HVAC Tools List for New Technicians
HTML-код
- Опубликовано: 8 янв 2020
- In this video I go over a HVAC tools list and explain what tools are a must have for a beginner or an apprentice in the HVAC field. I also included recommended tools and optional tools that can make the job a lot easier. This list is a compilation of the tools I picked and the many suggestions of other technicians subscribed to my channel. The tools list is almost like a crash course of many of the tools you will see or need in the HVAC trade. Also, keep in mind that depending on what job you end up getting, your employer may provide all the tools that you will need. I talk more about that in the video. I hope all our new technicians and apprentices will find this video useful! And thank you to all those who contributed tool ideas!
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
➡️ Link to Amazon New Tech Tool List:
www.amazon.com/shop/wordofadv...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
For More Repair Videos:
🔌 Dryer Repair Playlist:
• Dryer Playlist
🧺 Washer Repair Playlist:
• Washer Playlist
🔥 Furnace Repair Playlist:
• Furnace Playlist
❄️ AC Repair Playlist:
• Air Conditioner Playlist
💧 Water Heater Playlist:
• Water Heater Playlist
🛠️ HVAC Tools Playlist:
• HVAC Tools
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🛒 For a Complete List of Tools and Parts Visit my Amazon Page:
amzn.to/2Q3QTOA
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🅿️ Want to Support This Channel? You can donate via PayPal:
www.paypal.com/cgi-bin/webscr...
👨💻 Or if You Believe Crypto is the Future:
Bitcoin: 3Lor4QqqExtScgkuHkNffJJksVXM5cq1mM
Ethereum: 0xb981484980b36d5d1b5d6574f3c5bfd73c19e13f
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🙋🏻♂️ Word of Advice TV Social Media:
Facebook ► / wordofadvicetv
Instagram ► / wordofadvicetv
Twitter ► / wordofadvicetv
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
📷 Interested in What Gear I use to Film my Videos?
Sony A6300 16-50mm: amzn.to/2OmLSPF
Sony 35mm Fixed Lense: amzn.to/2LPAU3A
Extra Batteries: amzn.to/3c8QBj1
Memory Card (2): amzn.to/34rcwQ1
60" Tripod: amzn.to/2mLXrU0
Bird-Eye View Tripod: amzn.to/3b3RWYy
Rode VideoMicro Microphone: amzn.to/2Ol9KDp
Rode Wireless Go Microphone: amzn.to/3ed5Wkv
Neewer Halo Light (2): amzn.to/2LTANUK
Viltrox LED Light Panel: amzn.to/39ZbSu4
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🙏 We would greatly appreciate it if you considered supporting our channel while shopping on Amazon by buying anything you need on Amazon after clicking on one of the links above. This gives us a small commission at no additional cost to you and helps us continue producing more videos! Thanks a million for your support!!
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
⚠️ Disclaimer:
This video is for educational purposes. All appliance and HVAC repair work should be done by a trained professional. Word of Advice TV is not responsible for any possible damages or injuries caused by the use or misuse of the provided information.
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
📥 SPONSORS / Collabs:
Would you like to partner with Word of Advice TV? 🤝
Email: WordofAdviceTV@gmail.com ✍️
Great information and the time travel joke made me laugh a little more than I should have 🤣🤣🤣🤣🤣🤣!
I’m at CD
The HVAC trade is a skilled trade. Very labor intensive. Very dirty. High pressure. Good luck. Especially as you age.
Name a trade that isn't. Quit crying.
This is everything you need to have your own business, great list.
Remember: As an apprentice you are not expected to have all this stuff starting out. As an installer I don’t use a lot of the tools he said to get like the sheet metal notching tool, just use your snips to notch it and save the money and weight for your self. Most guys just use needle nose pliers to open up the copper to fit copper inside of it. Not proper but it saves you from carrying around a lot of extra stuff.
I agree duke you don’t need every single tool especially if you do more research you’ll soon find out
Most of the expensive tools, company will supplies they only really expect you to have hand tools and gauges. Companies don't expect a tech to have a vacuum pump, scales and recovery machine. But it's a pretty good list of tools that people should be familiar with for sure.
