THANKS BRO, NICE EXPLANATION,, Ganyan din yung ct ko dapat pointing to meralco yung arrow..kc pag baligtad sa display panel nang inverter ko may minus sign,sa meralco consumption,tapos di nabagal ikot nang electric meter..
If it works in your set up then its good for you. Just make sure your CT polarity was connected at correct terminals. We can do also flick test of the CT to determine its correct + or - cable. Sometime manufacturer makes mistake also. I did flick test on my CT before installation.
Red is for positive, Black is negative. In the video, i extended the short wire from the CT. That is why the black becomes blue when connected to the inverter.
Yung material nya pang indoor lang. Mas maganda sa loob ng panel. Madali masira ang insulation nya pag direct sunlight at ulan. Baka magawaan pa ng paraan maitago sa may bubong.
@jfrelectechnical6652 salamat sa pag reply boss. Masyado kasi malayo yung inverter ko doon sa panel namin. Pwde kaya lagyan nlng ng cover yung ct sensor ikabit sa outdoor?
Hello dear friend , i need your help please, i have 2 inverters and the each inverter have a ct limiter, i will connect 2 ct limiters on the same wire? as you show on our video? thank you very much
Yes you can install two GTI solar in your electrical system. Two CT limiters in the same wire of the main power supply. Sorry for the very very late response.
Shouldn't the CT clamp go on the live feed cable coming in to the RCD and arrow putting out of the house so the CT clamp shows how much is going back to the grid. I am talking about Sofar hybrid inverter.Thank you.
Yes, thats what I did in the video. Same with grid tie and hybrid sofar inverter. CT limiter was clamped in one leg of the main cable and arrow pointing out of the house.
Sir, note that my solar inverter grip on rather the energy was more expensive One question, where exactly does the sensor go? ct I have 220 where I connect it in the positive or negative phase or ground in which?
@@jfrelectechnical6652 sa time 7:53 nag export ka pa din ng power sa DU. ganyan din kase setup ko, palaging nageexport mag high ang harvest versus sa house load
sir may babaguhin paba sa setting ng inverter once na nakabit nanatin yung ct sensor? or naka default na yung sofar inverter natin para talaga sa naka activate ang ct sensor?
THANKS BRO, NICE EXPLANATION,, Ganyan din yung ct ko dapat pointing to meralco yung arrow..kc pag baligtad sa display panel nang inverter ko may minus sign,sa meralco consumption,tapos di nabagal ikot nang electric meter..
baliktad dapat and ct towards sa load kasi nung sinubukan ko yung away nag negative ang reading
If it works in your set up then its good for you. Just make sure your CT polarity was connected at correct terminals. We can do also flick test of the CT to determine its correct + or - cable. Sometime manufacturer makes mistake also. I did flick test on my CT before installation.
Da best....
Please confirm the wire colour of CT, Red-Black polarity
Red is for positive, Black is negative. In the video, i extended the short wire from the CT. That is why the black becomes blue when connected to the inverter.
Sir pwde po ba i install ang ct sensor sa outdoor? Sa main wire sa labas ikakabit before papasok ng main breaker. Pwde po ba sya mainitan at maulanan?
Yung material nya pang indoor lang. Mas maganda sa loob ng panel. Madali masira ang insulation nya pag direct sunlight at ulan. Baka magawaan pa ng paraan maitago sa may bubong.
@jfrelectechnical6652 salamat sa pag reply boss. Masyado kasi malayo yung inverter ko doon sa panel namin. Pwde kaya lagyan nlng ng cover yung ct sensor ikabit sa outdoor?
Hello dear friend , i need your help please, i have 2 inverters and the each inverter have a ct limiter, i will connect 2 ct limiters on the same wire? as you show on our video? thank you very much
Yes you can install two GTI solar in your electrical system. Two CT limiters in the same wire of the main power supply. Sorry for the very very late response.
lahat po ba ng inverter pati hybrid may ports para sa GTI PV Solar System/CT Limiter?
Meron po basta grid tie inverter...
Shouldn't the CT clamp go on the live feed cable coming in to the RCD and arrow putting out of the house so the CT clamp shows how much is going back to the grid. I am talking about Sofar hybrid inverter.Thank you.
Yes, thats what I did in the video. Same with grid tie and hybrid sofar inverter. CT limiter was clamped in one leg of the main cable and arrow pointing out of the house.
Sir, note that my solar inverter grip on rather the energy was more expensive
One question, where exactly does the sensor go?
ct I have 220 where I connect it in the positive or negative phase or ground in which?
Kahit saan sa dalawa...
Bro nakadisable reflux derating mo dito?
Pag mataas ang harvest and lower and load, yungnsbrang harvest babayaran mo sa du.
Tama ba?
Hindi brod Grid Tie lang yan di Hybrid. Kung anong load yon lang ang tatapatan ng inverter. Di siya magbibigay ng sobra sa DU.
Wala ako net metering kaya di dapat sobra sa load kundi. Dahdag singil pa sa atin yon ng DU.
@@jfrelectechnical6652 sa time 7:53 nag export ka pa din ng power sa DU. ganyan din kase setup ko, palaging nageexport mag high ang harvest versus sa house load
sir may babaguhin paba sa setting ng inverter once na nakabit nanatin yung ct sensor? or naka default na yung sofar inverter natin para talaga sa naka activate ang ct sensor?
Sakin kasi may binago ako sa setting para gumana ang limiter.
Ask lang po mga idol . Ung arrow ung ct limiter pointed papunta sa main breaker or pointed papasok ng bahay??? Pls help
Anu tama install ng ct limiter arrow pointed to meralco(main breaker) or papunta sa breaker sa bahay???? Thanks
Going to meralco.
boss sofar GTI.. pwedi ba yung 2000/1 ratio
di ko matandaan kung may setting selection para sa ratio ng CT. Ito kasi binigay ng vendor para sa model ng sofar GTI ko.
Which inverter is that?
Sofar 2.2 KW Grid tie only.
Can You please name what CT specification is for this Sofar inverter model?
Ratio CT is 1000:1. That is the specification required for this GTI Sofar model
Sir, panu kung line to line ang system ng DU? Panu ikabit ang CT?
2 ct i think. so you need an inverter with two ct limiter otherwise two inverter. i guess
kahit sa line 1 or line 2 as long follow correct orientation of arrow that point to DU... tHANKS
Idol pa help lang. ung arrow ng ct limiter pointed to main breaker(to meralc0) or pointednpapunta sa breaker ng bahay?
yung sa akin lumalabas "Reflux Degrading" nung kinabit ko yung limiter
Kung wala kang net metering kailangan. Naka enable ang reflux derating boss. Kung meron net metering i set naman sa disable.
Bro me alam ka panu parallel dalawang inverter na sofar?
May kanya kanya ba sila pv panel.?
Di ba mali ang gamit jan ct limiter? Kasi may export pa rin eh
Oo bro kanya kanya Sila Ng Panel balak ko Kasi parallel dalawang SOFAR inverter GRID TIE LANG 2.2kw
@@jfrelectechnical6652oo
Paano po kung hindi naka MeCo meter?
Kung walang Meco o kahit anong Distribution Utility, hindi po angkop ang grid tie na inverter. Stand alone na solar set up po kailngan.
Mali pala install ko ng CT SLAMAT..