buongiorno, programmare la sicurezza dell'immobilizzatore ECU Mercedes dopo lo scambio ECU ok perfetto, la mia domanda : quadro strumentazione e leva cambio automatico su mercedes classe S,SL, ?? grazie.
Is this procedure to upload to the processor or are you writing to eproms on the ecu? I have a ecu with a dead or unresponsive processor is it possible to unsolder the eproms and transfer to a donor ecu?
Any process to Virginize this exact part number ECU, I want to use our xentry to do real initial start up properly on a used unit. Just need to clear VIN out of epprom normally, I cannot find anyone doing this ecu that way, we do lots of other with abrites or even autel.
Would it be possible to swap the chip on this board that you are reading from into another ECU? Would it work the same way as the system you are showing? Please let me know!!
I've got a 1998 c200 auto stuck in limp mode, my mechanic wiped the codes and won't tell me what they were.. i don't have a 38 to 16 pin adapter yet but have an icarsoft cr. Is there any way to manually reset the ecu and tcu etc and if i do, shouldn't the codes re appear? I've searched everywhere and my local benz garage refuse to share any knowledge without large sums of money
Do you guys specialize in ecus for the 2000 mercedes C230 kompressor located in America. I'm looking to add a small turbo compounding into the supercharger. Can you tune for something like that.
Hello, I bought a 2000 ML320 and currently in limp mode due to previous owner replaced the original PCM/ECU. -my question to you is …without the original PCM /ECU can you program a new used PCM/ECU if yes, can you do it if I send it to you? Thanks!
The Dealer told me my car, 2004 ML350, can not be fixed. The AAM went out and is now obsolete. Does you know a work a round because these computer are specific to each car and you can not substitute used parts. Great body , tires, interior, I need help!? Question, is it possible to get the ECM, AAModule, and Body controL (kEY) module from a like can with like number and re-install them in my can, WILL IT WORK. oH, YES, DO I NEED THE TRANSMISSION MODUEL ALSO. THE DEALER WILL NOT TOUCH ANY USED PARTS. THERE ARE NO MECHANICS IN THE DALLAS AREA WHO CAN HELP ME. WHERE ARE YOU , ANYWAY?
Hi I need help I got s550 2008 when I was replacing my engine mounts I broke cyl 7 ignition coil plug and I did not notice it. I started my car and parked I noticed that my engine started running ruff . I noticed that cyl 7 coil plug was broken. I instead new coils and plugs runs the same way. When I check for codes I got cylinders 7-8 codes. I removed my ecu and sent it to MODULE EXPERTS in Jacksonville Fl. For repair. After long time I got ecu back after install car didn’t start at all. I mailed it back to them after two months I got my ecu and I got the same problem as I had in beginning same codes . Misfire on7-8 cyl PLEASE HELP
Hello Dan. Well done. I have ruined a few ECU PCB's due to removing the processsor for re=programming and was quite excited when I saw this post from you. I use a XProg M Box 5.55 to program and I have tried this method of yours, but the software keep on reporting "Device is silent and timeout" Am I doing something wrong? If I remove the chip from the board then it reads and writes without any problem. Do I need to apply power to the ECU or to the Xprog M power supply socket? Thank you. Freddie
Hi Dan, Thanks for posting this. My van had lost all turbo boost and the sprinter specialist said it’s the ECU. It’s not sending a signal for turbo boost and it’s locked by Mercedes? He said I’d have to take it there and it will cost a fortune. Would I be able to buy a used computer and have it reprogrammed by you? Or would the process be the same as the video. Thanks! 2003 Dodge Sprinter 3500
Good video. It’s pretty clear with cloning. If you don’t have a programer you can swap the chips too. But do you know how to virginize the ECU - to make it fresh like you purchase it brand new from the dealer?
Just a question to be sure I understand. I have a faulty ecu on a w210 E200 and I am buying a new one, same parts number. 1. The Immo eeprom from mine needs to be transplanted into the new one and 2. the processor needs to be reprogrammed, right? Transplanting the Immo eeprom alone to the new computer will not be enough for it to work?
But changing the chip from my ecu to the other would work too? I ask because I know someone who can change chip, but I do not know someone who can program like you did
Hi sir I have a W211 Diesel 2009 E300 V6 Bluetec and I have problem with its ECU a guy who inspected told me that it's processor gone and can't be repaired! I'm searching for a used one but very hard to find its serial is CR5.4
Hi, im doing an engine swap from a 2004 S55 AMG into a 2001 SLK230. Is it possible to defeat or clone immo and use stock SLK cluster instead of having to swap s55 cluster into it?
