Test Leads?? Scope and Meter Leads? Make You Own Instead! Custom Length and types!!
HTML-код
- Опубликовано: 20 окт 2024
- I will show you how I make my own test leads for the fluke. This can also be done for the end of test lights and making your own custom tools. It is a far better result being made to your specific application. You can control length and type of leads for any application so you can test as you need. Never buy test leads again! Buy these products through our Amazon affiliate link here: www.amazon.com...
Uses a torch instead of an Iron to solder, probably the same one that he used to light the smoke he had while doing shop work and sharing it with the world before a manowar ringtone goes off. Unreal, great vid.
I was glad to see you use the flux.. I would recommend that to everyone. Don't skip the flux.. The flux in the solder is not always going to be enough if the surface isn't tinned.
So true, a lot of people don't realize that flux cleans and helps pull the solder into the work.
The flux in the flux core solder burns away in a hurry.
Flux + Capacior + 1.21 Jigawatts+ 88MPH = Going back to days before CAN.
Back in the day when Radio Shack was still around, I made my own sets of jumper wires for electrical testing. Bought some speaker wire and alligator clamps, still use them today.
Hahah fixed my primary coil wires with speaker wire to get home! Off side of freeway...used it for 3 weeks before replacing! Never underestimate the speaker wire
I actually made complete sets of these about 6 ft 10 ft 14 ft long each using 14 gauge silicon wire as Joe is doing all in matching colors and ends for my SnapOn Verus oscilloscope so I could keep the Verus in my roll around or on a bench. They were a quarter the cost of bought and work great. Also a good quality flux is important.
Thank you very much, Joe! Thanks for all your content and time you have into this channel. I and others really appreciate it.
smokin a ciggy while doin work in the shop, just to let u kno who runs things
I didn't even realize you could make your own leads!!! Great informational video!!! Thank you!!!
You bet!
Thanks for taking the time to show us this handy money saving tip going to order my supplies today!
That's good stuff Joe. Just about everything is available on line and those kits are going to be very handy for a lot of people.
Joe, great video! Just a few thoughts:
First-off, it is really great that you show tech's how to do this because they will never be out of luck!
Second, I am actually Mil_Std certified for soldering with emphasis on missile systems. That being said, when you were NOT totally filling the solder-cup area, you were actually doing it correctly! This is called 'contour-soldering' and is the correct way to do it for several reasons. First, you actually have a solder-connection that is 'inspectable' whereas if you fill it, you have no idea if you really have a 'cold' connection inside a solder-blob! You should be able to see the individual strands always; some will say that solder-blobs are stronger but if that is you aim, you really have issues! Next, if you've applied enough solder to have a solder-blob, then you have also 'wicked' solder up further inside the insulation and created a sharp-delineation that can cause individual strands to break instead of bending; it seem counter-intuitive but has testing behind it. Finally, many solder blobs are actually 'cold-joints' because a large mass of solder was quickly applied and leaves a bulbous structure not 'wetted' to the rest of the connection structure; you should be able to see the molten-part of the solder mass suddenly sink, thus showing wetting.
So Joe, you were doing it right all along...
Thank you for your service, and for your very good explanation. I've made a lot of solder repairs over the years, and have had no failures of these joints. I guess I can do something right. 😂
I love making my own, banana including leads test lights, making home made lights etc great video Joe this should help some people out for sure.
Yeah like I had commented a while back "like that of John Fluke MFG" and YES if you go somewhere like Greenbrook Electronic's in North Plainfield, NJ you may get some amazing things but like you said they're expensive as hell. You're creating your own tools and you're saving a lot by doing it ... Now you are starting to think and work like that of STADT specialist-the German word for city or in Hebrew (שטאדט) which spells out the acronym Special Tools And Definitive Techniques. If you don't see that as a compliment that's too bad because the world as we know it is in desperate need of people like that :)
Thank you very much. My father taught me from a young age that if you are capable of making anything, it will be better than anything you can buy. He was a blacksmith and welder.
Greenbrook Electronics is like going back in time. It reminds me of 80's Five and Dime.
