There should be about 4 screws that holds the transmission to the frame, once you take off those 4 screws the transmission should slide out of the frame of the truck.
Hi nitrorcx. I bought the forza and have been having a problem with the transmission. I used one of your videos to take it out and check it. Nothing was worn out and everything was in good condition. The only problem is it wasn't shifting onto second gear. I used this video to adjust the tension and now the car wheels lock when I'm in mid driving. Did I adjust the wrong nut? My gear mesh is set perfectly but I also tightened the brakes but like I said it was running fine so I'm guessing it isn't
Great vid! Just got a Tornado S30 a week ago, my 3rd nitro. I was wondering if you can explain how a burned up 2nd gear and 1st is still mint? I'm thinking engine/clutch bell placement, but i've hardly hit 2nd, it had a hard time changing gears. Any advice would be greatly appreciated.
So this mean's that my car in in second gear because both spin.but they both spin at the same time even if the engine is not even running can you help and tell me whats wrong. GREAT VIDEO
Hello. may I ask for help please. I have a two speed clutch which grabs a pin on the gear, to shift to second gear. However I am not sure which way round to install the clutch. You would think common sense says the lever should fly out with the leading edge in the direction of rotation, but surely if the second gear is already spinning faster (as it is connected to a larger pinion gear) , it will simply push the lever back in, as it will brush the back edge of the lever. so my question is - Should the clutch be installed with the leading edge of the lever (the bit that comes out) facing into the direction of rotation, or away from the direction of rotation. - Thank you
What about if it doesn't want to move at all and just revs up? All the screws are in place as far as I can tell. There's no damage to anything that I can see. I have a forza, Brand new. Ran 2 tanks and it just started revving and only catches every once in a while under very low throttle.while the weight of the car is on it. But if I pick it up, It works fine.
Hey my second gear chiped and i cant get the screws on the right side between the exhuast and the metal how do u get the exhuast out of the way or would u please make a vid of taking it all apart down to the gears please
i had a car for over 10 years that would never shift, when it was new couldnt even rotate the spur gear to adjust it, it was locked from moving....well it turns out the adjustment screw backed itself out and jammed second gear on all the time, i had to take it all apart and put it back together now its fine, but i never seen anyone mention this so if you cant even adjust it make sure your grub screw isnt out from vibration
waaitttt how can the small pinion gear be idle if it sets on the clutch bell. i mean when you put the transmission the large pinion gear sets on the small gear on the clutch bell and the small pinion gear on the transmission sets on the large of the clutch bell. so how can it be idle??
The manuel says its the two way drive clutch that im talking about. Im missing that middle grub screw, will that not make my forza drive? I dont even know if it had one i just bought it from nitrorcx a lil over a month ago...but all it does is rev and the gears are meshed perfectly, plz help.
my car wont move a 2speed 4wd nitro sonic.. engine on or off the car is stuco i have loosened brake..same problem.. this happened due to changing my 1st gear plesae help
Can any one help me I have a Ofna dm1 spac and this isn't the Frist time this happen the 2 gear stripped out. I thing the Gap was too much but not 100 sure. But how do I gap them right and prevent this from happening again. Bc parts are really hard to come bye with this car. I'm running 48 t and 44t on stock ratio and 17t 21t with is 1 tooth larger than the stock pinion gears I don't believe that would do this but if so let me know
I really don't understand it, the bell off the engine has 2 gears fixed together meshed with 2 gears on my shaft and they all move together in tandom, there is no one gear running or the other. Either my set up is wrong or my mind blown
I've got a cheap cheap cheap smartech rc, my old one had 2spd and this newer one has only one. it seems interchangeable. I've got the complete transmission box, I've also had to change the flywheel and bell housing along with the clutch, looks like you can do it no problem.
that 1st part was utter bullshit both gears are spinning because there both being driven by the clutch bell and once rpm is high enough the arm grabs the gear and the 2nd gear grabs the centrifugal arm and then the 2nd gear drives the center drive train. There u go, The CORRECT tutorial in 50 words.