Cool to see the differences between the US and Canada.
In Canada we are called refrigeratoration mechanics but they also work on heating systems.
Our apprenticeship is 4 years consisting of 1600hours per year on the job and 8 weeks technical training per year.
In Alberta we get an allowance of about $500 per week while we attend technical training.
It's a red seal trade meaning if you pass the red seal test after your final year of technical training, it's a certification that is recognized world wide.
One of the best videos on tools. I actually used it in my class to introduce my students to the tools of the trade. GREAT VIDEO. THE BEST. THE BEST VIDEO. ++++++++++++++
I cannot overstate how much I love the Klein HVAC 8-in-1 takes the place of the 11-in-1, it's rare for me to use torx or square, but the 8 has a core tool and stat screwdriver
Klein 2 in 1 nut driver 1/4 & 5/16, and Milwaukee M12 fuel impact driver are by far my favorite tools in my bag.
Malco flippable 1/4 5/16 nut driver is superior plus the Klien multiple size but driver is better for more. Not to mention just buying a set of imperial (us) nut drivers with various sizes.
Thank you both for mentioning your favorite nut drivers!! I think they are both wonderful! :)
Same bro I just got the m12 fuel surge
As a new tech just starting this channel was great for me to learn. Even now with almost 2 years of being in the field I still enjoy watching all these videos it a great way to keep refreshing my mind and I seem to always learn something new. Thanks for all the videos and all your help, keep up the good work. Oh... happy 100,000 subs!!!
Going to school for HVAC, these videos are very helpful.
Glad to hear the videos are helpful! Thank you for watching and leaving a comment!
Ҟrelay testing óhm certificate
@@WordofAdviceTV sir can i buy irvin visegrip adjustable because creacent is not availble in my country
Should i go with irvin or any other brand like taparia stanly etc
Go to college and get a career
Solved a bad circuit board that would cause blower fan to stop during an AC cycle and freeze up my condenser because of this channel. More recently I replaced the ignitor on my furnace because of this channel. Best RUclips channel hands down.
To any new technician or even the veterans nylog blue is not only for your manifold hoses you can use them on mini split flares. One of the best things ever
Wow. I consider myself an HVAC hobbyist, yet I have all the tools in one form or another except the anemometer (I have the fieldpiece manometer tho) and gas analyzer - the latter simply because I would never work on the gas metering myself. A lot of tools carried over from my other 'hobbies' plumbing, auto mechanics, gas welding, and electrical.
Things I don't have but would eventually like: iron pipe threader and cutter. I grew up on grandaddy's farm and was put to work right after school, he also had a trailer/rv camp grounds on the lake so got into HVAC in 5th grade working on mobile home hvac. Age 50 now with more decades of 'hobby' experience.
for those starting out, recommend you check craigslist for HVAC guys who are retiring and selling their tools
did i miss nitrogen flow meter, core removers? fireproof fiberglass canvas for brazing? sheet metal breaks and folding tools, circle cutter, crimpers...
Just added some to my Amazon wish list and they are coming for Christmas, thank you Jay!
I have learned so much from watching your videos. Will be starting my HVAC IN JANUARY thank you for putting this videos
Rafael
This was amazing video. I have got alot of these while I'm in school but I guess I still need quite a bit.
Best tape measure: Stanley fat max 25”, the Kobalt one at Lowe’s was good and a lot of guys like the DeWalt tape measure too. I like to have one magnetic and one not magnetic. Cheap tape measures the Walmart one or craftsman (Lowe’s) can get you by for a quick measurement but you will end up throwing it away.
Very interesting. The biggest thing I would say is: It depends on where one lives! In my area, southwest desert 🏜 you will not use most of you suggestions. Also Buy Quality to start with, it's your profession. I also would stay away from UEI and the "no name" tools. My 25+ year experience.
Extremely helpful! Thank u bro, u have great content and for someone starting out in school in an accelerated program and will be done in 6 months this stuff really helps along with your entire channel. I def appreciate the tips and videos u share
Starting hvac school this month your videos are great! Thanks for the content/advice
How’s HVAC going?