@@JoesAutoElectricThanks for sharing Joe!!!! Super helpful video- solid basic fundamentals never get old and never too old to learn!!! Thanks again for sharing- I hope all is well with you Joe…
Nice demo, I clicked through a few of the choices on your Amazon link. Didn't know about the angle adapters or the excellent silicone wires. Presently Fluke are selling crappy leads with their lower level meters, they are cutting corners for the lowest price point meters. I've made a few test leads through the years but it is reassuring to see a pro do it, very similar to how I did it. I like those piggyback adapters to tie in a scope as well.
Thank you man. They always work well as long as you take care to solder them properly. Other than that, they are perfectly easy to do.
Thanks for putting this tutorial together!
Down to earth & down to business, right on partner.
Thank you.
You gotta appreciate a man that can multi task. That's cigarette aint gonna smoke itself
You're clever. Focusing on the cigarette with all the other stuff going on. Good job.
Joe I got a tip for ya... Use DL Handcleaner (blue package no pumice) and a piece of foam rubber and gently clean your case for the meter and the meter surface (do not get it in the teminals) it will clean it up like magic. works on all surfaces like rubber leather great for steering wheels.
Thanks Lon!!!!
Wd40 on a clean cloth looks brands new after. Use on all my tools
Where can we buy the leads? Great video, thanks for sharing.
Thanks Joe. I’ll be going to your link and help support you for all the sharing and help you have give me Artie ❤️
Hi, Yes ive been using those connectors for a while now making leads for my test lights and adaptors for my meter.. I do find sometimes that when soldering the straight connectors the surface can be a bit shiny and the solder dosent stick.. This is where the torch may be better than a soldering iron as you can get more heat into the pin...
I actually prefer the blazer micro torch for this because of that. However, for those who might not be used to a micro torch, I recommend the solder gun. Safety and less chance of mucking it up.
Sweet! Thanks for the tip. I'm going to make a short lead for an alligator clip for my power probe now!
Good job on the leads Joe, now go help that guy start that truck.
:D awesome intro! Ive been considering making my own for a while since a good new set goes around $30 by them self,
I loved the intro bro! Thank you as always!
Thanks for the tip...
Thank you very much. All I have to do now is find where these wires and components are sold.
I my self not a mechanic like you, I am a builder.But we do similar things just like you. We use what we can and have in a given situation on the spot to atchieve task without compromising quality.
I have had mixed quality when buying Chinese prebuilt leads so I have started repairing and make many of my own as well Joe. If the quality is bad at that point it’s my own fault.
That is my exact thoughts!
Good information keep going bro
Nice assortment on that Amazon link, I'll defenetly look there first, I like those self soldering heat shrinks.
Nicely done. When I make up leads, I attach an alligator clip. I have not seen those neat adaptive ends before.
I need to make a jumper wire to test my whirlpool ice maker. It is shown using a paper clip and wrapping it with electrical wire? Thanks! I subscribed.
Good video... I just made 5 different amp leads To plug in fuse box for my budget oscilloscope saved big bucks doing it I love it when I can make my own.
Very Nice video Joe, just would be cool if you gave the exact names of coupling leads and where to buy online. Thanks again
The plug you used has a flat side and a round side (near the soldering area). I've never been able to figure out if that has a purpose as to which side to thread the bare cable.
I have some leads I made from a coil pack harness. They hook up to most of the harnesses I run into.
Nice work. 👍
I might agree here if you have all of the parts to do so for low cost or free. Otherwise the time investment and low cost for stuff needed otherwise it’s cheaper in the end to buy them at a reasonable price of course. Custom ends are sometimes needed and then it may be better to build your own. In the end you need to decide how valuable you time is and the cost difference from making and buying sometimes it’s better to buy than make.
Nowadays you'll probably get China made JUNK. for best QUALITY, and affordability, order the parts before you need them!
Best part, " NO ONE IN THE SHOP CAN CLAIM THEM " DAMN STRAIGHT Arise, FREAKIN THIEVES.
Looked for a parts list but only saw a playlist when I went to video description. Did you put a list of parts / links and also am I clicking something incorrectly when trying to click description and only seeing a playlist??
***Edit*** Dih saw the link now. Had to scroll up…. 😅😅
Hi Joe. Good morning. My name is Winston all the way from St Vincent & The Grenadine a hundred west of Barbados in the Caribbean. Any how I did look at two of your tube videos. Making your own test leads & Rant ( Sometimes We Have to Vent). I am an auto technician my self understand the feeling. Any however I would link to try Making my own test leads. Could you recommend link where can I purchase the Red, Blue, Yellow and Black test leads or Wires. Also the Ends fitting.