There should be about 4 screws that holds the transmission to the frame, once you take off those 4 screws the transmission should slide out of the frame of the truck.
What car do you have?
What a great video… can I ask, if that grub screw comes out by accident will the spring fall out as well?
Look up "Changing the Spur Gear on an Exceed RC Mad Beast" on our channel for how to video on how to remove the spur.
The nut that holds the spur gear on it is left hand thread, hold the spur and turn the nut clockwise and it will take the nut off.
Hi nitrorcx. I bought the forza and have been having a problem with the transmission. I used one of your videos to take it out and check it. Nothing was worn out and everything was in good condition. The only problem is it wasn't shifting onto second gear. I used this video to adjust the tension and now the car wheels lock when I'm in mid driving. Did I adjust the wrong nut? My gear mesh is set perfectly but I also tightened the brakes but like I said it was running fine so I'm guessing it isn't
Check to see if there is anything binding on the drive train on your vehicle.
Been a while since ive seen anything from you guys, great informative video.
@addictedtodat69 It's a HPI shell that we painted in the camo.
Great vid! Just got a Tornado S30 a week ago, my 3rd nitro. I was wondering if you can explain how a burned up 2nd gear and 1st is still mint? I'm thinking engine/clutch bell placement, but i've hardly hit 2nd, it had a hard time changing gears. Any advice would be greatly appreciated.
So this mean's that my car in in second gear because both spin.but they both spin at the same time even if the engine is not even running can you help and tell me whats wrong. GREAT VIDEO
Hello. may I ask for help please. I have a two speed clutch which grabs a pin on the gear, to shift to second gear. However I am not sure which way round to install the clutch. You would think common sense says the lever should fly out with the leading edge in the direction of rotation, but surely if the second gear is already spinning faster (as it is connected to a larger pinion gear) , it will simply push the lever back in, as it will brush the back edge of the lever. so my question is - Should the clutch be installed with the leading edge of the lever (the bit that comes out) facing into the direction of rotation, or away from the direction of rotation. - Thank you
There is a spring or bolt that holds the exhaust manifold to the engine, take that off and the exhaust will come off.
There isn't a reverse kit for the Nitro 1/10th scale Rally Monster
What about if it doesn't want to move at all and just revs up? All the screws are in place as far as I can tell. There's no damage to anything that I can see. I have a forza, Brand new. Ran 2 tanks and it just started revving and only catches every once in a while under very low throttle.while the weight of the car is on it. But if I pick it up, It works fine.
yeah tried that the spur gear is like stuck should i try that agian and kinda pull it off
Does temperture effect the 2 speed transmission to the point to have to re-tune it?
Hey my second gear chiped and i cant get the screws on the right side between the exhuast and the metal how do u get the exhuast out of the way or would u please make a vid of taking it all apart down to the gears please
hi i was wonderin if i buy the center differental from your store is that the 2 speed transmission and does it come w caps
Can I ask if single speed can be changed to 2 speed...is it possible?
@MrModzEverything The Mad Storm has a single speed transmission and you can't adjust it.
To replace spur gear in NITRO mad beast,do I remove or loosen center diff or do I loosen engine.Whats easier?
i had a car for over 10 years that would never shift, when it was new couldnt even rotate the spur gear to adjust it, it was locked from moving....well it turns out the adjustment screw backed itself out and jammed second gear on all the time, i had to take it all apart and put it back together now its fine, but i never seen anyone mention this so if you cant even adjust it make sure your grub screw isnt out from vibration
How can I remove the clutch hub from the shaft ?
