuits are kind of modified with some "miswirings" to make difficult to people. I am still lookwing for the right one. And as I am also an old school electronic engineer, interprating the schematics is not a problem. Do you have corrected schematics? Thanks.
@@emesma Don't follow any website or video. Don't look at anyone's schematics except the one's in Meyer's patents. You need ALL of his patents google will give you. His circuit progresses with his patents. He explains the problems he over came and why he made changes. If you read his patents, easy efficient hydrogen he gave away freely to all with full explanation. .. I guess you didn't even notice his cold fusion patents LOL.He didn't call it that and it isn't technically "nuclear".. Those aren't so easy to understand and are not so perfectly explained. That is why he was murdered... Every fuel cell design will need custom circuit parameters. As I said research and understand every aspect of a "Geiger tube" and easy circuits to run them. Understand the "Townsend discharge" and concepts of how a Geiger tube works regarding "quenching", then compare to his circuits.
Two questions, did you use distilled water and did you electrically isolate the electrodes with some varnish or something else as stipulated by Stanley Meyer, in other words normal electrolysis does not work with his cells?
Hi. I live in the UK and I'm interested in constructing this device. The link to the instructions goes to a 404 page. Do you have another link? Thanks Bill.
Parece que se tiene que tener de un transformador un voltaje saliente por sobre los 50 voltios en una frecuencia por sobre los 5 khz y eso rectificarlo y cortar el amperaje con un generador de pulso
If it is working optimally you should only use milliampa. On half an amp is HUGE and you are just generating by electrolysis. I suppose you are getting some efficiency but I doubt that is over unity using 1/2 Amp;, again that is HUGE. Stan Meyer generated massive Hydrogen with a couple miliampss
Amps can't tell you anything without the voltage. Meyer was using high voltage. Volts x amps = watts 20 mA at 240 volts = 4.8 watts = 400mA at 12 volts Hope I did that math correctly
For those who are interested. I am creating a PDF document that will cover the details of the Resonant Rod Construction and how I use it and tune it to get the results in this video. This document will be available on EBAY for a fee. If you purchase the PWM in the description, then I will include the PDF at no additional cost. I will only be offering this to my subscribers for this week only. Please comment Purchased if you decide to do so:) Hope this helps you. Happy New Year to everyone!
@@thewonn Hello, I wanted to ask your question. Do you have an account on Instagram, email or WhatsApp? I wanted to communicate with you about a simple question about a project I have. Thank you
If one knows the capacity of water which is about 90, distilled and without an electrolyte and you want to achieve resonance you just solve for the inductor [residence rod] in Henry's at the voltage you use and Supply the inherent frequency. Not simple to idiots and those that have the Love of Money in their heart. LOL
UPDATE! We (WITTS MINISTRIES) are now getting 100Liters per second! that is 6000liters of Gas per min. That is 360,000Liters per hour! Input is only 497 Watts! No joke Search out our you tube channel and then our website for more details. We also teach you how to make your own simple fuel cell so you can be totally electrically, independent!
@@thewonn scam? how do you know that ? how big is their unit? What materials & technologies are they using? 100's of different hydrogen generator designs as is stands & probably a 1000 different (& more advanced) ways yet to be discovered ! & no doubt over time there will be advances
I use Dave Lawton’s PLL Circuit with 7 Cells & an Electron Extraction Circuit. 6 Watts puts out 8 Litres of HHO per Minute. The HHO is a +Positively Charged Deuterium Gas, then I’ll -Negatively Ionise the intake Air to Electrostatically bind with the Deuterium Gas then I use Purified Nitrous Oxide from the Exhaust to slow down the Burn Rate & Power a 3.25 KVA Generator... Lots of people in Darwin NT, Australia & they’re like Novelty Toys for these people!
@@thewonn I’d love to but I pulled it apart. ruclips.net/video/IViKuzX34xE/видео.html This is an old Video where I try to describe charging with Back-EMF IM-Pulses coming off a Dual Petronix 60 KV E-Core. I could replicate what you do using a 260 Volt Variac rectified to 130 Volts DC & a High Voltage Switch that switches a 120 Hz signal that is basically a Gate Circuit & the output would be 10 fold what you demonstrated using non Resonance. I’d love to show you what I have but I saving for an Apartment & don’t have time to do any HHO Stuff. Sometime in the Future after I’m living RICH I’ll upload an example of a Circuit using 100’s of Kilovolt’s of Back-EMF from a Petronix 60 KV E-Core Coil setup
Your need Back-EMF. Back in 2003 Kiwi Mates in Darwin revealed to me that the Effect is actually: ‘Tesla’s Phase Conjugate Mirror Effect’. If you take a Back-EMF Im-Pulse from a Coil & direct it to a Ground Connection ie: Copper Rod in the Ground, you’ll get a Bright White Light discharge of Electrons emanating from the Negative Earth, this effect is the same as a Lightning discharge where Electrons emanate from the Earth (See a slow Motion Time lapse of a Lightning Strike on RUclips). All you do is use an Isolation Toroid Coil then use Water as the source of Co-Valent Bond Electrons, then you Tune this into Resonance. I know Talk is Cheap but, Fracturing Water is really about the removal of Co-Valent Bond Electrons from the Water!