You are such a natural behind the camera. Your videos are first rate.
Nice video! My employer pays 50% of my tools cost 😎 Racking up the bill already.
Must be nice...
@@tmo2798 right 😂
Thanks. Just startimg out. Looking the the Backpacks!!
Pretty good advice and list! Thanks Jay! Stay awesome brother!
Thank you!! I will try my best to stay awesome and hope you do the same! ;)
Honestly I took all the pipe wrenches off my truck and use the knipex cobra in place of the pipe wrenches.
Got a hair less than 3 years and all 3 years I have been directly trained by a guy with 30 years of experience
Slowly building my tool bag
Anyways a few cool tools of mind is a “ swedge tool “ negates having to buy copper fitting saving ALOT of money per job
And another is a copper bender to keep from buying copper elbows n such when they run here about 15$ a piece
Great list! Insulated screwdrivers, lockout cap screwdrivers, clamp for door switch. I like Milwaukee for some hand tools which is close to prices. Wireless gages are less invasive but expensive. Indestructible shoes. They’re construction toed running shoes.
Very good video. wish i saw this video when I started working hvac.
Veto tp4b is a great back for service techs.. there are several videos to show how to load them out. Open top helps you not loose tools! I also agree that knipex by far had the best pliers on the market. I’ve switched over to snap on for some of my screw drivers, and 1/4 swivel head ratchet! Great video, also a cps solenoid magnet is a helpful tool!
Both, the tool bag and the cps solenoid magnet suggestions are great!! Thank you! I added both of them to the list.
Congrats on the upcoming 100k subs Jay.. awesome video as usual sir and as always, stay safe out in the hvac field.. 👍👍👍
Thank you good sir!! :)
needed required tools to start hvac school. this vid saved my life
Awesome video man, only recommendation I have is a mini split service valve adapter for your gauge hoses. And thanks for taking the time to construct this list, I can vouch for 90% of these and plan on grabbing the other 10% after watching this. Well done 👍
Thank you! I appreciate the add suggestion as well! I was looking on Amazon and am having a hard time finding mini split adapters that have high reviews. Do you by chance know which brand is good? Or an Amazon link would be good too. I rarely work on mini-splits so I don't have an adapter like that.
Thanks for looking out.
@@WordofAdviceTV really difficult to gauge an honest review sometimes on amazon. apparently alot of companies give out free product for an "honest review." Love your videos btw
The malco 5/16 +1/4 flippable bit is friggin awesome
I can only agree! That little thing is great!!!
Dam I figured I'd check out this video I been doing sheet metal for 17 years and I can say I literally have every single one of these tools so spot on, he didn't get into sheet metal tools though
I would recommend asking your boss to bill the sawzall blades, utility knife blades, and other small stuff to the job. Most places I work at is fine with it so you are not spending your own money on blades and using that money to buy better quality tools
Great video! Thanks for taking the time to create this. You're cool! BTW love your accent man. Keep up the great work and videos!
You're welcome! Thank you for watching and glad you enjoy the accent! I will try my best to keep the good content coming :)
I found Grainger and Zoro to also be good tool sources for trade tools. Thanks for passing along all your great knowledge.
Pretty much spot on.I would just add Fieldpiece or Testo smart probes and Harbor Freight pliars by Doyle.Thanks for the great video.
Awesome list, appreciate you taking the time putting it together. By the way in case you haven't seen them already malco released a 5/16-3/8 bit series at the beginning of the year. My supply house is already just about sold out for the first order.
I will promptly add that to the list! :) Thank you for the reminder! Sounds like it's a pretty popular one.
Thank you Jay. Explained very well. Very helpful.
3. Check garage, yard, patio or estate sales for tool deals. Keep a list in your wallet or purse.
4. Look for advertisements such as retired plumber, electrician, hvac guy . Not only can you get a good deal on tools, but veteran tradesmen like to help out new guys coming into the trades with tools and advice.
Great vid, can’t go wrong with the Klein hand tools!! Veto makes the best tool bags, they’re backpack is killer! Small note, the orange handled crescent wrench is too small for a lot of the low side king valve caps!! But definitely recommend a rubber handle crescent wrench, those things get blazing hot when sitting out!
