what input are you going into? i can't really tell.. i get your going out from the main output with a 1/4 , but what input are you going into in the power speaker? thanks !
If you connect it to do both mains and monitors, are both pairs in stereo? Or is it a weird mono setup? Or, are like the mains the left channel and the monitors the right? I'm trying to find one of these that will run the 2 pairs at all times.
You are correct... To overcome this is, use the 7 band graphic eq on the yamaha to send only the low frequencies to the sub and then send the mids and highs to the main speakers. You are essentially doing your own crossover. Check your speakers to see what frequency to cross it over at. I use 100 hz, I think it is 95 hz on the graphic eq. If you are only using one side of your amp to do this application, your powered speakers may allow you to set set the crossover point of your speakers. My yamahas allow me to do that. In that case, send the full range signal from your yamaha mixer to the sub and to the mains. I hope this helps.
Fui musico profissional , tive uma EMX212 , vendi , Tenho uma EMX512sc , nunca consegui usar , o som é uma bosta ( informação falsa , ela não tem 500 watts rms por canal , se tiver 500 wrms no total é muito ) . A yamaha tem coisas boas , mas esses modelos ficam a desejar .
![[DRAGON BALL LEGENDS REVEALS ＆ STUFF] LEGENDS FESTIVAL 2024 Special Edition Part 1](http://i.ytimg.com/vi/mV5bGIswTtQ/mqdefault.jpg)
Down to earth straight forward tutorial. Excellent!! Thanks!
Thank you so much this really helped me out.
Very helpful. Thanks👍
Very helpful thank you
what input are you going into? i can't really tell.. i get your going out from the main output with a 1/4 , but what input are you going into in the power speaker? thanks !
Do i need Power Speaker for moniter
but how do you power two main speakers from just that one output ?
You daisy chain your mains. So you connect one main to the other main, then connect to the pa amplifier. Same for the monitors.
@@nitrofiche7206 Thanks !
If you use the powered outputs for main and monitors , can use still use the unpowered out for sub or does that cancel it out?
Nope doesn't cancel out
Sorry for the late reply. I don't think it cancels the other outputs.
What kind of speaker u used? Series?
how do I chain two emx powered mixers so one will run main and the other runs the monitors
Can I cocnect another amplier and 1 mixer to that type of power amp?
Do these have USB input for input into and out of a computer?
If you connect it to do both mains and monitors, are both pairs in stereo? Or is it a weird mono setup? Or, are like the mains the left channel and the monitors the right? I'm trying to find one of these that will run the 2 pairs at all times.
Are these amps have the option for 240v to 110v switch?
Can i use headphones on this mixer ?
Hi. About your sub idea. There is no crossover to split signal, correct? So mains and sub are receiving high, mids, and lows?
You are correct... To overcome this is, use the 7 band graphic eq on the yamaha to send only the low frequencies to the sub and then send the mids and highs to the main speakers. You are essentially doing your own crossover. Check your speakers to see what frequency to cross it over at. I use 100 hz, I think it is 95 hz on the graphic eq. If you are only using one side of your amp to do this application, your powered speakers may allow you to set set the crossover point of your speakers. My yamahas allow me to do that. In that case, send the full range signal from your yamaha mixer to the sub and to the mains. I hope this helps.
Correct
2:38 thins time!!🎉
could I use the EMX5 12 to send the mix out to a laptop for recording or streaming? Like a USB connection, or is there another way?
Yes you can with 5:01 REC OUT cables Red and white
How do i connect emx512sc to total pa bluetooth speakers?
you rock man
Were is the PAN or balance
I didn't know where to connect my powered stage monitors
There should be a monitor out on the front panel. It will be a 1/4 inch jack.
Excellent 👍
Thank you!
para que son los botones amarillos que dicen COMP
son compresion para los microfonos, regula los sonidos pico de ellos
para que sirve el botón que dice parameter
I literally got the amp on full blast and this shit wispers at me just as loud as if i got my phone on 1% volume
Quanto vale o Mixer 512 Yamaha
your video not clear , need brighter light
Too dark don’t see
Fui musico profissional , tive uma EMX212 , vendi , Tenho uma EMX512sc , nunca consegui usar , o som é uma bosta ( informação falsa , ela não tem 500 watts rms por canal , se tiver 500 wrms no total é muito ) . A yamaha tem coisas boas , mas esses modelos ficam a desejar .
Horrible tutorial