@ Blondie Bear You seem to jump from topic to topic, from your method to method, very confusing, indefinite, unproven, you want to show everyone, you don't want to show, you want to sell, you don't want to sell, you want the world to know about you ... everything confusing and indefinite.
@@OliverNedeljkovicZTI lol as far as i know everything i sell is available on www.fitnesshomesupplies.com My topics are what i am interested in at that time. I am not out to prove or disprove anything. I am just sharing my experiments. IF the right person or people want me to focus on any given topic, and they entice me , then maybe i can do that. For now, this is just a hobbie. I have many interests and obligations...
@@thewonn bro, are u telling that ur cell is capable of overunity? running at ambience temp? goin passed thru resistance of non-superconductive materials? or ur numbers are a measurement error due the alternancy of the AC circuit current in the LC resonant filter, cuz syntax error isnt an answer for me dude
hard to tell if there is any difference at all ! ....do a Liters per minute test one with the pwm and one without that will tell us more than the eye with the video ! .... Bob....
looks obvious to me. The first test you can clearly see that the hydrogen is not fogging up the container, and you can see the difference from the top view as well. In test one you can see the pipe from top view, in test 2 the top and container is filled with hho bubbles and foam. But yes I should measure it soon lol. Working on setting up more pipes first.
@@peterbuilttough3406 you’ll get killed if you try to patent your work, also if you do manage to create something great (like water powered vehicle), share it as far and quickly as possible
You need less power than you get its been known but hidden for a long time. Should be a able to use sound and light combined even tuned cavitation should be over unity.
Un poco confuso , en resonancia , los tubos se comportan como capacitores , cuyo dielectrico es , agua , y esta tiene que ser destilada o sea , no conductiva , fuera de resonancia , no tendria que haber produccion de gases, de lo contrario , el agua esta siendo conductora por impurezas en la misma o por el agregado de algun electrolito . Por lo antes dicho , no se entiende lo que haces , si es una celda electrolitica convencional o una con los principios de Meyer. Un abrazo.
Distilled water is a conductor. "Why is distilled water a conductor? Distilled water does conduct electricity. At room temperature, it contains 10-7 M each of H+ and OH-. These charged particles conduct electricity. Of course salty water, with many more ions, conducts better." - University of Illinois
@@VenturaIT .El agua destilada , sin rastros de impurezas , no es conductora electrica. A temperatura ambiente ??? , y en que afectaria la temperatura ambiente las relaciones H / OH en una molecula de agua ??? . Te equivocas , el agua esta constituida por moleculas polares de H2O , NO es una sopa de cationes y aniones H+ y OH- , NO HAY , electrones libres en la ultima capa de valencia , que permitan la conduccion , pues estos forman parte de un enlace quimico , covalente , no ionico , si no seria una sal. Justamente la adicion al agua de algunas sales la hace conductiva y por la generacion de iones libres .
@@fransinatra4474 You are confused, maybe due to the language. Distilled water is a conductor, just not a STRONG CONDUCTOR "Profile photo for Mayank Tanwar Mayank Tanwar · Follow Works at BatteryBhaicom5y Conductor and insulator are relative terms. Even common insulators can become conductors if the potential difference high enough. Think about lightning. Air is usually a pretty good insulator, but the high potential difference in lightning makes it into a conductor. Pure, distilled water is a very good insulator at relatively low voltages, even 110V AC. Some folks may never have actually investigated the conductivity of water. Tap water can be a good conductor due to calcium, magnesium, and carbonate ions, or other substances. But distilled water has no additional ions, except for H+ and OH-. The bottom line is that water itself is a poor conductor. Solutions of salts are good conductors."
@@fransinatra4474Also, at almost any temperature water evaporates (quickly or slowly), this means it is always giving off ions of H and O which will make it a conductor again.
Why isn’t there a more detailed explanation for all people instead of all these secret hints and whispers as if you’re afraid someone is going to become a millionaire from this and you would feel cheated? It’s too late for these games, let the cat out of the bag, let people know how make the Meyer style maximum hydrogen production, minimize amount of electricity used, let the whole world know how.p, let the oil companies out of business, boycott petroleum 💥💧💨🔥⚡️🌟
@@oahts5906 I haven't read the patents in a while and I only briefly went through them, but I can only imagine that anyone with a valuable invention would not put it all in the patent so it could be stolen, just enough to cover the main concepts to make the patent enforceable, not all the little details to make it work. So I'm just guessing.
@@VenturaIT you could be right about that, I’m not sure. I’ve only ever glanced at it. It looks thorough but some parts seem a little vague, so i can see why that’s the belief. This is a basic scientific principle, someone knows how it works out there.