That stubby Klein screwdriver is a lifesaver (mines Milwaukee and ratcheting idk if the Klein is but same thing) seriously a must have also the Milwaukee bit kit and the color coded hex set are as well. And of course a good Impact/Drill set is a necessity i use Makita but Dewalt Milwaukee and Ridgid are great too and a duct knife Malco is nice cos the soft sheath but Milwaukee and Hilmor are nice too.
Also a refrigeration unlock key so you can hook your gauges to the lines if they have locks on them and a rubber mallet.
EDIT:That was a really good list you covered all the basic tools for beginners.
I still enjoy your videos even though I think I’ve decided on being an electrician!
Glad to hear you are still with us and enjoying the videos! When I went to school for HVAC, my other choice was an electrician too! They are both nice trades. Good luck as an electrician!! When you have an Electrician Channel, I will subscribe :)
You should fix the problem if it's electrical. Don't be so 'categorical', you could make way more $. The evac kit could be a good compliment when you know the nooks and crannies. ... You're young. You'll find out.
Few different ideas I use:
Nut Driver set from Ace Hardware or Harbor Freight..However i only keep the 1/4" and 5/16" in bag and use a 18" extension with a set of magnetic nut drivers from Dewalt (Dewalt is skinnier than Malco but are not flip bits however have a strong magnetic hold - I don't carry long nut drivers since this is a dual use tool) Also just my opinion Malco sells the best Aviation- L/R Snips. Also if your doing Installs you will need a Hammer Drill to bore in stucco and concrete with the anchors - Sheet metal hammer all are Must Haves! Also if your going service you will need a Pigtail alot of time there are not convenience outlets (Don't get stuck on a roof without a way to plug in your vacuum or Recovery units) Since they are around $20 it will save your life! I totally agree with you in regards to pliers Knipex are the way to go ( I have both pliers with button and without I use the ones without more since you can adjust them very easy one handed) I also think you should add Scrub towels as you don't want to have dirty marks on walls from dirty hands ( also they remove blood if you cut yourself and didn't notice and touch a wall) I also believe all techs should have 2 meters as you will run into issues if you only have one (back ups are always recommended) Just another thought if you buy cheap tools you will have to replace them more often so if you can afford them buy name brand as they will last and think of it this way ..your making your living with these - if you cheap out your will have to work harder to get the job done..And don't let my name fool you I'm not really a Rookie..lol
Wow! That was a comment LOADED with useful information! As I was reading it, I kept looking at your username and thinking there's no way a rookie is writing this. This man sounds like a veteran technician on a master level! Well and then you said it yourself at the end :) Thank you for all the good information and advice! I have added most of the things you mentioned to the tools list.
I was just watching some more of your videos and found this new one! I want to become a Hvac tech and im glad i found your channel!
Adonis Portillo you can do it .
Hopefully I will succeed 🙏
Keep at it! It’s a great trade to be in!
@Adonis Portillo There is a shortage on HVAC technicians so this is a great time to come on board! I'm glad you are finding my videos useful! Thank you for watching!
Thanks guys! Best wishes for you too
Milwaukee 12 Impact is my favorite and use today. I also bought the RIGID version and it is just as good. RIGID is registered and battery is lifetime warranty. I say this because I used to use DEWALT, and after 14-18VOLT batteries dying over time, I game $1000 worth of tools away to another DEWAULT fan, because I was Done. I bought RIGID, and am happy. I have replaced 2 of my original batteries (FOR FREE)) and have no other problem with them. BUT YOU HAVE TO REGISTER YOUR TOOLS. IF YOU DO NOT REGISTER WARRANTY IS ONLY 3 YEARS. ALSO, CHECK ONLINE AND MAKE SURE YOUR TOOL WAS REGISTERED. I HAVE A FEW BOUGHT ONLINE THE THEY DID NOT REGISTER EVEN THOUGH I FILLEDED OUT RESTISTRATION. IF REGISTER AND APPROVED, LIFETIME WARRANTY ON EVERYTHING FOR THAT TOOL.
