Props are still folded when you start the motors running. Then the front-right propeller is still unfolding when you tried to throttle up thats why it crashes.
No… it’s the problem with propeller fixing… the front propellers has to be 1side A “type and 2nd side B “type Back side 1side B “type and 2nd side A “type…
Tip- before flying, open out your props, to prevent that initial vibration. Also check you have the correct prop on the correct motors! The rear props look correct but the front ones are on the wrong way round....😮 Note 2 props spin clockwise, 2 spin anti clockwise and the props have to be pitched accordingly!
@Experiances Yes they do open out after a few revolutions. BUT it creates a lot of vibration initially in the arm if you don't open them out as the prop is unbalanced. There is a video somewhere on RUclips filmed at high speed that shows just how much the arm flexes while it is spinning up with the props not opened out correctly!
@@pdtech4524 Okay. Maybe possible, However I have never unfolded with my drone and still those works as it should without any vibration. Maybe the initial throttle which feels like starting an engine is to resolve the same.
@@Experiances I tried to post the link, it won't let me for some reason! Search 'Unfold your drone props' it's a video by Droning On. I think you'll be surprised by just how much vibration there is.
The vibration in the start could be a local propeller set used and for 4 bldc motors two clockwise and and two anticlockwise must be used the back side of drone lift but not front you must have swapped the clockwise and anticlockwie Propollers so make sure it is in correct clockwise and anti-clockwise motors
Always check ur props if they are in the correct order and position, these basic checks are just like in real life where a pilot goes through pre flight checks before taking off That’s why u should never purchase a expensive drone if u inexperienced I mean think about those traning ppl take to fly such dji’s those are not just there for show purposes right U should have bought a toy grade drone first which costs fraction of the cost of what this drone costs ( the general functions are same as the dji so U will get a little idea ) and if u crash the cheaper one it won’t even break because they are light weight but these ones are heavy and if they fall that’s pretty much game over Also try to put some prop guards it will save ur props if it falls to some extent Also read the damn manual if it’s ur first time lol Feels sad to watch this even a small drop like this could take of some pieces off ur propellers and it will severely harm ur drones stability in mid air
No… it’s the problem with propeller fixing… the front propellers has to be 1side A “type and 2nd side B “type Back side 1side B “type and 2nd side A “type…
Improper propeller installation, causing the drone to flip over. Also, failing to unfold the propellers, before engaging the motors, will cause stress fracturing, under the Air 2's arms. Research, before you fly, helps GREATLY!
You put propellers at wrong position. Thus, you need to.open wide all propellers' blades to straight position to avoid hinge shaft crack on its main body due to hard vibration from the motors on the initial/startup. If blades arw all wide open, there will be less vibration from the motor onto the main body
All the propellers are marked white. Please make sure the propellers are installed correct. Black to black white to white. You can see the markings on the propeller at the end
First recording on the drone. Camera lense skidding across the ground and props not put on correctly despite the stickers right there that explain. At least non of his bystanders got hit because of his stupidity. Hopefully he got them on PROPerly and got to fly and enjoy one of the best drones ever made by DJI.
@@jedithusnbixby2108 how do you know that's on the incorrect spot save comments same confusing question Don't say this again I'm sorry to say that you shouldn't use this comment ever again
I made a worse crash I was flying and boom I hit metal I was going down quickly and pulled up shortly after I landed and the wings aren’t going fast now
How do you know that the propellers are attached wrong you can't even tell that is wrong I can't even notice what is wrong it's so hard and difficult stop saying this confusing question 🤔 this is the hardest question I ever heard on any comment stop saying this confusing question ever again
Same thing happens, theres a problem in my drone, the props are properly placed, the props are not damaged, and the 2 props dont work so it flip itself, i just look at it and theres no hair or rocks inside the drone, do you guys know the solution?? Am bored at home ehh
Did you at least read how to put on well the propellers?? There are 1000 stickers for making sure anyone does it incorrectly.Also you need to do an exam and pay a secure for your drone otherwise youre flying ilegal.