I don't want to be persistent anymore and be a pain but you point me to your website and ut says out of stock. So I am a little confused On one hand I cannot order ut and on the other hand you send me to the video If you don't want to sell or share, I understand. But just tell me so I don't waste your ti.e The files that you link in your video descriptions, also need access. So either provide access or don't link to them. That's also confusing. I think you are undecided as to whether you want to share or to sell or not to do anything. Thank you regardless Uts your choice but make it clear to your followers so they don't bother you unnecessarily God bless you
![Kodak Black - Versatile 4 [Official Video]](http://i.ytimg.com/vi/VcP_1Ua__vY/mqdefault.jpg)
发明家是实实在在的人，视频记录内可以看到，十几年前就开始搞氢气和氧气的研究，十年后的今天，发明家现在还是再研究同一课题，十几年如一日，难得毅力精神，值得好好学习。
我支持发明家，会一直跟着发明家的脚步前行，
Does this mean the Chinese are aware of the disassociation between hydrogen and oxygen when resonating?Ahh Soo!
Stanley Meyer is up in heaven smiling for your having proved that his idea of using resonance is the way to go to generate a high amount of hydrogen from water.
What might be helpful is measuring the the volume of gas produced over time. Honestly, the gas production looks less at resonance, than at non-resonance. Hooking a gauge up to it, like Meyers did on his cell would prove it.
It really wouldn't though but sure
Impressive difference. Can you please collect the gas and try to measure the volumetric difference in production.....
I saw in a German documentary it can go up 14x more gas production by the same amount of currency.
Interesting observation. I already experienced that, but this is basically what buck converters do.
If your pulse is 50 percent on duty cycle you will see the double of amps on the cell in comparison to the input but the average voltage falls to half, and only at certain range of frequency (if you go to low the inductor saturates and you lose this effect). this is the pulse doubling effect (inductor discharging on the off time) and this is dependant on resistance of water (the LR transient effect, not LC).
isn't it parametric resonance amplifier ?
It works. I have the same. Currently, i can get 6 times more amps then i put in.......amazing....still looking for a good way to make it a self runner.
I wish I could have 6 times the output. My setup is a little different, I have the same Water Fuel Cell setup as just about every Kiwi Fuel Cell Builder in Auckland, North Island of New Zealand and in the whole of Darwin, NT Australia. There are lots of Kient’s that build these devices. I use a Dual Petronix 60,000 Volt E-Core setup which in Series gives me a minimum of 120,000 Volts that oscillates at a base frequency of 270 Kilohertz which, I then Gate at LC Resonance. It’s powered by 200,000 Volts of Back-EMF Im-Pulses to the +Positive Anode during the LC Resonance ‘Coil Off’ Cycles. Then during the LC Resonance ‘Coil On’ Cycles I’ll pull Co-Valent Bond Electrons from the -Negative Cathode (Which is actually a ‘Time Reversed Re-Emitted Wave’ just like a Lightning Strike) which take the path of least resistance, which is through the Coil to a Spark Gap with Light Bulbs connected in Parallel, then this is connected to the +Positive Anode. If I didn’t have the Spark Gap & Lights I’d have little or no Deuterium H2 Output but, I have a Massive Deuterium H2 Output because I’m removing Co-Valent Bond Electrons from the Water itself. It works off High Voltage Tension & an effect in a Lightning Strike known as the ‘Electron Avalanche’ where I’d found that it only Works when charging the Water Fuel Cell with Back-EMF Im-Pulses!
I already own a 3.25 Kva GreenPower LPG Generator that has a Custom Exhaust Gas Recirculation (EGR) Beer Keg with an Ioniser in it. I’m already using in excess of 200,000 Volts to Knock Co-Valent Bond Electrons from Water using an Electron Avalanche. All I do is, switch my Circuit On, Reduce it’s Resistance to its Absolute Minimum, Dial into Resonance which is flicking a Switch having Dave Lawton’s original Phase Locked Loop (Auto-Resonance) Circuit. Then all I do is turn the Dial on my Variac Transformer until I’ve reached the desired amount of H2 Deuterium that I want for my Generator which is only 40 Volts DC. H2 Deuterium has Twice the Mass of regular H1. H1 Hydrogen is an Implosive Gas while H2 Deuterium being an Isotope of Hydrogen has Twice the Mass or more Ooomph in the Combustion Chamber because it is an Explosive Gas that Stanley Meyer refers to as ‘Thermal Explosive Energy’. I can actually power my Generator from H2 alone but I choose to combine 3X H2 Deuterium Atoms to 1X Nitrous Oxide Atom to form Ammonia Gas to power my 3.25 Kva Generator just out of tradition.
@@o5you86 I think maybe the problem with your setup is that you cant control the pulse frequency with a high voltage ignitor. Another issue is the driving power (amperage) available from such ignitors is negligible. The success of this experiment lies almost entirely in the electronics.