I have a forza 1/10 buggy and I oredered a new transmission but I also need those cups. What are the part numbers on your website? Thanks
can this work on a madstorm
how can i make a four speed and reverse transmission for a 1/3 scale car and which way does the clutch open
yeah i got to where the piece where the gear box is i cant get the front and rear bones out of the box to slide it out to open it
I want my ofna to shift into second gear how much tension do I let off the clutch or how do I know the right setting?
waaitttt how can the small pinion gear be idle if it sets on the clutch bell. i mean when you put the transmission the large pinion gear sets on the small gear on the clutch bell and the small pinion gear on the transmission sets on the large of the clutch bell. so how can it be idle??
My 2 gears spin at the same time but the hasnt even kicked up:( is it my bell gear?
is there a reverse gear kit for the rally monster 1/10 scale
The manuel says its the two way drive clutch that im talking about. Im missing that middle grub screw, will that not make my forza drive? I dont even know if it had one i just bought it from nitrorcx a lil over a month ago...but all it does is rev and the gears are meshed perfectly, plz help.
can you explain to me the difference from the electric version with the engine version
From where can we buy this 2-speed Transmission separately?
Make video on how to take the madbeast nitro tansmission box out cause i chipped my second gear please
When you brake the brake cam pushess a little metal cylinder into bre pad. what is this metal cylinder i am missin it so my brakes wont work
what if both gears are spinning on idle? and when i accelerate they spin faster but the driveshaft/car does not move
exceeded rc mad beast
what do i do if my car is starting in second gear? please help
my car wont move a 2speed 4wd nitro sonic.. engine on or off the car is stuco i have loosened brake..same problem.. this happened due to changing my 1st gear plesae help
For me both of the gears on the trany spin at the same time and makes bad noises or doesn't move idk what the prob is can u help
What vehicle do you have?
what is a good temp for a tune motor
230 degrees
can you convert 1 speed engines to 2 speed....an if so how an what will i need? plz
Can any one help me I have a Ofna dm1 spac and this isn't the Frist time this happen the 2 gear stripped out. I thing the Gap was too much but not 100 sure. But how do I gap them right and prevent this from happening again. Bc parts are really hard to come bye with this car. I'm running 48 t and 44t on stock ratio and 17t 21t with is 1 tooth larger than the stock pinion gears I don't believe that would do this but if so let me know
I really don't understand it, the bell off the engine has 2 gears fixed together meshed with 2 gears on my shaft and they all move together in tandom, there is no one gear running or the other. Either my set up is wrong or my mind blown
No you cannot convert the single speed to a two speed
i don't understand my buggy. because it's already shifted into 2nd speed on idle.. can anyone explain this?
can you convert a 1 speed car to 2 speed? what all i need.. redcat volvano s30
I've got a cheap cheap cheap smartech rc, my old one had 2spd and this newer one has only one. it seems interchangeable. I've got the complete transmission box, I've also had to change the flywheel and bell housing along with the clutch, looks like you can do it no problem.
emasart
Help! My centrifugal clutch is in between these two gears.
Whats three belt transmission
bueno mi coche no tira cambio se queda en primera que opcion tengo y tengo la transmision nueva
I need one, 2 speed transmission. where can i buy one that doesn't come from china?
Uh.... What if my car is locked in place and it is extremely hard to get the wheels to move?
Liltexas 4 are your brakes on?
Is it a 2mm hex wrench for all two speed gearboxes ?
Hi guys can someone share link of 2speed box for the mad beast electric :)
Or the complete unit.
that shoe in mine won't move at all in the clutch
Spur gear is in the way
haha he said thanks for TUNING in lol
K thanks
3RD
“Basically”
Please help!
shoes not feet.
@tylerspyler2 Lol.
that 1st part was utter bullshit both gears are spinning because there both being driven by the clutch bell and once rpm is high enough the arm grabs the gear and the 2nd gear grabs the centrifugal arm and then the 2nd gear drives the center drive train. There u go, The CORRECT tutorial in 50 words.
2nd
1st
@TheCONtwo dont forget the 5th
5th
Please help