Todas las helices, son del mismo paso, del mismo lado: se vé, si paras el video cuando están paradas, pues todas tienen la franja de color hacia el mismo lado diagonal😅
I think the prop all same..you must see the prop have a small grey line..make sure to line up correctly at the arm of the aircraft..and then two other prop dont have the gray line..line up it correctly brother..😂
![DJI FPV MAX SPEED 140 km/h vs TRAIN - UNCUT FLIGHT[M-MODE] || DJI ACTION2 FOOTAGE[2.7K] FPV THAILAND](http://i.ytimg.com/vi/fIzfQJhj86Q/mqdefault.jpg)
Props on incorrect
Yes
plus you should always open up your props
Yes
YES
YESSSS
Did you guys even put on the propellers correctly
Make sense
The answer might surprise you 😂
Я так лопасти сломал
Make sense 😄
Fr
Cameraman had one job
LoL
Vo bc ne ulta fan lga rakha h aur cameraman to slow mo capture kr rha h 🤣🤣
😂😂😂😅
Straight disliked 😂😂😂
Props are still folded when you start the motors running. Then the front-right propeller is still unfolding when you tried to throttle up thats why it crashes.
Yas thanks 🤗🤗
No… it’s the problem with propeller fixing… the front propellers has to be 1side A “type and 2nd side B “type
Back side 1side B “type and 2nd side A “type…
@@TurkarJi what thanks? You just wasted 65,000 rupee. Isliye kehta hun ki gawaar logon ke haatho nhi aana chahiye aise mehngi cheej.
@@TurkarJi no point saying thanks if the drone is broken now, 1.5 lakh gone down the drain🤡.
@@Dynamo69420 bhai repair naam kah bhi cheez hai aur paise uske wo jitna udaye ek mehanga hai aur full tut thori na gya hai ho jayega repair
Tip- before flying, open out your props, to prevent that initial vibration.
Also check you have the correct prop on the correct motors!
The rear props look correct but the front ones are on the wrong way round....😮
Note 2 props spin clockwise, 2 spin anti clockwise and the props have to be pitched accordingly!
Those are designed to rotate correctly when they start spinning.
@Experiances Yes they do open out after a few revolutions.
BUT it creates a lot of vibration initially in the arm if you don't open them out as the prop is unbalanced.
There is a video somewhere on RUclips filmed at high speed that shows just how much the arm flexes while it is spinning up with the props not opened out correctly!
@@pdtech4524 Okay. Maybe possible, However I have never unfolded with my drone and still those works as it should without any vibration.
Maybe the initial throttle which feels like starting an engine is to resolve the same.
@@Experiances I tried to post the link, it won't let me for some reason!
Search 'Unfold your drone props' it's a video by Droning On.
I think you'll be surprised by just how much vibration there is.
@@pdtech4524 Sure.
The vibration in the start could be a local propeller set used and for 4 bldc motors two clockwise and and two anticlockwise must be used the back side of drone lift but not front you must have swapped the clockwise and anticlockwie Propollers so make sure it is in correct clockwise and anti-clockwise motors
Yaa. I think he didn't fix the propellers in the right way.
@@rneichgamerz9931 yeah He didn't also follow on how to use it. He didn't unfold the propeller before fly
This is why Tesla will never set up a factory in India.
No one could even buy one lmao, only the rich indians could
How do you know they are Indian just because they are brown they could be Pakistani Punjabi Afghan Iranian Moroccan
@@123goon6 what you just said its basically the same as saying "hey are you japanese" to a obvious japan man, in japan.. why japan? Idk
@@123goon6 they are most likely indian
@@h3li064true but it might be disrespectful for some people
Always check ur props if they are in the correct order and position, these basic checks are just like in real life where a pilot goes through pre flight checks before taking off
That’s why u should never purchase a expensive drone if u inexperienced I mean think about those traning ppl take to fly such dji’s those are not just there for show purposes right
U should have bought a toy grade drone first which costs fraction of the cost of what this drone costs ( the general functions are same as the dji so U will get a little idea ) and if u crash the cheaper one it won’t even break because they are light weight but these ones are heavy and if they fall that’s pretty much game over
Also try to put some prop guards it will save ur props if it falls to some extent
Also read the damn manual if it’s ur first time lol
Feels sad to watch this even a small drop like this could take of some pieces off ur propellers and it will severely harm ur drones stability in mid air
Dji clearly says in the manual that you must *unfold* all props before taking off😅
Common sense says in the manual to unfold them
The props are incorrect, I have my own mavic air 2 it doesn’t need to open props he will do it by itself
@@mishgan_11
Which mavic 2,mini or air?