@@o5you86 are you selling these or sharing the instructions
@@cjdonaldson8536 I’m not selling anything but, I reckon that its just Charging the Water Fuel Cell with Back-EMF Im-Pulses off any ignition coil or even a Tesla Coil. I think you need 80,000 Volts of Back-EMF Im-Pulses collected from the Negative of your Coils. You’ll know you’ve reach Resonance when your Coils Sing with a High Pitched Whine. I’m using a Variac rectified to DC with a 600 Volt IGBT switched with an Optocouple with a $50 USB Frequency Generator I got from Amazon. I just build my Cells 10X bigger than what I need then I overpower my Cells using 240 Volt Floating Earth setup with a 3.25 KVA Generator. All I’ll say is that I get about 5X the input with Lawtons Electron Extraction setup, just build & experiment yourself. I’m not out to prove anything as I’d had a Circuit Stolen from my 86 GTS on my front wheel cover & had insurance repair my driver side smashed window that is now a different colour to the other windows on my Car as I have a light Tint built into the Glass. Keep your SHIT to yourself & don’t Share as it can all be easily Stolen! Mates in Darwin use 44 Gallon Drum setups on Acreage collecting Electrons while discarding the HHO to the atmosphere. TRUST NO-ONE!
Stan meyer used AC voltage off of a pentium chip 3-4v pin voltage, 200 milliamps and a Phase of between 10mhz and 50mhz ,one specific phase released all the hho like a boiling kettle, if he moved the phase 0.05 mhz it stopped bubbling like mad with same voltage and amperage. Let me Clarify, He made the pins of the chip power the HHO bubbler.. so the chip would alternate Ground and Positive Voltage, in the 1/0 off the chipset.
They he adjusted that chip from lowest MHZ to MAX somewher in there he found that phenomena of CFM per milliwatt , before that it was CFM per WATTS.
Also his engine used the SONIC BOOM of HHO ignition ,as the Majority of the Combustion. This is why he made the Injector and Spark plug that GIANT unit. that went into the Plug hole, He needed the spark and oxyhydrogen millimeters from each other... IN THIS CASE..LEANER is BETTER, since he was not burning gasoline, IT would not suffer detonation near TDC ,and running lean would not kill the engine rings, and valves ,since the combustion temps do not soak in a gasoline engine, it runs so much cooler. Water vapor in exhaust steam cools the HOT side of the head.
What a good work. I have got questions. Have you found the solution to generate hho on high voltage and low current like what Stan did?
See Max Miller video " Stanely Meyer lecture" and he explains how resonance circuit is used to generate HHO.
Very good production, can you explain the details of resonance rod and size of WFC also any electrolyte if diluted in the water. Would you like to tell the details of PWM.
Will be appreciated if answered.
Regards
You dont need any details of his own every container every cell design has its unique capacitance all you have to do is to connect the right inductor and a PWM that's suits the frequency range of the self resonant frequency. There are bunch of online calculators online to calculate the resonance frequency. Make your own research
Note that the level of water decreases and the capacitance decreases too because of its dielectric property so you must adjust the frequency accordingly, or build your own self tuning circuit
How do you constrict the res,rod
Precisely Paul! The microcontroller gives the same effect as the burst of hydrogen when it's first turned on, in case anybody doesn't understand. I believe that only the few that graduated in the top echelon from Hudson Valley College with a degree in electronic engineering, would find it easy to grasp! LOL... If people would only learn and think!! Thanks. Joe Martin, class of '73
Yes! Trying at half an amp ! Good work.
Good current John! LOL
I've been studying this tech for maybe 11 years, not just Stan Meyers Waterfuelcell, in the case of Stan's first device the Waterfuelcell, it works on resonance frequency as you probably already know, I assume its the electronics are pulsing the tubes at the resonant frequency of water or resonant frequency of the pipes, but Stan Meyer moved on from this device, Why? Was it because the device would slip out of resonance? The great secret about this technology is about creating Electrically Expanded Water which can be created using the method you're using but also many other methods as I said there may be an issues with the device slipping out of resonance. The successful use of this technology, contrary to popular belief is not about releasing copious volumes of hydrogen in order to run an engine on water.
I use 498kHz, but interestingly, you can also achieve resonance at 1/4 and 1/2 this frequency. Also the pulses should be separated by a fully ON pulse width and not an OFF width. Outer cylinder should be negative and byfilar wound coil that is tuned to your capacitor setup. I will try and video my setup so far. The frequency is very hard to find due to so many variables. Great video you have, a pressure gauge and timed run would be perfect to show difference. :)
The capacitor is used how ? Parallel ? Series ?
I think a little bit, the two pipes inside the electrolite is the capacitor ? If so, maybe a NANO VNA is usefully to find the so called resonance circuit. Thinking a little bit, the electrodes is in fact a capacitor. And a capacitor oppose to pure DC.