Regards.
Winston.
Yes sir, thank you.
If you go to my Amazon affiliate link you can buy them through there.
Good job, Sir!
Hey Joe thanks for great content
Custom built 👍
I've seen positive lead with a add inline 10 amp fuse.
Just wanted see if you seen this done or heard of this?
Yes sir, can be done as well.
Guess what I am going to order.... As I am fed up of getting crappy leads. And yes I did find helpful.
Nice! Let us know how you like it.
Hello sir .
Great video .
Question does it matter how long tje test lead could be meaning does interfere the link with the measure?
Wheater 3 feet or 12 ?
I want mine to be longer than normal for better access.
We appreciate what you do sir.
Hey buddy can you pls lmk about my question.
Does it matter the link of the test lead for accuracy?
Very thorough. 👍
Sweet a fellow iMovie user! I nice job on the leads. I've been thinking about making some really long ones. A local electronics store sell the silicone super flexible test lead wire by the foot in about 7 colors.
Where do you get the ends and what gauge wire do you use?
I need to make some.. 👍👍
What is the safest wire gauge to use?
Looking to make my own leads what gauge wire should I use
nice intro, that was cool
Great video! It comes just in time when 2 sets of leads went bad on me. How long do they typically last you? Thanks for the video! 👍
Just as long as you can expect from any high quality leads. As long as user error is not involved.
@@JoesAutoElectric
User error, just had to involve me didn't you? LOL
lolol
He finally gets to the point at 3:15.
Aww, was I not fast enough for you? Aww .. snowflakes need not be here.
Where do you buy components like those and what gauge wire is that? I like the large grounding clip.
Said in the video I chose 14 gauge wire for this set. All of this is available in my Amazon store. Go through the link in description.
@@JoesAutoElectric I went to your amazon store link, it seems like it out of date and mostly empty
Wow that's nice
What gauge wire??
Are you the same Joe in the most recent video wit Ats with the pony tail guy g trulia ?
You look younger on the most recent videos if that is the case .
@@jordysandino6577 I don't know what you're referring to honestly.
G has used and shown some of my tools in his classes, if that's what you mean.
Terrific.
yea the fluke leads are costly but you can custom make stuff
Thx Joe!!😊 Do you have a public email, please?
Tool hoarders for the win.
One of the last set I bought(From China) had no continuity! And ONE FREAKIN STRAND OF HAIR THIN WIRE!
😳
Sweet link to Amazon. Got a few things already, but found what I wanted to ask about!!! Thanks!
This guy is freakin awesome!
Arise Chikun one is better than none
Wuhan special
Yeah just use the good ole fashioned 100W leaded stain glass soldering iron. LOL
Did I hear few seconds of ManOwar
You and me...we can be friends.
I heard that as well . Long time listener of them . I personally like Gloves of metal . When I lived in MPLS MN years ago and the local Hell's Angels had a shop on lyndale Ave called MPLS Custom Cycle and they had a huge poster of the whole band up on the wall behind the counter and display case with the band members all sitting on custom bikes they built for the band signed by each band member for many years until they got shut down after Pat Matters home got raided and he went to prison .
🙂
🙂
is covid 19 affecting your business Joe?
More than hurting Lon...
@@JoesAutoElectric I hope it gets better I am unemployed too.
I know brother. Things are looking all bad here. NY is on lockdown...NJ will be next. I'll still be here looking for something to come through the door.
Parts wont be available anymore. Your channel is going Mexican lvl soon. Put a ford motor into a Chevy because you wont be able to buy parts soon.
Devin Slurry lol. Fords are way harder to get parts for. Soon I’m going to have a donate TP button. Who needs parts when you have toilet paper. 🤣
WTF is sodder?
Aww look, another internet clown. You should be proud buddy
You're the reason a lot of guys don't share knowledge online. Now, go crawl back under the rock you came from. Think it over a bit, then come back and apologize for your sheer stupidity. It's ok though...it's the same as when someone is dead...you don't know any better.
Dude put the cigarette down
Dude mind your damn business. Always one.
Let smokers smoke geez
That's good stuff Joe. Just about everything is available on line and those kits are going to be very handy for a lot of people.