@@asniperaimatyourhead air
@@mishgan_11 it's weird bcuz i have mavic 2 air too but i have to unfold the props every time before takeoff
No… it’s the problem with propeller fixing… the front propellers has to be 1side A “type and 2nd side B “type
Back side 1side B “type and 2nd side A “type…
Improper propeller installation, causing the drone to flip over. Also, failing to unfold the propellers, before engaging the motors, will cause stress fracturing, under the Air 2's arms. Research, before you fly, helps GREATLY!
Great skill and also great camera works.
🤣🤣🤣🤣 exactly top notch
All round perfection
😀😂😆
You put propellers at wrong position. Thus, you need to.open wide all propellers' blades to straight position to avoid hinge shaft crack on its main body due to hard vibration from the motors on the initial/startup. If blades arw all wide open, there will be less vibration from the motor onto the main body
The way he was putting on spects🤣🤣
bro didnt even pull the stick back down, he just kept on damaging it until it had enough
I see like four mistakes in the first 2 seconds of this video.
Great camera work
😂😂
I think so
All the propellers are marked white. Please make sure the propellers are installed correct. Black to black white to white. You can see the markings on the propeller at the end
You cannot see it right now dude why there so many comments say this stop this game of arguments
@@Mingzhe583because their right 😂
What do you put the props on the wrong motors
Yeah it happened to me also
Bro has no idea what he is doing🔥
I do not unfold my drones propellers no more. But I never lift off as soon as the motors start. I let them spin a while and then lift off.
First recording on the drone. Camera lense skidding across the ground and props not put on correctly despite the stickers right there that explain. At least non of his bystanders got hit because of his stupidity.
Hopefully he got them on PROPerly and got to fly and enjoy one of the best drones ever made by DJI.
Maybe doing mistake while plug n play the propellers.. Please check A & B propellers plugin must in right position ..
Mavic fail
It’s not the original propellers & mismatched!!
why didn't youopen the props before launching?
Also u should learn the motor start and stop command :) just move both sticks to the inside corner and it should stop the motors
As an fpv pilot i feel like guys flying mavics and crashing are dumb like really dumb
The number one rule of flying a mavic is unfolding the props first before take off
No the propellers were on incorrectly. The props can be folded but it will unfold itself
@@jedithusnbixby2108 how do you know that's on the incorrect spot save comments same confusing question Don't say this again I'm sorry to say that you shouldn't use this comment ever again
You should try to your own drone, fly with folded props then see. His comment makes sense though@@Mingzhe583
Maybe it was because the propellers were folded or maybe if you had fix the propellers in the past you’ve might have not put them on correctly
Ох уж эти индусы, Жади воздушные винты не могут правильно одеть
Drone buyers must complete IQ test before buying🤗
😂
1 the props can be closed since centrifugal force will open them
2 he fucked up the props stetting
3 its not broken its just gonna stratch it
When you take off with the propellers still closed it puts huge stress on the motor
He must have put the props on the wrong way
the wings are wrongly installed
Sometimes
People are not smart and run through things
Trying to get them done as fast as they can which makes a mistake when that
Happens
I made a worse crash I was flying and boom I hit metal I was going down quickly and pulled up shortly after I landed and the wings aren’t going fast now
Happened to me too i Think ur one motor is broken
Brah
They say DJI drones are so easy to fly even a monkey could do it... I guess they're wrong.
There are markings on the drone which propellers goes where you attached the propellers wrong
I guessed it too.. it happened with me! Followed the markings and then sorted!
How do you know that the propellers are attached wrong you can't even tell that is wrong I can't even notice what is wrong it's so hard and difficult stop saying this confusing question 🤔 this is the hardest question I ever heard on any comment stop saying this confusing question ever again
@@Mingzhe583vruh
Maybe the screws are rust and the props can't spin properly
Same thing happens, theres a problem in my drone, the props are properly placed, the props are not damaged, and the 2 props dont work so it flip itself, i just look at it and theres no hair or rocks inside the drone, do you guys know the solution?? Am bored at home ehh
Bro turned the propeller into VTOL💀
Their drones, not a plane.. ofc its vtol
You should get a landing pad to keep those propellers clean during the take off brother.