Oh Shite!!!! You made a whole video of a list of ultra tech & tools for a HVAC technician. (Comment made before watching the video) I'm so psyched!!!
Haha glad to hear you are excited for it! That list of tools is pretty much the bulk of what every technician works with. There's some expensive stuff in there!
Great list! Thank you for that
Thank you very much, I will watch this video thoroughly again later.
You're welcome! Glad you found the video useful!
I just finished my cert classes and qualified for my union apprenticeship which I test/interview out next month (March) and could be starting this June! So excited, thanks for videos like this. I was told to not buy all my tools at once in the beginning but find out which tools you use the most throughout your training and get those as you go.
No need to worry about the tools you’re going to need if you’re going Union. They provide them.
@@dennisyounker1032 They provide "Some".
Starting out or even in to it, Harbor Freight builds some good stuff. We farm, poultry houses, so lots of switches, motors, capacitors ect. I used Simpson analog years ago, then used fluke, I burned it up and bought a Ames from Harbor Freight and it has worked fantastic. Been dropped hauled in a truck ect and works great.
If you are doing much duct work (new construction, change outs) I firmly recommend Midwest crimpers, reds, greens, hand seemers. However I barely use my handseemers. I would not go with Klein for sheet metal tools speaking from experience. Also Malco Turbo sheers are a must have for ductwork.
If you are in service or going into service you may not use this stuff as much but I wish I was told this when I first bought my tools doing new construction.
Thanks for sharing the list of HVAC tools,you missed the torches,an extra acetylene and oxygen tank and nitrogen tank, the squeegee,dolly,some different sizes of copper fittings and tap cons,you have a very good videos👍✌
Omg jay my favorite part of the video was when u described a must have lighter to light a pilot flame or Something Else😤😇🔥
Huge fan of the clarity in your videos. Components. Operation, troubleshooting, and now useful tools that all techs can use to help there situations. How long you think it took you to be comfortable in diagnosing and troubleshooting all kinds of equipment. I feel like im always seeing something new and learning alot but im now 1 1/2 yrs in and am good with heating but struggle with AC and refrigeration. Lmk your feedback. Thanks keep up the good work
Great Advise Mr Word ... Lol ...I started out yrs ago and didn't have all the great choices out there now ... Great vid Jay ...
Thank you! :) I started out 8 years ago and even I was impressed at how much more great tool options there are now while I was making this video/list.
The E Instrument 1500 combustion analyzer is unbelievable!
In a good way or a bad way? :)
Having Two of everything is good too.
Thanks, great video.
Glad you liked it! Thank you for watching and commenting!
I really enjoy the klein 16 in 1. it comes with the #3 phillips and putting in our CO monitors really comes in handy vs the 11 in 1. just my preference though.
Great info.much appreciate 👏
Hi, Raise Your Coffee Mug !!!! A Big Thankyou For Taking Time AND Effort to putting THIS LIST TOGETHER !!!!!!!!!!!!! AGAIN !!!! Thank You .
Great video. I'm new hvac helper. I likes to watch your video doing about hvac and water heater ^_^. Happy New Year. ^_^
Happy New Year to you as well!! Glad to hear that you enjoy the videos! Thank you for watching and commenting!
I would like to mention a tool. It is a locking adjustable wrench. I find myself using it quite a bit. It works well during times when you need to break up two nuts back to back or when working on a nut in an odd location. Once the wrench is locked on it won't come off like a typical adjustable wrench.
2 more weeks and I hit the field can't wait
Look for deals at your local stores too, I found a nice Husky square bag for $20 and a Milwaukee 11 in 1 for $9
HVAC/R tube cutters are best made by Yellow Jacket. Also, Pipe Expanders is from Rothenberger (Expensive, but great) Tube benders are a needed tool also. Ratcheting is recomended.
Headlamp: I recommend the Klein and/or the Milwaukee rechargeable handlamps.
Klein one seems to last longer and the Milwaukee has the ability to shine brighter.
Don’t buy ones that tank double As because it is more expensive to have overtime. My friend regretted buying a cheap headlamp.