Yes, so instead of AC current it’s a pulsed Dc current so a square wave vs sine wave
Why not make a variable frequency device so you can just turn the dial? The resonance will be on any of the natural frequency nodes of the vibrating system, there is no limit, this is basic electronics and basic acoustics. I would guess that the water would vibrate based on the volume, but there would be an ideal natural frequency where the least energy is required to fully vibrate the most water molecules.
Can someone point me in the direction to calculate a coil for a specific resonance. Thanks in advance
Thanks a lot for sharing this video. Can you explain please how you obtain the resonance ? Wich rod, frequency of pwm, type of signal, schematics?
@@jucavaque Thank you but a pwm modulator I can buy alone on ebay. What I am interesting is how to find the resonance frequency of rod and pipe to put them in together in resonance. On ebay wonn dont sell rod nor pipe.
So... the resonant frequecy is..? Or does that all depend on pipe diameter and length and getting the pipes to 'sing'?
I see mention of 923 cycles per second (Hz) with no specific tube lengths or diameters in sight.
Look up:
Voltage:4,8 V
Amp:300 mA
Frequency: 923 cycles per second (Hz)
(I'd post a link but it'd probably get deleted)
Fantastic video, I’ve been researching Stan myers for years. I have learned a lot in the past few weeks. Unfortunately I am not trained in electronics, but slowly understanding,unlike Wayne. Pleas humor my ignorance. How do you figure the number of windings on you resonant rod. And how would you control resonance if temperature or atmospheric pressure changes.
Its in relation to all of this , know that frequency is needed , i dont have it off top of head..
Yet have read about best frequencies to use.. so have a frequency ,generator ,tuned ,would make life easier ....
Also , have 316L stainless steel due to corrosion resistance ...
Which affects the frequency also.
The voltage ,should be around 1.2. V between poles and not all are neg or pos , some neutral ,
So if you us3d a dry ,cell ,that the soloution passes , youd divide mayybe , 12v between the neutral plates ,to lower the voltage ,in each section ..to around 1.2v
More voltage and current equals more heat , not a good thing ...
Oh and for the bubbler /scrubber
Maybe go look at delvis 11 video on hho
He implemented a flash port , so the bubbler could not grenade !! An extra safety feature ,if you plan to use hho for burning ...
It gets too complicated because the dipoles of the electron clouds of the H and O are all moving and interacting. So you find the resonant frequency by charging it close to saturation, removing power, and measuring the frequency of the swing back of the dipoles. The resonant frequency will change depending on temp, pressure, and magnetism. So self adjusting using a type of phase lock loop would keep it in tune. Just have it skip a pulse every once in a while to have a micro controller keep it on freq.
hi. I just entering into hho production and still knowing Meyer's work but there is so much that it is not clear for me what is the latest work to implement. Can you provide any extra information to continue with? Do you have a blog, youtube channel or any social media to know your work? Thanks in advanced.
@@emesma Knowing electronics is a must. Everyone on the internet is wrong. Brute force is horribly inefficient. Meyer's patents are right. Read his words from all of them. He says voltage, no current. His circuit designs are very old school 1980's that's why many don't understand them. A fuel cell with distilled water is a capacitor. You want to charge the capacitor to just over it's break down voltage, but in a way that when the break down makes it conductive no more power flows, or it will just ignite the hydrogen you made. Look into how Geiger tubes work and the circuitry for them.
@@paulksycki I am in the rigth path then. The problem is, accourding to what I have found, Meyer's cirucuits are kind of modified with some "miswirings" to make difficult to people. I am still lookwing for the right one. And as I am also an old school electronic engineer, interprating the schematics is not a problem. Do you have corrected schematics? Thanks.
@@emesma Don't follow any website or video. Don't look at anyone's schematics except the one's in Meyer's patents. You need ALL of his patents google will give you. His circuit progresses with his patents. He explains the problems he over came and why he made changes. If you read his patents, easy efficient hydrogen he gave away freely to all with full explanation. .. I guess you didn't even notice his cold fusion patents LOL.He didn't call it that and it isn't technically "nuclear".. Those aren't so easy to understand and are not so perfectly explained. That is why he was murdered... Every fuel cell design will need custom circuit parameters. As I said research and understand every aspect of a "Geiger tube" and easy circuits to run them. Understand the "Townsend discharge" and concepts of how a Geiger tube works regarding "quenching", then compare to his circuits.
@@paulksycki thanks. I really appreciate your help. I'll keep researching.
Two questions, did you use distilled water and did you electrically isolate the electrodes with some varnish or something else as stipulated by Stanley Meyer, in other words normal electrolysis does not work with his cells?
Tap water and electrolyte
@@thewonn hi sir
I think I saw Stan Meyer consuming 2mA, is it possible ?