No the hand take off and the hand landing are much better . I don't need a landing pad which takes a lot of space.
@@stefan.w979 of course that's advice for people who use the ground to take off
First open drone propellers 🤣🤣
🤣🤣🤣🤣
You can fly with the propellers still folded the right ones need to be on
@@dandimitrievski5926 as he just demonstrated. 👌
Kabhi uadaya h ?
@@pahadimusafir822 bro m drone operator for movie's... Cm i vl teach u... 🤣 free may
No surprise by seeing sitting maneuvering
Propeller installation should be changed..
Bhai mere phahle hi wo properly thrust nahi bana pa raha hai kya khak udega
Always shake your drone to free your prop before starting
Wtf?
This is why you should buy cheap drones when learning to fly.
Bro intha drone name enna bro and model enna bro
👍
Nice job guys, you didn’t take the tape off the propellers and it stuck.
How can you call this a "crash" when the drone didn't even takeoff
Is it ok?
Next he should avoid to operate a drone using midd finger
Bro the drone want to make a FPV launching 💀
Cost tell me
Am guessing he installed the propellers wrong. Propellers with Grey rings need to go on the grey marked rotors and black to black.
Cmon dont make fun of the pilot guys 😔
Props are not installed properly
bro forgot to watch a tutorial before SWITCHING YOUR PROPELLERS
Wrong props, check the markings on the props.
Oops propellers are not installed to spin the correct direction. You’re lucky no one lost a toe.
Who did they scam to get that??
Put wrong side propeller.Why?
Hold both sticks in the same way you start to emergency stop the rotors
Bro use wing protector and if you don't have buy 👍
Сделайте калибровку
Dude it's because you didn't follow on how to use the mavic 2. That's why it happens
Ooof the drone pilot is way more interesting than the drone
Front props are switched backwards
Oh man , sorry guys , i feel for you! Its so difficult flying a drone , good luck! Grtz from the Nederlands
If you have an iq of 0.1 and can't read a manual it is indeed
Buys a drone, does the exact OPPOSITE of what the manual says…. Wonders why it don’t work.
someone didnt read the manual lol props ma friend props
Thats why you should NOT buy drone from temu
And this is why I unfold my drone’s props. It’s to prevent it from crashing and giving burden to the motor. (to unfold ofc)
Yeah that's what we do on DJI drones
Did you at least read how to put on well the propellers?? There are 1000 stickers for making sure anyone does it incorrectly.Also you need to do an exam and pay a secure for your drone otherwise youre flying ilegal.
This happens because you didn't install the propeller in the right direction
Low battery?
No he didn’t even open the props
How did this guy manage to get a license
You dont need a license for For a drone that weighs less than 250g
why is it not flying?
Today I have ordered in 1699/- only, will unbox soon on my channel
Todas las helices, son del mismo paso, del mismo lado: se vé, si paras el video cuando están paradas, pues todas tienen la franja de color hacia el mismo lado diagonal😅
Still below, I was told to move forward, it really is a drone with wheels😅
Como conseguiu encaixar as hélices o contrário? 😆
Bro has been the reaction time of a fossil 💀 props on incorrect, why didn’t u throttle down IMMEDIATELY!?!?
Dji clearly has a disclaimer that no chapri is allowed in 100m radius, if Chapri comes near drone will behave abnormally
Props are placed in wrong way..plz first learn how to place props then try to fly it😂😂😂
How do you know
You can see how the drone reacts@@Mingzhe583
@@Mingzhe583your cringe af trying to support this guy, its obvious.
Bro you fix it's propellers wrong that's why 😅
Propeller might be in wrong motors they have markings on them !!
Bhai ye kitne pase ki aati hai
I love watching people not read directions and know how to use what they just spent hundreds of dollars on
Apparently this is not the original model but another cheap imitation
Propellers are not placed as per CW ANS ACW
The right top propellor wasn’t put properky
Dude thats the easiest drone to fly..and you cant even get it to hover..?
Beginner put into Normal mode and make your remote control is calibration setting is done properly.
You put the propellers on improperly...😅
Props opposite dale hai bhai change it
I think the prop all same..you must see the prop have a small grey line..make sure to line up correctly at the arm of the aircraft..and then two other prop dont have the gray line..line up it correctly brother..😂