Please my ecu is damaged, i got another one completely similar to mine from another car similar to my car , my question is it required to be reprogrammed or no? Thank you
@@vehix411 sir good morning I am always watching your videos since, 2011, but still ,I, want more knowledge ,sply electrical aers,sir,,,the, reason is ,I, am, automobile technician that's why Thanks and regards
Great job! Question. What kind of contact holders are you using? Can you give a link? Thanks. Like!
Arlabs very expansive $251
@@vehix411 wher can you get it exactly please.
I want to buy this computer full system
I mean programming tool computer
this is great. can you ECU chip tune for better performance on Mercedes bosch me2.0.1? optimize air fuel ratio and ignition timing?
great vid....Question. if a me9.7 is really bad can you remove the chip from the board and do the same
buongiorno, programmare la sicurezza dell'immobilizzatore ECU Mercedes dopo lo scambio ECU ok perfetto,
la mia domanda : quadro strumentazione e leva cambio automatico su mercedes classe S,SL, ??
grazie.
Is this procedure to upload to the processor or are you writing to eproms on the ecu? I have a ecu with a dead or unresponsive processor is it possible to unsolder the eproms and transfer to a donor ecu?
Any process to Virginize this exact part number ECU, I want to use our xentry to do real initial start up properly on a used unit. Just need to clear VIN out of epprom normally, I cannot find anyone doing this ecu that way, we do lots of other with abrites or even autel.
Would it be possible to swap the chip on this board that you are reading from into another ECU? Would it work the same way as the system you are showing? Please let me know!!
Verry clear whay bro
i like yoour whay
My looks very alike, but the motorola processor numbers are ZC432644cfn, I can't find any info on it, are those some kind of substitutes?
I've got a 1998 c200 auto stuck in limp mode, my mechanic wiped the codes and won't tell me what they were.. i don't have a 38 to 16 pin adapter yet but have an icarsoft cr. Is there any way to manually reset the ecu and tcu etc and if i do, shouldn't the codes re appear? I've searched everywhere and my local benz garage refuse to share any knowledge without large sums of money
Great clases l have 2006 E350 can u tell me where to take the ECM to get it fix? I’m in Orange County California
Go to karmanauto.come and see all your options
Very good job I really like to work with you
Do you guys specialize in ecus for the 2000 mercedes C230 kompressor located in America. I'm looking to add a small turbo compounding into the supercharger. Can you tune for something like that.
Just one question.
My Mercedes is flooded, and I'm just starting the engine and the two big fans are working. It's the problem with that?
you have to trace that problem with the car schematic.
I bet the radiator fans are switched by the FRONT SAM (under hood near brake booster)
Ur car still drives fine ? I flooded my e500 and it wont shift out of 2nd and my seats won't work
Hello,
I bought a 2000 ML320 and currently in limp mode due to previous owner replaced the original PCM/ECU.
-my question to you is …without the original PCM /ECU can you program a new used PCM/ECU if yes, can you do it if I send it to you?
Thanks!
The Dealer told me my car, 2004 ML350, can not be fixed. The AAM went out and is now obsolete. Does you know a work a round because these computer are specific to each car and you can not substitute used parts. Great body , tires, interior, I need help!? Question, is it possible to get the ECM, AAModule, and Body controL (kEY) module from a like can with like number and re-install them in my can, WILL IT WORK. oH, YES, DO I NEED THE TRANSMISSION MODUEL ALSO. THE DEALER WILL NOT TOUCH ANY USED PARTS. THERE ARE NO MECHANICS IN THE DALLAS AREA WHO CAN HELP ME. WHERE ARE YOU , ANYWAY?
Hello Sir, why do you lift that specific pin, what is the reason for that pin?
Hi can you help with stolen ecu viavro b
Hi I need help I got s550 2008 when I was replacing my engine mounts I broke cyl 7 ignition coil plug and I did not notice it. I started my car and parked I noticed that my engine started running ruff . I noticed that cyl 7 coil plug was broken. I instead new coils and plugs runs the same way. When I check for codes I got cylinders 7-8 codes. I removed my ecu and sent it to MODULE EXPERTS in Jacksonville Fl. For repair. After long time I got ecu back after install car didn’t start at all. I mailed it back to them after two months I got my ecu and I got the same problem as I had in beginning same codes . Misfire on7-8 cyl PLEASE HELP
Hello Dan. Well done. I have ruined a few ECU PCB's due to removing the processsor for re=programming and was quite excited when I saw this post from you. I use a XProg M Box 5.55 to program and I have tried this method of yours, but the software keep on reporting "Device is silent and timeout" Am I doing something wrong? If I remove the chip from the board then it reads and writes without any problem. Do I need to apply power to the ECU or to the Xprog M power supply socket? Thank you.
