Respect for all the camerawork man! it is hard enough to manage your tools, parts, workflow.. constantly giving us a super clear look at the work of a master!
Admire your silence. Been a mechanic for 30+ years and not one single day with cursey words and a lot of them. If you were my son, I would brag about you and your ethic big time. Thank you for all your work and videos. Regards from Sweden.
Thanks for the video, a great job, for me very complicated, knowing how to do this with so many different models I see it very difficult, thank you and I hope to continue sharing the videos.
Great video Kev.. the crankshaft sensor in the Bell housing there’s no need to remove it. I done that Kia Ceed during the week I removed the whole cross member but left the steering rack in place I just removed the bolts and used heavy duty tie raps and secured it to the exhaust, both anti roll bar links had to be replaced seized solid had to be cut off with grinder. I couldn’t remove the crankshaft sensor it snapped off in the Bell housing again it was seized in there with corrosion I had a job in getting the little stump out, turned out afterwards there was enough clearance between the flywheel and sensor to have left it in place I had a spare sensor so it was no cost to the customer… just to share my experience
That sensor is right pain. I’ve never managed to pull the box out with it in situ. I always carry spare sensors just for them. But all in all it’s not a bad repair.
Hi kev mate, how are you, kev if I'm filming outside and its windy I always put a piece of material over the microphone to stop the wind howl, only a suggestion my friend, right on with the video, great work kev 👍😉
I have been binge watching your videos and wodered if you had replaced a clutch on a Ford Kuga mk1 four wheel drive. I watched the video of the Ford tdci S max which has the same engine but it is two wheel drive and the procedure will be different. Thanks for the videos man, you're a trooper.
Amazing work kevin! Greetings from Paris 👍🏻, I plan to replace my clutch for the same vehicle model in the video which brand kit could you recommend me plz, I found aisin luk sachs... Thank you great energy🤗
hello kevin.greatest and speeder cluchman😄any différence beetween a3 8v tdi 150 and tdi 184 cluch?iff you come in Marseille on hollydays with your tools and car i let my a3 8v to you fir changing cluch😄😄
Respect for all the camerawork man! it is hard enough to manage your tools, parts, workflow.. constantly giving us a super clear look at the work of a master!
Admire your silence. Been a mechanic for 30+ years and not one single day with cursey words and a lot of them.
If you were my son, I would brag about you and your ethic big time. Thank you for all your work and videos.
Regards from Sweden.
How annoyingly compact that engine bay was, very professional work as always!
Thanks for the video, a great job, for me very complicated, knowing how to do this with so many different models I see it very difficult, thank you and I hope to continue sharing the videos.
Watch them fingers with that hammer kev! You are a true hard worker and my respect goes out to you. Stay safe buddy 👏👍🏻
As always perfect work sir.
Great video Kev.. the crankshaft sensor in the Bell housing there’s no need to remove it.
I done that Kia Ceed during the week I removed the whole cross member but left the steering rack in place I just removed the bolts and used heavy duty tie raps and secured it to the exhaust, both anti roll bar links had to be replaced seized solid had to be cut off with grinder.
I couldn’t remove the crankshaft sensor it snapped off in the Bell housing again it was seized in there with corrosion I had a job in getting the little stump out, turned out afterwards there was enough clearance between the flywheel and sensor to have left it in place I had a spare sensor so it was no cost to the customer… just to share my experience
That sensor is right pain. I’ve never managed to pull the box out with it in situ. I always carry spare sensors just for them.
But all in all it’s not a bad repair.
Gerçekten mükemmel sin dar alanda kısa paslaşmalar 👍🏆Tebrikler çok başarılısın ve gerçekten önemli bilgiler paylaşıyorsun
Hi kev mate, how are you, kev if I'm filming outside and its windy I always put a piece of material over the microphone to stop the wind howl, only a suggestion my friend, right on with the video, great work kev 👍😉
Super comme d’habitude ✨✨✨✨👍🏽
I am very impressed by you 👏 🙌 👌
kevin good performance we are following😉👍
Thank you.
eres el mejor
Need some mobil car lift too .Respect 👍👏
I have been binge watching your videos and wodered if you had replaced a clutch on a Ford Kuga mk1 four wheel drive. I watched the video of the Ford tdci S max which has the same engine but it is two wheel drive and the procedure will be different. Thanks for the videos man, you're a trooper.
Respect 👍
It soon comes around doesnt it Kev the shitty crappy weather. Another good job buddy. Don't you wish you had a nice warm workshop sometimes ☺
It’s here already. I’m just pulling out my winter inventory at the minute.
Thumbs up from me Kevin👍
Have you ever replace a clutch for Dacia logan ? I just wanna know how
How many time have you put your back out lifting the boxes.
Hi kev would you go for sachs complete kit inc dual maas or full kit LUK inc dual mass sachs £265 and LUK £340? Supply only? 🤔 2.0 octavia 5E mk3.
😳😳😳 was that clutch pipe to the slave ? As bad has it looked on camera 😲😲😲 amongst others 😂😂😂
Great video Kev lad 👍👍👍
Yep..😆.,, I kept thinking please lord let this pipe not break or leak after I’d touched it. The amount of rust was unreal.
Hello
Do you know the torque specifications for the flywheel?
Or perhaps have the workshop manual for an I40?
You are a genius.
Now it's raining again, winter is coming. I know that you work in this weather, don't you have a tent overhang?
How many hours does a job like this take you? Do you do much time in the gym, you must be very fit doing this type of work every day
Roughly about 3hrs. No gym mate. Purely hairy chest
Kolay gelsin abi
Amazing work kevin! Greetings from Paris 👍🏻, I plan to replace my clutch for the same vehicle model in the video which brand kit could you recommend me plz, I found aisin luk sachs...
Thank you great energy🤗
Hiya.. AISIN or EXEDY are far more superior quality. The original should be just that ..
@@WMCS many thanks man, you're genius and passionate uk are lucky to have passionate people as you👍🏻
hello kevin.greatest and speeder cluchman😄any différence beetween a3 8v tdi 150 and tdi 184 cluch?iff you come in Marseille on hollydays with your tools and car i let my a3 8v to you fir changing cluch😄😄
I have a question
Suprised you've not changed the dmf at the same time.
lol.. that’s a solid flywheel
That flywheel hasn't been machined.
hyundai avante md
Hey
Only rust 😅