Also go for the Skin Effect, and use only Graphite rods or sheets/ foil
Hi. I live in the UK and I'm interested in constructing this device. The link to the instructions goes to a 404 page. Do you have another link? Thanks Bill.
Hi. Did you find a way to get the instructions. Thanks
Can you show us how you made your coil
Hi, are you still selling instructions on how to do it?
Yes fitnesshomesupplies.com/collections/hho-hydrogen-products/products/pwm-hho-instructions
Are the actual volts the same going in, in both the examples?
Exactly. Amps alone is not enough. Watts=voltsxamps
2 volts plate to plate should be where you want be.
What is the price to buy the diagram for the PWM only?
How many wraps is the resonance rod ?
So when you say resonance, are you talking about using ultrasound at around 20 herz?
Hi, I ordered the plans. Do you have to ship it or is it a PDF? Hopefully I can get a PDF.
@gurpreetgill
did u get them delivered or was it a pdf?
Is the complete kit no longer for sale?
Parece que se tiene que tener de un transformador un voltaje saliente por sobre los 50 voltios en una frecuencia por sobre los 5 khz y eso rectificarlo y cortar el amperaje con un generador de pulso
Great job 👏✊👍👍😊
Please... what is the resonant frequency of water?
Thanks!
I BELIEVE YOU NEED TWO ONE FOR THE OXYGEN ONE FOR THE HYDROGEN BUT NOT SURE
41 khz
ruclips.net/video/XRgnWxAHxWA/видео.html
Very interesting!. What is the resonant frequency?
You dont need to know what frequency, it depends on your coil inductance and cell capacitance
Frequency varies much depending on your build up cell
Google series and parallel resonance
Usually 41 khz
Great info. Would a self resonating circuit work the same. If so do yo sell plans for it.
@@theodoresignal hi I only have plans for the HHO circuit and the don smith high voltage fast charging circuit
Thanks
Wow i want to build this,its awsome do you sell schematics of everything?
fitnesshomesupplies.com/collections/hho-hydrogen-products/products/pwm-hho-instructions
Very nice
If it is working optimally you should only use milliampa. On half an amp is HUGE and you are just generating by electrolysis. I suppose you are getting some efficiency but I doubt that is over unity using 1/2 Amp;, again that is HUGE. Stan Meyer generated massive Hydrogen with a couple miliampss
Have you build any prototype to confirm? I am really interested in HHO,. Do you have any web site to get information from? Thanks
Amps can't tell you anything without the voltage. Meyer was using high voltage. Volts x amps = watts
20 mA at 240 volts = 4.8 watts = 400mA at 12 volts
Hope I did that math correctly
i believe Stanley Meyers stated he also heated the water , some type of warmer he shows in his video .
Then how is the two spools of copper wire used ?
Hi
Is there anyway to get the circuit and coil diagrams and info from you!
Thank you
fitnesshomesupplies.com/collections/hho-hydrogen-products/products/pwm-hho-instructions
@@thewonn hi
Thanks for the love no but it says out of stock
Thank you
I guess if it’s a file or PDF how it can be out of stock?
@@Gacha.Cupcake emailed you.
@@thewonn thank you
God bless you
Email replied
@@thewonn thanks. Bought your product to help a little. God bless you. We all should backup good men like yourself. Thanks for all the hard work.
I can hear the high pitch frequency when you turned it on.
hi. your tubes have the same wall thickness? or are machined in a lathe for this? gap ?the outer is sloted?are annealed?
Yes, outer is 1" od, inner is 3/4" od. Seemless tubes off the shelf. 1/16" thickness.
nice work you still have the rods ?
Yes. They are required to get these results.
For those who are interested.
I am creating a PDF document that will cover the details of the Resonant Rod Construction and how I use it and tune it to get the results in this video. This document will be available on EBAY for a fee.
If you purchase the PWM in the description, then I will include the PDF at no additional cost. I will only be offering this to my subscribers for this week only. Please comment Purchased if you decide to do so:) Hope this helps you.
Happy New Year to everyone!
I’m interested. Can you share the link for eBay please.
Also I tried to buy the kit but the website is gone.
I’m interested
@@raulopatriot9034 fitnesshomesupplies.com/collections/hho-hydrogen-products/products/pwm-hho-instructions
Are you getting more out than you put in?
Do you have any electrolyte in the water?
You have two pipes in there? Can you describe your resonance? Thanks
Yes 2 pipes. One outer and one inner pipe.
friend what is the working attention of the transformer primary?
The information is not in the website. so sad!
Email thewonnhho@hotmail.com
Now how to apply this to a small home generator
Good...
How to make a 101 mhz resonance rod ? After the pwm . Hydrogen frecvency is 100.mhz for disociation and oxygen is 18 mhz
The frequency of a water molecule is 1.4 GHz.
do you sell the pwm also or where can we get from ?