Freddie
Can i contact you as am just a starter but learning quickly I'm kurdish iraqi I'll appreciate your help my whatsapp 009647510525877
I am having the same issue with X prog My Ak400 got damaged it has not been easy with Xprog removing the chip and resoldering it back
Can you reprogram ME9.7 processor for my benz 2005 E280.. ecu is not responding to obd port and even no crank no start
what do you think my mb w202 c220 (110kw) ecu's price is? it is used but in good condition
Hi Dan,
Thanks for posting this. My van had lost all turbo boost and the sprinter specialist said it’s the ECU. It’s not sending a signal for turbo boost and it’s locked by Mercedes? He said I’d have to take it there and it will cost a fortune. Would I be able to buy a used computer and have it reprogrammed by you? Or would the process be the same as the video. Thanks!
2003 Dodge Sprinter 3500
Where are you located, Im in Florida and need an ECM to vin match on an engine swap project. Can you contact me?
Good video. It’s pretty clear with cloning. If you don’t have a programer you can swap the chips too.
But do you know how to virginize the ECU - to make it fresh like you purchase it brand new from the dealer?
Yes we also do virginize and we can even program key info from ignition lock if you don’t have a Mercedes computer to program the virgin ecu
@@vehix411 i have A2721533779 ECU. Any tips for virginizing it?
Please sir I have a similar problem with my Ecu the car is not firing and I have another brain but the number is not the same can it work
I have a 2006 Mercedes Benz c230 sport and my ecu went out. Can it be rebuilt and how much?
Hi bro i want swap om647 5cyl on my old c class w203 om646 4cyl. Its possible with this process? And the number of ecu ar different. Help
Just a question to be sure I understand. I have a faulty ecu on a w210 E200 and I am buying a new one, same parts number. 1. The Immo eeprom from mine needs to be transplanted into the new one and 2. the processor needs to be reprogrammed, right? Transplanting the Immo eeprom alone to the new computer will not be enough for it to work?
If the Ecu looks just like the one in this video a thick Ecu usually is on w210 then you only need to program mpu no chip
But changing the chip from my ecu to the other would work too? I ask because I know someone who can change chip, but I do not know someone who can program like you did
Hi sir I have a W211 Diesel 2009 E300 V6 Bluetec and I have problem with its ECU a guy who inspected told me that it's processor gone and can't be repaired! I'm searching for a used one but very hard to find its serial is CR5.4
Do you have damos for this ECU?
I got the same problem how can I get one ecu
how much does the tool and software cost master?
Where is the link? I need my clk430 ecu flashed.
Hi, im doing an engine swap from a 2004 S55 AMG into a 2001 SLK230. Is it possible to defeat or clone immo and use stock SLK cluster instead of having to swap s55 cluster into it?
This year merz don’t store immo in cluster
How does one stop this thing from getting wet?
so corect thank you,guy
Please my ecu is damaged, i got another one completely similar to mine from another car similar to my car , my question is it required to be reprogrammed or no? Thank you
Yes otherwise the car won’t start
Hello I like your I want you to help me to improve on my programming skills
We can talk if u like regarding a programming skill i been doing it for a year any 1 can contact me my whatsapp 009647510525877.
Thanks.
How do I get that software?
How can I get to you let chart better
Can you clone my computer on my dodge sprinter 2008 . Let me know what i need for you?
Can I send you my ecu for diagnosis?
How much do you charge for this?
Does anyone have the link to part 1
ruclips.net/video/cWMbdjNO2mI/видео.html
Hi sir 👋 it's really I like to learn from you much more ,,,,,
Well start watching my videos and maybe you will learn a thing or two
@@vehix411 sir good morning I am always watching your videos since, 2011, but still ,I, want more knowledge ,sply electrical aers,sir,,,the, reason is ,I, am, automobile technician that's why
Thanks and regards
@@vehix411 I would like to get mines reprogram
is this car-prog clone?? or original
Original china junk won’t read more then helf the stuff and will corrupt files wile reading
Neat
Hi guys does anyone have programming computer for sale?
Can I have ur contact. Will like to send u one to fix
Www.karmanauto.com 5034816575 text me what you need
@@vehix411 Sure sent it via whatsapp