Coast recharging head lamp. Best purchase iv made this past year.
good job Jay. thanks
Thank you! :)
Great video buddy 👍👍
Thank you good sir!
Tool Brands: Fieldpiece, Klein, Milwaukee, Knipex, Hilmor...all I carry on my truck💯
I only agree! All great brands!! :)
Jay HvaC Malco
Your videos are always entertaining and educational and this one is no exception. I personally go DeWalt and Fieldpiece whenever possible for tools. The Job Link gauges with psychrometers and clamps changed the game for me on maintenance calls. I was wondering if you’ve heard of the teaching app called SkillMill by Interplay, I pay $20 a month and have found it to be worth every penny as I’m new to the service side of the industry. If you could do a video on it that would be great
Glad you like the videos! Thank you sharing what your favorite tools are as well. I have never heard of that app so I'll have to check it out. Can't make any promises about making a video on it though :) We'll see.
** Also buy 2 refrigerant wrenches as they get left due to the size of them - they also double to use Blower motor shaft on the squirrel wheels. I would also add offset racketing wrenches (Yellow Jacket sets are great..but they are NOT color coded! lol)
Great recommendations! Thank you! Yellow Jacket offset wrench was added to the list!
You'd be an outstanding teacher.
Thanks. Nice over view . Watch out for those chickens !
Malco bits are a must have
They are great
Amen brother! :)
First, you need a very large wallet to carry around all that cash you get from people who just want their AC working. Charging 380 bucks to put in a $11 capacitor, third day in I knew this was way easier than landscaping.
Thank you.
Hercules I need to remain fair but I hope you win one of the five prizes man! Thank you for always being here!
Very interesting overview
Wera insulated screwdriver set I think they are much better quality than Klein and also cheaper on Amazon. Also the Klein 5/16 1/4 slide lock 10 in one I think is the must have screwdriver. Get it you will never go back to regular 11 in 1 it also has a Schrader valve core remover
On gauges: I do think the 4 port is worth the extra money because you can pull vacuum so much faster on an install. I have yet to learn service so I’m not sure if that 4th hose would make as big of a difference to you guys but it does for me
MALCO makes great sheet metal scissors. About 12-14" long.
Thanks a lot
Really good video.
On duct knife: I rarely use mine just due to the size is inconvenient compared to a cola ding utility knife you can just keep on you at all times.
it took me a few weeks to buy everything, and a few months to open the packaging.
True. I rarely need most tools. I've discovered its easier to have a tool box for storage and a tool bag with the few tools I'll need for most jobs.
Very nice tools bro
I have two bags. My sheet metal bag which is mix match of every brand, and my normal everyday bag which I just recently replaced everything in there with Milwaukee... I also have a bag just for drill bits but you know I'm not counting that
get those uei magnet thermometers, they're just the best.
At my shop you provide your tools but they help you get the expensive ones and if there is a particular one you need they will purchase for you then they will take parts out of each check to pay it off
You’re on the brink Jay!
If you are talking about the subscribers, yes! It's 99.9 at the moment :)
“You’re going to bleed if you have blood in you”. Favorite line of the show!
Haha yeah :) Thank you for watching that far!
I feel like there's a difference in necessities; between service tech and installer. here in the USVI ,a new tech=installer
my favorite tool right now is the driver head that swaps from 1/4 to 5/16
flipity flop
Very long list. Thanks for the video.
Hey bud, I would like to know what u carry on your e everyday bag and also what is the best brand to do your diagnostic on furnace and AC. If you could make s separate video on that. THANKS 😊
On pipe wrenches: the teeth on my Milwaukee wore out very quickly. If you are running lots of gas, especially commercial jobs or plumbing jobs Ridged is the only way to go. I would save up the money for them they are worth it.
Word of Advice TV, you say have more than one gauge for r-22 and r-410a etc. what if you use the fieldpiece SMANV gauge, do you buy two?
One thing I'd add is a 5/16 valve core removal tool for mini splits
I just ordered the U-E-I d-l 479 clamp on h-v-a-c-r meter I here they r good meters as for brand
Really like Veto bags