I sell them here
fitnesshomesupplies.com/collections/hho-hydrogen-products/products/pwm-for-hho
@@thewonn Hello, I wanted to ask your question. Do you have an account on Instagram, email or WhatsApp? I wanted to communicate with you about a simple question about a project I have. Thank you
@@Mohammed-uz1snthewonnHHO@hotmail.com
hello, congratulations on the videos! you can talk about the components and connection system, I would like to make one like yours.
If one knows the capacity of water which is about 90, distilled and without an electrolyte and you want to achieve resonance you just solve for the inductor [residence rod] in Henry's at the voltage you use and Supply the inherent frequency. Not simple to idiots and those that have the Love of Money in their heart. LOL
what frequency are you running with the PWM?
Around 41 khz
UPDATE! We (WITTS MINISTRIES) are now getting 100Liters per second! that is 6000liters of Gas per min. That is 360,000Liters per hour!
Input is only 497 Watts!
No joke
Search out our you tube channel and then our website for more details.
We also teach you how to make your own simple fuel cell so you can be totally electrically, independent!
Scam
@@thewonn scam? how do you know that ?
how big is their unit?
What materials & technologies are they using?
100's of different hydrogen generator designs as is stands & probably a 1000 different (& more advanced) ways yet to be discovered !
& no doubt over time there will be advances
Is all you did was add the resonant transformer to it, Is it the standard 100 turns of bifiler 24 gauge wire.
I use Dave Lawton’s PLL Circuit with 7 Cells & an Electron Extraction Circuit. 6 Watts puts out 8 Litres of HHO per Minute. The HHO is a +Positively Charged Deuterium Gas, then I’ll -Negatively Ionise the intake Air to Electrostatically bind with the Deuterium Gas then I use Purified Nitrous Oxide from the Exhaust to slow down the Burn Rate & Power a 3.25 KVA Generator... Lots of people in Darwin NT, Australia & they’re like Novelty Toys for these people!
Talk is cheap - show us.
@@thewonn I’d love to but I pulled it apart. ruclips.net/video/IViKuzX34xE/видео.html This is an old Video where I try to describe charging with Back-EMF IM-Pulses coming off a Dual Petronix 60 KV E-Core. I could replicate what you do using a 260 Volt Variac rectified to 130 Volts DC & a High Voltage Switch that switches a 120 Hz signal that is basically a Gate Circuit & the output would be 10 fold what you demonstrated using non Resonance. I’d love to show you what I have but I saving for an Apartment & don’t have time to do any HHO Stuff. Sometime in the Future after I’m living RICH I’ll upload an example of a Circuit using 100’s of Kilovolt’s of Back-EMF from a Petronix 60 KV E-Core Coil setup
Your need Back-EMF. Back in 2003 Kiwi Mates in Darwin revealed to me that the Effect is actually: ‘Tesla’s Phase Conjugate Mirror Effect’. If you take a Back-EMF Im-Pulse from a Coil & direct it to a Ground Connection ie: Copper Rod in the Ground, you’ll get a Bright White Light discharge of Electrons emanating from the Negative Earth, this effect is the same as a Lightning discharge where Electrons emanate from the Earth (See a slow Motion Time lapse of a Lightning Strike on RUclips). All you do is use an Isolation Toroid Coil then use Water as the source of Co-Valent Bond Electrons, then you Tune this into Resonance. I know Talk is Cheap but, Fracturing Water is really about the removal of Co-Valent Bond Electrons from the Water!
@
Blondie Bear You seem to jump from topic to topic, from your method to method, very confusing, indefinite, unproven, you want to show everyone, you don't want to show, you want to sell, you don't want to sell, you want the world to know about you ... everything confusing and indefinite.
@@OliverNedeljkovicZTI lol as far as i know everything i sell is available on www.fitnesshomesupplies.com My topics are what i am interested in at that time. I am not out to prove or disprove anything. I am just sharing my experiments. IF the right person or people want me to focus on any given topic, and they entice me , then maybe i can do that. For now, this is just a hobbie. I have many interests and obligations...
So are you powering the cell by the coil. Hence resonating ?
Yes. Battery source to pwm, pwm to coil, coil to cell.
@@thewonn so your putting ac through the coil on the + side and where is your ground going?
@@off-gridhillbillystyle3735 complete plans are available here
www.ebay.com/itm/202868531009?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
@@thewonn bro, are u telling that ur cell is capable of overunity? running at ambience temp? goin passed thru resistance of non-superconductive materials? or ur numbers are a measurement error due the alternancy of the AC circuit current in the LC resonant filter, cuz syntax error isnt an answer for me dude
@@thewonn in the link i found now only signal generators, not plans, please have you got another link?
No diode as depicted in Meyers patent ?
no ever gauge
hard to tell if there is any difference at all ! ....do a Liters per minute test one with the pwm and one without that will tell us more than the eye with the video ! .... Bob....
looks obvious to me. The first test you can clearly see that the hydrogen is not fogging up the container, and you can see the difference from the top view as well. In test one you can see the pipe from top view, in test 2 the top and container is filled with hho bubbles and foam. But yes I should measure it soon lol. Working on setting up more pipes first.
@@thewonn how are ur measurements goin? do you figure something at all?
Ok
Can I run a car or a motorcycle with it 100% ?
For all of us half-wits, Is this a sustainable/ efficient method of powering a generator? This is fascinating to me.
Yes but more hydrogen is required
@@thewonn what are the draw backs?
I mean this seems like it could solve many issues that we're being faced with in today's world
@@peterbuilttough3406 you’ll get killed if you try to patent your work, also if you do manage to create something great (like water powered vehicle), share it as far and quickly as possible
You need less power than you get its been known but hidden for a long time.
Should be a able to use sound and light combined even tuned cavitation should be over unity.
Un poco confuso , en resonancia , los tubos se comportan como capacitores , cuyo dielectrico es , agua , y esta tiene que ser destilada o sea , no conductiva , fuera de resonancia , no tendria que haber produccion de gases, de lo contrario , el agua esta siendo conductora por impurezas en la misma o por el agregado de algun electrolito .
Por lo antes dicho , no se entiende lo que haces , si es una celda electrolitica convencional o una con los principios de Meyer.
Un abrazo.
Excelente comentario. Gracias.
Tienes mayor información de en donde puedo documentandome? Recién empiezo en esto.
Distilled water is a conductor.
"Why is distilled water a conductor?
Distilled water does conduct electricity. At room temperature, it contains 10-7 M each of H+ and OH-. These charged particles conduct electricity. Of course salty water, with many more ions, conducts better." - University of Illinois
@@VenturaIT .El agua destilada , sin rastros de impurezas , no es conductora electrica.
A temperatura ambiente ??? , y en que afectaria la temperatura ambiente las relaciones H / OH en una molecula de agua ??? .
Te equivocas , el agua esta constituida por moleculas polares de H2O , NO es una sopa de cationes y aniones H+ y OH- , NO HAY , electrones libres en la ultima capa de valencia , que permitan la conduccion , pues estos forman parte de un enlace quimico , covalente , no ionico , si no seria una sal.
Justamente la adicion al agua de algunas sales la hace conductiva y por la generacion de iones libres .
@@fransinatra4474 You are confused, maybe due to the language.
Distilled water is a conductor, just not a STRONG CONDUCTOR
"Profile photo for Mayank Tanwar
Mayank Tanwar
·
Follow
Works at BatteryBhaicom5y
Conductor and insulator are relative terms. Even common insulators can become conductors if the potential difference high enough. Think about lightning. Air is usually a pretty good insulator, but the high potential difference in lightning makes it into a conductor. Pure, distilled water is a very good insulator at relatively low voltages, even 110V AC.
Some folks may never have actually investigated the conductivity of water. Tap water can be a good conductor due to calcium, magnesium, and carbonate ions, or other substances. But distilled water has no additional ions, except for H+ and OH-. The bottom line is that water itself is a poor conductor. Solutions of salts are good conductors."
@@fransinatra4474Also, at almost any temperature water evaporates (quickly or slowly), this means it is always giving off ions of H and O which will make it a conductor again.
Why isn’t there a more detailed explanation for all people instead of all these secret hints and whispers as if you’re afraid someone is going to become a millionaire from this and you would feel cheated? It’s too late for these games, let the cat out of the bag, let people know how make the Meyer style maximum hydrogen production, minimize amount of electricity used, let the whole world know how.p, let the oil companies out of business, boycott petroleum 💥💧💨🔥⚡️🌟
Just look at the patent it’s available online
@@oahts5906 Pretty sure the patent is incomplete.
@@VenturaIT what is incomplete about it? The part people seem to miss is frequency resonance which is included in the patent
@@oahts5906 I haven't read the patents in a while and I only briefly went through them, but I can only imagine that anyone with a valuable invention would not put it all in the patent so it could be stolen, just enough to cover the main concepts to make the patent enforceable, not all the little details to make it work. So I'm just guessing.
@@VenturaIT you could be right about that, I’m not sure. I’ve only ever glanced at it. It looks thorough but some parts seem a little vague, so i can see why that’s the belief. This is a basic scientific principle, someone knows how it works out there.
I don't want to be persistent anymore and be a pain but you point me to your website and ut says out of stock.
So I am a little confused
On one hand I cannot order ut and on the other hand you send me to the video
If you don't want to sell or share, I understand. But just tell me so I don't waste your ti.e
The files that you link in your video descriptions, also need access. So either provide access or don't link to them. That's also confusing.
I think you are undecided as to whether you want to share or to sell or not to do anything.
Thank you regardless
Uts your choice but make it clear to your followers so they don't bother you unnecessarily
God bless you
Only resonant HHO plans are available for a $50 donation. Thanks
Hi. I would like to replicate your setup. Can you contact me please. Thank you